Miele Kfn 9753 Id Operating And Installation Instructions

							Removing the door closing device
^With its exterior facing downwards,
place the appliance door on a stable
surface.
^Leave the hinges open and remove
the screw in the mountinga.
Caution! When uninstalled, the door
closing device will snap shut.
^Loosen the ball jointbusing an
open ended wrench.
^
Remove the door closing devicec
together with theball joint.
Do not remove the door closing
device from the ball joint!
This will damage the device.^Stand the appliance doors up
individually, and loosen the hinges on
the front (hinges remain open).
^Pull out the plugsafrom the top,
middle and bottom (if the plugs are
not in the doors, the are included
separately in the packaging).
^
Remove the screws from all the
hingesb.
^
Relocate each hinge diagonally in the
opposite corner.
Donotclose the hinges.
Risk of injury!
^
To tighten the hinges, use a power
screwdriver – the screwsbare
self-tapping.
^
Use the plugsato close the holes
on the opposite side.
Adjusting the door hinges
41
 
						

							Fastening the dampers
^With its exterior facing downwards,
again place the appliance door on a
stable surface.
^Screw the ball jointbof the door
closing devicecinto the new fixing
hole.
^Pull the door closing devicecapart
and hook the mountingaonto the
hinge.
^Hold the door closing device in this
position and screw the mountinga
to the hinge.^Hang the appliance doors on the
pre-fitted screws and push the doors
inward.
^Tighten the screws at the top, middle
and bottom.
^Snap on the coversa,bandc.
^Replace the plugsd.
^
Insert the pins from above (if
necessary).
Adjusting the door hinges
42
 
						

							The following installation instructions
are for aright-hingedappliance
door. If you have converted the
appliance door to be left-hinged,
you will need to adapt the
instructions accordingly.
Tools needed:
–a Philips head screwdriver,
–various sizes of Torx screwdrivers,
–an open-ended wrench.
Custom door panels
The total weight of the panel(s) must
not exceed the following, otherwise the
hinges may be damaged:
KFN 9753 iD
Upper door..................... 31 lbs (14 kg)
Lower door..................... 27 lbs (12 kg)
Installing the appliance as a
room divider
If you wish to install the appliance as a
room divider, the back of the installation
niche must be fitted with a panel, so the
back of the appliance is not exposed.
Aligning the installation niche
Before installing the appliance, the
cabinetry must be carefully aligned
using a level. The cabinetry corners
must be at 90° angles, otherwise the
custom door panels will not be flush
with all 4 corners of the cabinetry.
Installing the appliance
43
 
						

							Preparing the appliance
^Slide the cover stripa(nobs facing
downwards) into the holder. The
nobs will fit into the holesb.
^Ensure that the power cord can be
easily plugged in once the appliance
is installed.
^
Screw the provided fixing bracketsc
into the pre-drilled holes in the
appliance door using a hex screwd.
(If the custom door panel is large,
screw on an additional pair of brackets
cnear the door handle.)^Push the appliance two-thirds of the
way into the installation niche.
Ensure that the power cord does not
get caught.
^For 16 mm cabinetry walls only:
Clip the spacerseandfonto the
upper and lower hinges.
Installing the appliance
44
 
						

							^Open the appliance doors.
^Using the screwsh(M5 x 22), screw
the plastic bracketgto the door
opening.
^
Using the screwsj, loosely secure
the fixing bracketionto the
appliance.
^
If necessary, shorten the sealing strip
kto match the height of the niche.
Remove the protective film.
^
Starting at the bottom edge of the
fixing bracketi, stick the sealing
stripkon so that it is even with the
front of the appliance on the side the
door opens.Installing the appliance
Depending on the thickness of the
niche walls, push the appliance in until :
–
the spacers touch the wallsa[5/8
(16 mm) wall thickness].
or
–
the front edges of the hinges are
flush with the niche wallb[3/4
(19 mm) wall thickness].
^
Use an open-ended wrench adjust
the height-adjustable feet as needed,
until the appliance is levelc.
^
Ensure that the plastic bracketdis
flush with the front edge of the niche
walls.
This ensures that a space of 1 5/8
(42 mm) to the front edges of the side
walls is kept.
Installing the appliance
45
 
