Miele Kfns 3917 Sde Ed Operating And Installation Instructions

							Electrical connection U.K.
All electrical work should be carried out
by a suitably qualified and competent
person in strict accordance with current
local and national safety regulations
(BS 7651 in the UK).
The appliance is supplied with a mains
cable and moulded plug ready for
connection to an a.c. single phase
220-240 V 50 Hz supply.
Please ensure that the connection data
quoted on the data plate match the
household mains supply.
Connection should be made via a
suitable switched socket which is easily
accessible. For extra safety it is
advisable to install a residual current
device (RCD) with a trip current of 30
mA (in accordance with DIN VDE 0664,
VDE 0100, Section 739).
Do not connect the appliance to the
mains electricity supply by an extension
lead. Extension leads do not guarantee
the required safety of the appliance
(e.g. danger of overheating).
The appliance must not be connected
to an inverter and must not be used
with a plug adapter as these can cause
damage to the appliance’s electronic
unit.Non-rewireable plugs (BS 1363)
The fuse cover must be re-fitted when
changing the fuse, and if the fuse cover
is lost, the plug must not be used until a
suitable replacement is obtained. The
colour of the correct replacement cover
is that of the coloured insert in the base
of the plug, or the colour that is
embossed in words in the base of the
plug (as applicable to the design of the
plug fitted).
Replacement fuses should be ASTA
approved to BS 1362 and have the
correct rating. Replacement fuses and
fuse covers may be purchased from
your local electrical supplier.
WARNING
THIS APPLIANCE MUST BE
EARTHED
Electrical connection
31
 
						

							Do not place any appliance which
gives off heat, such as a toaster or
microwave oven, on top of this
appliance, as this would increase
the appliance’s energy consumption.
Location
The appliance should be installed in a
dry, well-ventilated room.
The room temperature should not go
above or below the climate range for
which the appliance is designed.
The higher the ambient temperature of
the room, the more energy the
appliance requires to operate.
It should not be installed where it is
exposed to direct sunlight or directly
adjacent to a heat-producing appliance
such as an oven or a radiator.
Climate range
The appliance is designed for use
within certain climate ranges (ambient
temperatures), and should not be used
outside this range. The climate range of
the appliance is stated on the data
plate inside the appliance.
Climate range Ambient room
temperature
SN
N
ST
T
SN-ST
SN-T+10°C to +32°C
+16°C to +32°C
+18°C to +38°C
+18°C to +43°C
+10 °C to +38 °C
+10 °C to +43 °C
Operating in a room which is too cold
will cause the cooling system to switch
off for too long, causing the internal
temperature in the appliance to risewith the risk of food deteriorating and
going off.
Side-by-side installation
To avoid a build-up of condensation
and resultant damage, refrigerators and
freezers should not generally be
installed side-by-side next to another
refrigerator or freezer.
However, there are certain models with
insulated side wall heating which are
suitable for side-by-side installation with
this refrigerator.
Ask your dealer which models can
be combined with your refrigerator.
^Instructions on how to install the two
appliances side-by-side are given in
the instruction booklet supplied with
the matching  freezer or
fridge-freezer.
Ventilation
Air at the back of the appliance gets
warm. To ensure sufficient ventilation,
the ventilation gaps must not be
covered over. The air inlet and outlet
must not be covered or blocked in any
way. They should be dusted on a
regular basis.
Installation
32
 
						

							Installation
^Remove any cable clips from the
back of the appliance.
^Check that all parts at the back of the
appliance are unhindered. Carefully
remove any hindrance.
^Carefully push the appliance into
position. The appliance can be
placed directly against a wall.
Aligning the appliance
^To align the appliance adjust the feet
using the spanner supplied.
Installation
33
 
						

							The appliance is supplied right hand
hinged. If left hand door hinging is
required, follow the instructions below.
Removing the door handle:
First the side section of the handle must
be removed:
^Pull door handleatowards you. Side
sectionbslides back, creating a
gapdbetween side sectionband
mounting platec.
^
Place a suitable object (e.g. a spoon
handle) in gapd, and slowly lever
the handle towards the door.
Be careful not to let the spoon
handle slip, causing damage to the
appliance.
The side sectionbcan now be
removed.
^
Pull side sectionbout of the guides
on the mounting plate.
^
Loosen the 4 screws (Torx 15) in the
mounting plate, and remove the
handle.^Remove the cover caps from the
opposite side, and fit them into the
empty holes.
Changing over the door:
^Open the appliance door.
^Use a screwdriver to lever plintha
out, then pull it forwards and out.
^
Use a screwdriver to remove cover
b, then close the door.
^
Remove screwccompletely.
^
Pull door supportdtogether with
hinge pinedownwards, then tilt it
forwards and take it off.
Changing the door hinging
34
 
