Miele Kfn 14842 Sded Operating And Installation Instructions

Ventilation
Air at the back of the appliance gets
warm. To ensure sufficient ventilation,
the air inlet and outlet must not be
covered or blocked in any way. They
should be dusted on a regular basis.
Installation
^Remove the cable clip from the back
of the appliance.
^Check that all parts at the back of the
appliance are unhindered. Carefully
remove any hindrance.
^Carefully push the appliance into
position with the back against the
wall.
Aligning the appliance
^To align the appliance, adjust the
front...

Appliance dimensions
ABC
KFN 14842 SD ed/cs1860 750 630
KFN 14943 SD ed/cs
KFN 14943 SD2020 750 630
Installation
52
 

The appliance is supplied right-hand
hinged. If left-hand door hinging is
required, follow the instructions below.
To change the door hinging you will
need the following tools:
–a cross-slotted screwdriver,
–a flat-bladed screwdriver,
–a selection of Torx screwdrivers,
–a spanner.
Two people are needed for
changing the door hinging.
Removing the door handles
^
Pull door handleatowards you. Side
sectionbslides back.
^
Pull side sectionbfirmly back out of
the guides on the mounting plate.
^
Undo the 4...

Before beginning, make sure that
the door shelves are empty.
Removing the soft-close mechanism
for the upper door
^Open the upper door.
^Remove panelafrom the soft-close
mechanism by inserting a flat-bladed
screwdriver into the gap from above
and easing it off bit by bit.
Take care not to damage the door
seal.
If the door seal is damaged, the
door will not close properly and
cooling will be impaired.^Slide panelatowards the appliance,
and leave it hanging between the
door and the appliance.
^Fit...

^Remove coverd.
The soft-close mechanism is now no
longer fixed to the appliance.
^Remove panela.
^Slide soft-close mechanism bracket
fas far as it will go towards the
handle side of the door.
^Undo screwgon the soft-close
mechanism and the spacer.
^Using a flat-bladed screwdriver push
the centre of the soft-close
mechanism towards the middle of the
door.
^
Then prise the soft-close mechanism
out of the hinge side of the door.
^
Then place it to one side.
^
Push the spacer out towards the
hinge side.
^...

Caution. The upper door is not
secure as soon as the upper hinge
plate is removed.
^Close the upper door.
^Undo screwsmin upper hinge plate
nand pull it upwards and off.
^Carefully lift the upper door off and
place it to one side.
^Make sure that you leave the hinge
pin in the hinge plate in the middle of
the appliance, as otherwise the lower
door will be unsecured.
^Then fit coverhtogether with
retainer plateion the opposite side.
^Refit coverlon the opposite side.
Removing the lower soft-close door...

^Push hinge pineup and out from
underneath.
The soft-close mechanism is now no
longer fixed to the appliance.
^Remove panela.
^
Slide soft-close mechanism bracket
fas far as it will go towards the
handle side of the door.
^
Undo screwgon the soft-close
mechanism and the spacer.
^
Using a flat-bladed screwdriver push
the centre of the soft-close
mechanism towards the middle of the
door.
^
Then prise the soft-close mechanism
out of the hinge side of the door.
^
Then place it to one side.
^
Push the spacer...

^Remove caplfrom the bearing
bush in the door and refit on the
opposite side.
Refitting the lower door
^
Pull hinge pinatogether with discb
and adjustable footcupwards and
off.
^
Remove cover capd.
^
Undo screwseand take hinge plate
foff.^Unscrew partgfrom hinge platef,
rotate it by 180° and refit into the hole
on the opposite side of the hinge
plate.
^Refit cover capdin the other hole.
^Remove coverh.
^Unscrew and refit screwiinto the
outer hole on the opposite side.
^Turn coverhthrough 180°, and fit...

^Fit hinge piniinto middle hinge
platekin the lower door.
Replacing the lower soft-close door
mechanism
^
Remove coverafrom panelb,
rotate it by 180° and refit it on the
other side.^Clip the spacer into position on the
handle side (A).
^Then clip the soft-close mechanism
into position on the hinge side (B).
Then push both parts from the
middle until they click firmly into
position.
^
Screw the spacer and the soft-close
mechanism together securely using
screwc.
Changing the door hinging
59
 

^Attach panelbto soft-close
mechanism bracketd.
^Align bracketdto the hinge plate,
and insert pinefrom above so that
the right angle fits into the recess.
^Click coverfback into place.
Make sure that coverffits properly so
that the door can be closed without
hindrance and the pin is protected.
^Remove retaining clipg.
^
Replace panelbonto the soft-close
mechanism from above, clicking it
back into place first at the bottom
and then at the top.
^
Close the lower door.Refitting the upper door
^Then fit the...