Miele Kfn 8995 Seed Operating And Installation Instructions

							^Remove the two screws from the top
of the bearing block.
^Swing the door out to the side, then
lift it up and off.
Refitting the parts:
^
Unscrew bearing blocke.
^
Remove coverf.
^
Refit coverfon the opposite side by
turning it 180° and then pushing it in
from the side. Netx, turn the earthing
contactgaround and fit it on the
opposite side, too.^Fit the spacer bushings at the back
of the bearing block on the opposite
side.
^Screw the bearing block onto the
opposite side.
^
Pull the grey cover on the bearing
block forwards (1) and push it into
the other side of the bearing block
(2).
Changing the door hinging
51
 
						

							Exchange coverhin the middle of the
appliance with hinge bracketi.Todo
this:
^Unscrew coverhand hinge bracket
i.
^Pull bearing bushingkupwards out
of the hinge bracket and then pull
hinge pinjdownwards and off.
^Turn the cover and bracket around
and screw them securely into the
opposite side.
^Replace bearing bushingkinto
hinge bracketifrom above and
then push hinge pinj, long side
first, from below into the hinge
bracket.
Important:When fitting the bearing
bushing and the hinge pin, make
sure that they both fit correctly in the
hinge bracket.Refitting parts in the upper appliance
door:
^Pull the bearing bushing approx. 2
cm out of the door (1).
^Using a screwdriver, carefully
remove the covers from both sides
(2).
^
Loosen both screws in the insert (see
arrows).
Changing the door hinging
52
 
						

							^Using flat-nosed pliers, carefully pull
the insert out together with the entire
cable loop.
Donotpull on the cable to remove
the insert - you could damage it!
^
Remove the stoppers and replace
them on the opposite side.
^
Replace the cable loop and insert on
the opposite side.
^
Screw the insert securely into
position.
^
Fit the covers back onto both sides.
CoverA(marked on the underside of
the cover)goes on the side with the
cable, CoverB on the other side!
^
Push the bearing bushing securely
into position until there is almost nogap between it and the top of the
door.
Refitting the appliance doors:
^Fit the stoppers into the top of the
freezer section door.
^Hang the lower door on hinge pinj
and then close the appliance door.
^Fit lower hinge bracketbin the door
bearing bushing of the lower door.
Then screw it securely to the
housing.
^
Refit covera.
^
Fit the top appliance door onto
middle hinge pinj.
^
Open the door.
Changing the door hinging
53
 
						

							^Secure the appliance door to the
bearing block using both top screws.
Push the bearing bushing up to the
bearing block until the screws
connect with the thread.
^Open the door to the refrigerator
section.
^
Place the cable behind the bearing
block.^The cable should lie close to the
guides in the bearing block.
^
Connect the cable plug in the
appliance and fold the holder back to
the side.
Changing the door hinging
54
 
						

							^Push the cover back over the plugs
and the bearing block.
^Clip the bearing block cover back
into position at the top of the
appliance.
Refitting the handles:
Please make sure to carefully follow
the instructions below when you refit
the handle. The door seal will be
damaged if the handle is fitted
incorrectly.
^
Loosely attach the handle to the
opposite side of the door with the two
front screwsb.Mounting platecmust be positioned
on the side of the door so that when the
door isclosedit is flush with the side of
the appliance.
If this is not the case
^tighten the two grub screwsawith
the Allen key provided, until mounting
plateclines up correctly.
^Then tighten all 4 fixing screwsb.
^Slide the side section of the handle
dinto the guides on the mounting
plate until it clicks into place.
It is important to check that the side
section of the handleddoes not
come into contact with the door seal
when opening the door, as this
would damage the door seal
permanently.
If, after you have refitted the handle,
you find that the side section does
touch the door seal when the door is
opened:
^
Realign mounting platecwith grub
screwsauntil the mounting plate
and the side section of the handled
are at the correct angle and the side
section does not touch the seal when
the door is opened.
Changing the door hinging
55
 
						

							The appliance can be installed in any
kitchenette. To match the appliance to
the height of the kitchenette, a suitable
adapter cabinetacan be installed
over the appliance.
A ventilation gap of at least 50 mm (2)
depth must be left behind the
applicance. The gap between the
appliance/adapter cabinet and the
room ceiling must be at least 40 mm
(1 9/16), so that warm air can escape
without obstruction. Otherwise the
appliance has to work harder, which
results in increased energy
consumption. The greater the
ventilation cross-section, the more
energy-efficient the appliance can be.
The air intake and outlet must not be
blocked or covered in any way. They
also need to be dusted/cleaned on a
regular basis.
If the appliance is installed next to a
wallc, a gap of approx. 50 mm (2) is
needed on the hinge side between the
wall and the applianceb, so that the
appliance doors can be completely
open, with space for the handle.
Installing the appliance
56
 
						

							57
 
						

							58
 
						

							59
 
						

							Subject to change without notice / 3407
KFN 8995 SD ed-1
KFN 8996 SDE ed-1M.-Nr. 06 921 010 / 00