						

							^Open the appliance door, tilt it
downwards and take it off.
^Remove coverf, and unscrew hinge
bracketg.
^Fit hinge pinhin the second hole of
hinge bracketg.
^
Refit bracketiand coverjturned
through 180° on the opposite side.
^
Screw hinge bracketginto the
opposite side.
TheM4 screwhas to be screwed into
the left hole of the hinge bracket.
^
Turn coverfthrough 180°, and fit it
on the other side.
^
Remove spacerkwith a screwdriver
and refit it on the opposite side.
^
Remove pluglfrom the door
bearing bush in the door and refit on
the opposite side.
^
Unscrew tappetm.
Keep it in a safe place just in case
you ever decide to change the door
hinging back to right hand hinging.
^Screw the tappet suppliedninto the
opposite side using the same screw
o.
^Hang the door on hinge pinhand
then close the appliance door.
In the following illustration the door
is not shown in the closed position to
make it easier to see what happens
next.
^
Turn door supportbaround, pull
hinge pinaout, and refit on the
opposite side.
^
Fit both parts into hinge platef. To
do this push hinge pinathrough
hinge platefinto door supportb.
Swing the door support in, push
upwards and re-assemble with screw
c.
Changing the door hinging
35
 
						

							^Align the door with the appliance
housing using the long slot in hinge
platef. Then tighten screwc.
^Refit plinth fasciad, pushing it firmly
into position.
^With the door open, position covere
in the front of the plinth fascia, and
push it firmly into position.
Refitting the handle:
Please make sure you follow the
instructions below carefully when
you refit the handle. The door seal
will be damaged if the handle is
fitted incorrectly.
^
Loosely attach the handle to the
opposite side of the door with the two
front screwsb.
Mounting platecmust be positioned
on the side of the door so that when the
door isclosedit is flush with the side of
the appliance.
If this is not the case,
^
Tighten both grub screwsawith the
allen key provided until mounting
plateclines up correctly.^Then tighten all 4 fixing screwsb.
^Slide the side section of the handle
dinto the guides on the mounting
plate until it clicks into place.
It is important to check that the side
section of the handleddoes not
come into contact with the door seal
when opening the door, as this
would damage the door seal
permanently.
If, after you have refitted the handle,
you find that the side section does
touch the door seal when the door is
opened:
^Realign mounting platecwith grub
screwsauntil the mounting plate
and the side section of the handled
are at the correct angle and the side
section does not touch the seal when
the door is opened.
Changing the door hinging
36
 
						

							StayFresh zone compartments
^Pull the compartment right out by
taking hold of it at the back and lifting
it up to remove it.
^Pull the compartment lid forwardsa.
^Push the compartment lid in towards
the side that the appliance is going to
be opened from once the hinges
have been changed overb, and fit it
back on the runners.
^Push the lid in until it engagesc.
^
To put the compartment back in, pull
the runnersaright out and place the
compartment on top of the runners
close up against the door opening
side.The front of the runners must
be right up against the front of the
compartmentb.The compartment
will click into position. You can now
push the compartment back inc.
Make sure that the compartment lid
covers the compartment correctly.
Changing the door hinging
37
 
						

							600 mm wide appliancescan be
installed into a kitchen run. To match
the height of the rest of the kitchen, the
appliance can be fitted with a suitable
top boxa.
A ventilation gap of at least 50 mm
depth must be allowed for behind the
appliance and top box, if fitted, for air
to circulate.
A gap of at least 40 mm is required
between the top of the appliance (or
top box) and the ceiling to ensure that
air can circulate without hindrance.
Otherwise the appliance has to work
harder, resulting in an increase in
electricity consumption.
The air inlet and outlet must not be
covered or blocked in any way.
They should be dusted on a regular
basis.
When built into a kitchen run (max.
depth 580 mm) the appliance can be
installed directly next to a kitchen
furniture housing unit. The appliance
doorbwill protrude in front of furniture
fronts at the sides by 34 mm and by
51 mm in the middle of the door. This
enables the doors to be opened and
shut without being obstructed.
Wheninstalled next to a wallca
distance of approx. 36 mm is needed
on the hinge side between the wall and
the appliance, so that the door and the
handle have sufficient space for
opening.
Building in the appliance
38
 
						

							39
 
						

							Alteration rights reserved / 5005
K 8967 S ed-1M.-Nr. 06 777 930 / 00
en-GB