Miele Kfn 14842 Sded Operating And Installation Instructions

							Replacing the upper soft-close door
mechanism
^Remove coverafrom panelb,
rotate it by 180° and refit it on the
other side.
^
Clip the spacer into position on the
handle side (A).
^
Then clip the soft-close mechanism
into position on the hinge side (B).
Then push both parts from the
middle until they click firmly into
position.^Screw the spacer and the soft-close
mechanism together securely using
screwc.
^Attach panelbto soft-close
mechanism bracketd.
^
Push covereon from the side so
that the openings for the pinfare
vertically aligned.
^
Align bracketdto the hinge plate,
and insert pinffrom above so that
the right angle fits into the recess.
^
Clip covereinto position.
Make sure that coverefits properly so
that the door can be closed without
hindrance and the pin is protected.
Changing the door hinging
61
 
						

							^Remove retaining clipg.
^Replace panelbonto the soft-close
mechanism from above, clicking it
back into place first at the bottom
and then at the top.
^Close the upper door.
Refitting the handles
Please make sure you follow the
instructions below carefully when
you refit the handles. The door seal
will be damaged if the handle is
fitted incorrectly.
^
Loosely attach the handle to the
opposite side of the door with the two
front screwsb.Mounting platecmust be positioned
on the side of the door so that when the
door isclosedit is flush with the side of
the appliance.
If this is not the case,
^tighten both grub screwsawith a
suitable allen key until mounting plate
clines up correctly.
^Then tighten all 4 screwsb.
^Slide the side section of the handle
dinto the guides on the mounting
plate until it clicks into place.
It is important to check that the side
section of the handleddoes not
come into contact with the door seal
when opening the door, as this
would damage the door seal
permanently.
If, after you have refitted the handle,
you find that the side section does
touch the door seal when the door is
opened:
^
Realign mounting platecwith grub
screwsauntil the mounting plate
and the side section of the handled
are at the correct angle and the side
section does not touch the door seal
when the door is opened.
Changing the door hinging
62
 
						

							The appliance doors can be aligned
with the housing after they have been
fitted.
In the following illustration the door
is not shown in the closed position to
make it easier to see what you have
to do.
To align thelower dooruse the long
outer slots in the lower hinge plate:
^Remove centre screwafrom the
hinge plate.
^
Slightly loosen both outer screwsb.
^
Align the door by sliding the hinge
plate to the left or right.
^
Then tighten screwsbagain. Screw
adoes not need to be used again.To align theupper dooruse the long
outer slots in the middle hinge plate:
^Slightly loosen the three screwsc.
^Align the door by sliding the hinge
plate to the left or right.
^Then tighten screwsc.
Aligning the appliance doors
63
 
						

							aTop box
bAppliance
cHousing unit
dWall
The appliance can be installed in a
kitchen run. To match the height of the
rest of the kitchen, the appliance can
be fitted with a suitable top boxa.
A ventilation gap of at least 50 mm
depth must be allowed for behind the
appliance across the entire width of the
top box for air to circulate.
The cross section of the air outlet under
the room ceiling must be at least
300 cm
2to ensure that air can circulate
without hindrance. Otherwise the
appliance has to work harder, resulting
in an increase in electricity
consumption.
The air inlet and outlet must not be
covered or blocked in any way.
They should be dusted on a regular
basis.
When built into a kitchen run (max.
depth 580 mm) the appliance can be
installed directly next to a kitchen
furniture housing unit. The appliance
door will protrude in front of furniture
fronts at the sides by 34 mm and by
55 mm in the middle of the door. This
enables the doors to be opened and
shut without being obstructed.
When installednext to a wallda
distance of approx. 55 mm must be
maintained on the hinge side between
the walldand the applianceb,so
that the doors and the handles have
sufficient space for opening.
Building in the appliance
64
 
						

							65
 
						

							66
 
						

							67
 
						

							Alteration rights reserved / 0811
KFN 14943 SD, KFN 14943 SD ed/cs, KFN 14842 SD ed/csM.-Nr. 09 020 880 / 01