Miele Kfn 8762 Sed Operating And Installation Instructions

							Installation
^Remove any cable clips from the
back of the appliance.
^Check that all parts at the back of the
appliance are unhindered. Carefully
remove any hindrance.
^Carefully push the appliance into
position. The appliance can be
placed directly against a wall.
Aligning the appliance
^To align the appliance adjust the feet
using the spanner supplied.
Installation
41
 
						

							The appliance is supplied right hand
hinged. If left hand door hinging is
required, follow the instructions below.
Removing the door handles:
First the side section of the handle must
be removed:
^Pull door handleatowards you. Side
sectionbslides back, creating a
gapdbetween side sectionband
mounting platec.
^
Place a suitable object (e.g. a spoon
handle) in gapd, and slowly lever
the handle towards the door.
Be careful not to let the spoon
handle slip, causing damage to the
appliance.
The side sectionbcan now be
removed.
^
Pull side sectionbout of the guides
on the mounting plate.
^
Loosen the 4 screws (Torx 15) in the
mounting plate, and remove the
handle.^Remove the cover caps from the
opposite side, and fit them into the
empty holes.
Changing over the doors:
^Open the lower door.
^Use a screwdriver to lever plintha
out, then pull it forwards and out.
^
Use a screwdriver to remove cover
b, then close the door.
^
Remove screwccompletely.
^
Pull door supportdtogether with
hinge pinedownwards, then tilt it
forwards and take it off.
^
Open the lower appliance door, move
it downwards and take it off.
^
With the upper doorgclosed, pull
hinge pinfdownwards to remove it.
^
Open the upper door, and pull it
downwards and off.
Changing the door hinging
42
 
						

							^Remove coverh, and unscrew hinge
bracketi.
^Fit hinge pinjin the second hole of
hinge bracketi.
^Refit bracketkand coverlturned
through 180° on the opposite side.
^
Screw hinge bracketiinto the
opposite side.
TheM4 screwhas to be screwed into
the left hole of the hinge bracket.
^
Turn coverhthrough 180°, and fit it
on the other side.
^
Exchange covermin the middle of
the appliance with hinge bracketn.
To do this:
Unscrew covermand hinge bracket
n, turn them around and screw in on
the opposite side.
^
Pull bearing bushodownwards out
of hinge bracketnand refit it from
above into the hinge bracket.^Remove spacerpwith a screwdriver
and refit it on the opposite side.
^Remove plugsqfrom the door
bearing bushes in the doors and refit
on the opposite side.
^Hang the door on hinge pinjand
then close the appliance door.
^Push middle hinge pinffrom below
through hinge bracketninto the
upper appliance door.
^Check that the upper door is
correctly aligned. If necessary, align
it using the long slots in hinge
bracketn.
^Hang the lower door in hinge bracket
nthen close the appliance door.
Changing the door hinging
43
 
						

							In the following illustration the lower
door is not shown in the closed
position to make it easier to see
what happens next.
^Turn door supportdaround, pull
hinge pineout, and refit on the
opposite side.
^
Fit both parts into hinge platef. To
do this push hinge pinethrough
hinge platefinto door supportd.
Swing the door support in, push
upwards and re-assemble with screw
c.
^
Align the lower door with the
appliance housing using the long slot
in hinge platef. Then tighten screw
c.
^
Refit plinth fasciaa, pushing it firmly
into position.^With the lower door open, secure
coverbto the front of the plinth
fascia.
Refitting the handles:
Please make sure you follow the
instructions below carefully when
you refit the handle. The door seal
will be damaged if the handle is
fitted incorrectly.
^Loosely attach the handle to the
opposite side of the door with the two
front screwsb.
Mounting platecmust be positioned
on the side of the door so that when the
door isclosedit is flush with the side of
the appliance.
If this is not the case,
^
Tighten both grub screwsawith the
allen key provided until mounting
plateclines up correctly.
^
Then tighten all 4 fixing screwsb.
^
Slide the side section of the handle
dinto the guides on the mounting
plate until it clicks into place.
Changing the door hinging
44
 
						

							It is important to check that the side
section of the handleddoes not
come into contact with the door seal
when opening the door, as this
would damage the door seal
permanently.
If, after you have refitted the handle,
you find that the side section does
touch the door seal when the door is
opened:
^Realign mounting platecwith grub
screwsauntil the mounting plate
and the side section of the handled
are at the correct angle and the side
section does not touch the seal when
the door is opened.
Changing the door hinging
45
 
						

							The appliance can be installed in a
kitchen run. To match the height of the
rest of the kitchen, the appliance can
be fitted with a suitable top boxa.
A ventilation gap of at least 50 mm
depth must be allowed for behind the
appliance and top box, if fitted, for air
to circulate.
A gap of at least 40 mm is required
between the top of the appliance (or
top box) and the ceiling to ensure that
air can circulate without hindrance.
Otherwise the appliance has to work
harder, resulting in an increase in
electricity consumption.
The air inlet and outlet must not be
covered or blocked in any way.
They should be dusted on a regular
basis.
When built into a kitchen run (max.
depth 580 mm) the appliance can be
installed directly next to a kitchen
furniture housing unit. The appliance
doorbwill protrude in front of furniture
fronts at the sides by 34 mm and by
51 mm in the middle of the door. This
enables the doors to be opened and
shut without being obstructed.
Wheninstalled next to a wallca
distance of approx. 36 mm is needed
on the hinge side between the wall and
the appliance, so that the doors and
handles have sufficient space for
opening.
Building in the appliance
46
 
						

							47
 
						

							Alteration rights reserved / 1606
KFN 8562 SD ed, KFN 8762 SD ed, KFN 8763 SD ed, KFN 8962 SD edM.-Nr. 06 208 653 / 00
en/GB