Miele Kfn12924sd-1 Manual

In the event of a fault which you cannot
correct yourself, or if the appliance is
under guarantee, please contact:
–your Miele Dealer
or
–Miele
(see back cover for contact details).
When contacting your Dealer or Miele,
please quote the model and serial
number of your appliance. This
information is given on the data plate
inside your appliance.
Please note that telephone calls may
be monitored and recorded for
training purposes.
N.B. A call-out charge will be applied
for service visits where the problem...

Electrical connection U.K.
All electrical work should be carried out
by a suitably qualified and competent
person in strict accordance with current
local and national safety regulations
(BS 7671 in the UK).
The appliance is supplied with a mains
cable and moulded plug ready for
connection to an a.c. single phase
220-240 V 50 Hz supply.
Please ensure that the connection data
quoted on the data plate match the
household mains supply.
Connection should be made via a
suitable switched socket which is easily...

Do not place any appliance which
gives off heat, such as a toaster,
mini-oven or double burner hob, on
top of this appliance There is the
danger of these catching fire.
This appliance must not be installed
directly next to another refrigerator
or freezer.
It does not have side-wall heating,
so installation next to another
refrigerator or freezer could cause a
build-up of condensation between
them.
Further information is available from
your dealer.
Location
This appliance should be installed in a
dry,...

Ventilation
Air at the back of the appliance gets
warm. To ensure sufficient ventilation,
the ventilation gaps must not be
covered or blocked in any way. They
should be dusted on a regular basis.
Appliances with wall spacers
supplied
The wall spacers supplied with
some appliances must be used in
order to achieve declared energy
consumption values. Appliance
depth is increased by approx. 35
mm with the wall spacers fitted. If
the wall spacers are not used, this
does not influence the functionality
of the...

Levelling the appliance door
Ensurethat you unscrew adjusting
footfrom the hinge plate until it sits
on the floor. Then unscrew the foot by
a further 90°.
Installation
45 

Appliance dimensions
ABC
KFN 12823 SD-1/-2
KFN 12823 SD edt/cs-11817 600 mm 630 mm*
KFN 12923 SD-1/-2
KFN 12923 SD edt/cs-1/-2
KFN 12924 SD-1
KFN 12924 SD edt/cs -12010 600 mm 630 mm*
* Dimensions without wall spacers fitted. Appliance depth is increased by approx.
35 mm with the supplied wall spacers fitted.
Installation
46 

The appliance is supplied right-hand
hinged. If left-hand door hinging is
required, follow the instructions below.
To change the door hinging you will
need the following tools:
Two people are needed for
changing the door hinging.Removing the door handles
Pull door handletowards you. Side
sectionslides back.
Pull side sectionfirmly back out of
the guides on the mounting plate.
Undo the 4 screws (TX 15) in the
mounting plate, and remove the
handle.
Remove the cover caps from the
opposite side, and...

Removing the doors
Make sure the door shelves are
empty.
Close the upper door.
Remove coverby sliding it
forwards from the back and then
lifting it off.
Remove coverby pulling it
upwards.
Caution. The upper door is not
secure as soon as the upper hinge
plate is removed.

Loosen screwsin upper hinge
plateand pull it upwards and off.

Carefully lift the upper door off and
place it to one side.

Carefully ease off coverfrom
above using a screwdriver and then
take it off together with retaining...

Close the lower appliance door.
Caution. The lower door is not
secure as soon as the middle hinge
plate is removed.
Pull the middle hinge pin
upwards
to remove it.
Carefully lift the lower door off and
place it to one side.
Pull coveroff.
Unscrew hinge plate, turn it
through 180° and fit it on the opposite
side.

Pull off plastic cap	, turn it through
180° and fit it back on to hinge plate
.

Refit coveron the opposite side.Remove cap
from the bearing
bush in the door and refit on the...

Changing over the doors
Pull hinge pintogether with disc
and adjustable footupwards and
off.
Remove cover cap.
Undo screwsand take hinge plate
off.
Undo the screw of hinge part	on
hinge plateslightly. Fit it into the
hole opposite in hinge plateand
tighten up the screw.

Refit cover capin the other hole.

Remove coverand fit it into the
holes on the opposite side.Screw hinge plateinto position on
the opposite side using the twoouter
long slots only. To make it possible to
align the door...