						

							This space must also be taken into
account with cabinetry that has a
receding base, even if it means that the
plastic bracketdwill project beyond
the base of the cabinetry.
^If the cabinetry has door stops (i.e. to
protect from slamming): pull the
appliance forward by distancehso
that a space of 1 5/8 (42 mm) is
created.
The hinges now project by distanceh
and the plastic bracketdlines up with
the front edge of the hinge.
If the required distance of 1 5/8
(42 mm), from the body of the
appliance to the front side of the
cabinetry side wall, is not observed,
the appliance door may not close
properly, causing malfunctions.
Attaching the appliance to the
installation niche
^Push the hinged side of the
appliance to the niche wall.
^
Screw the long screwsa
(4 x 19 mm) into all of the hinge
plates.
^
Open the plastic bracket and screw a
long screwb(4 x 19 mm) through
the middle of the long hole.
^
Close the plastic bracket.
Installing the appliance
46
 
						

							^Screw the screwcthrough the fixing
bracketd.
^Push the bracket towards the niche
wall and tighten the screwse.
^
Close the bracketf.
^
Close the appliance doors.
Mounting the custom door
panels
^Set a gap of 5/16 (8 mm) between
the appliance door and the fixing
bracketa.
^Slide the mounting aidsbto the
height of the custom door: The lower
edgeXof the mounting aids must be
at the same height as the upper edge
of the custom door to be mounted
(see-in the illustration).
^
Unscrew the nutsc, remove the
fixing bracketdand the mounting
aids.
Installing the appliance
47
 
						

							^With a pencil, lightly mark a line down
the center of the inside of the custom
door.
^Hang the fixing bracketdwith the
mounting aids on theinsideof the
custom door. Align the bracket
centrally.
^
Secure the fixing bracket with at least
6 screwse(4 x 14 mm). (For
framed doors, use only 4 screws at
the edge).
^
Carefully pull the mounting aids up
and outf.
^
Turn them around, and fit them into
the middle slots of the fixing bracket
gfor safe keeping.^Hang the custom door on the
adjusting boltsh.
^Loosely attached the nutsconto the
adjusting bolts.
^Close the door. Check the distance
between the custom door and
adjacent cabinetry doors.
^Align the custom door with the
adjacent cabinetry doors:
Side adjustmentsXare achieved by
sliding the cabinetry door.
Height adjustmentsYare achieved
by turning the adjustment boltsh
with a flathead screwdriver.
^
Tighten the nutsc.
Installing the appliance
48
 
						

							Securing the appliance door to the
custom door panel
^Secure the fixing bracket using the
pre-drilled holesausing the (4 x
14 mm) screwsb.
Ensure that the two metal edges are
flush (symbol//).
– Align depthZon the custom door:
Loosen the screws at the top of the
appliance doorscand the bottom of
the fixing bracketd. Adjust the
custom door to create a space of
1/16 (2 mm) between the custom
door and the front edge of the niche.^Close both the doors and align them
with the adjacent cabinetry doors.
^While holding the adjusting boltsg
with a screwdriver, tighten the nutse
on the appliance doors using a
wrenchf.
^
The cover striphmust not protrude,
it must be completely inside in the
niche.
^
Re-tighten all the screws.
^
Secure the appliance again at the
bottom with a screwithrough the
round hole in the plastic bracketj.
^
Close the plastic bracket.
Installing the appliance
49
 
						

							^Replace the upper coverk.
^Replace the side coversl.
^Replace the side coversm.
Be sure all of the covers click into
place.The following confirms that the
appliance is installed correctly:
–The doors close properly.
–The doors do not touch the
cabinetry.
–The seal at the upper corner of the
hinged-side contacts tightly.
^To verify this, place a flashlight in the
appliance and close the appliance
doors.
Turn off the lights and check whether
the light is visible from inside the
appliance. If light is seen, check the
individual installation steps again.
Installing the appliance
50