Miele Kfn 12923 Sded Operating And Installation Instructions

							The appliance is supplied right-hand
hinged. If left-hand door hinging is
required, follow the instructions below.
To change the door hinging you will
need the following tools:
–a cross-slotted screwdriver,
–a flat-bladed screwdriver,
–a selection of Torx screwdrivers,
–a spanner.
Two people are needed for
changing the door hinging.
Removing the door handles:
^
Pull door handleatowards you. Side
sectionbslides back.
^
Pull side sectionbout of the guides
on the mounting plate.
^
Undo the 4 screws (Torx 15) in the
mounting plate, and remove the
handle.
^
Remove the cover caps from the
opposite side, and fit them into the
empty holes.
Changing the door hinging
41
 
						

							To remove the doors:
Make sure the door shelves are
empty.
^Close the upper door.
^Remove coveraby sliding it
forwards from the back and then
lifting it off.
^Remove coverbby pulling it
upwards.
Caution. The upper door is not
secure as soon as the upper hinge
plate is removed.
^
Loosen screwsdin upper hinge
platecand pull it upwards and off.
^
Carefully lift the upper door off and
place it to one side.
^
Carefully loosen coverefrom above
using a screwdriver and then take it
off together with retaining platef.
^
Then separate retaining plateffrom
covere, by pushing it slightly to the
left. Then pull the cover forwards and
off.
^
Rotate retaining platefby 180°.^Then fit coverefrom the front over
retaining platef, and slide it over to
the right. The writing must be visible.
^Remove coverg, then rotate it by
180° and fit it on the opposite side.
^Then fit coveretogether with
retaining platefon the opposite
side.
Changing the door hinging
42
 
						

							^Close the lower appliance door.
^Pull plastic coverhoff.
^Pull the middle hinge piniupwards
to remove it.
^Carefully lift the lower door off and
place it to one side.
^Pull coverjoff.
^Unscrew hinge platek, turn it
through 180° and fit it on the opposite
side.
^Turn plastic coverh180° and refit it
in the centre of hinge platek.
^
Refit coverjon the opposite side.^Remove caplfrom the bearing
bush in the door and refit on the
opposite side.
^Remove spring clampmfrom
underneath the door and fit it on the
opposite side.
Changing the door hinging
43
 
						

							Changing over the doors:
^Remove coveraby pulling it
forwards.
^With the help of another person,
carefully tilt the appliance backwards
and pull hinge pinbout.
^Do not lose hinge bushc.
^Undo screwsdand take hinge plate
eoff.
^Remove coverfand fit it into the
holes on the opposite side.
^
Unscrew bearinggfrom hinge plate
eand screw it into the hole on the
other side of hinge platee.^Screw hinge plateeinto position on
the opposite side using the twoouter
long slots only. Do not use the middle
hole because you will not be able to
align the door later on.
^Using a second person, carefully tip
the appliance backwards and then fit
hinge pinbtogether with hinge bush
cfrom below into hinge plateeon
the left hand side.
^Refit coveraon the left.
^Place the lower door onto hinge pin
b.
^
Close the lower appliance door.
^
Fit hinge piniinto middle hinge
platekin the lower door.
^
Then fit the top door on middle hinge
pini.
Changing the door hinging
44
 
						

							^Fit hinge plateconto the opposite
side and secure it with screwsd.
If necessary drill pilot holes for the
screws or use a battery operated
screwdriver.
^Fit coversaandbto their opposite
sides.
^Align the door with the appliance
housing using the long slots in the
lower hinge plate. Then tighten the
screws.Refitting the handle:
Please make sure you follow the
instructions below carefully when
you refit the handle. The door seal
will be damaged if the handle is
fitted incorrectly.
^Loosely attach the handle to the
opposite side of the door with the two
front screwsb.
Mounting platecmust be positioned
on the side of the door so that when the
door isclosedit is flush with the side of
the appliance.
If this is not the case,
^
tighten both grub screwsawith a
suitable allen key until mounting plate
clines up correctly.
^
Then tighten all 4 fixing screwsb.
^
Slide the side section of the handle
dinto the guides on the mounting
plate until it clicks into place.
Changing the door hinging
45
 
						

							It is important to check that the side
section of the handleddoes not
come into contact with the door seal
when opening the door, as this
would damage the door seal
permanently.
If, after you have refitted the handle,
you find that the side section does
touch the door seal when the door is
opened:
Realign mounting platecwith grub
screwsauntil the mounting plate and
the side section of the handledare at
the correct angle and the side section
does not touch the door seal when the
door is opened.
Changing the door hinging
46
 
						

							The appliance doors can be aligned
with the housing at a later date.
In the following illustration the door
is not shown in the closed position to
make it easier to see what happens
next.
To align thelower dooruse the long
outer slots in the lower hinge plate:
^Remove centre screwafrom the
hinge plate.
^Slightly loosen both outer screwsb.
^
Align the door by sliding the hinge
plate to the left or right.
^
Then tighten screwsbagain. Screw
adoes not need to be refitted.To align theupper dooruse the long
outer slots in the middle hinge plate:
^Remove centre screwafrom the
hinge plate.
^Slightly loosen both outer screwsb.
^Align the door by sliding the hinge
plate to the left or right.
^Then tighten screwsbagain. Screw
adoes not need to be refitted.
Aligning the appliance doors
47
 
						

							aTop box
bAppliance
cHousing unit
dWall
The appliance can be installed in a
kitchen run. To match the height of the
rest of the kitchen, the appliance can
be fitted with a suitable top boxa.
A ventilation gap of at least 50 mm
depth must be allowed for behind the
appliance across the entire width of the
top box for air to circulate.
The cross section of the air outlet under
the room ceiling must be at least
300 cm
2to ensure that air can circulate
without hindrance. Otherwise the
appliance has to work harder, resulting
in an increase in electricity
consumption.
The air inlet and outlet must not be
covered or blocked in any way.
They should be dusted on a regular
basis.
When built into a kitchen run (max.
depth 580 mm) the appliance can be
installed directly next to a kitchen
furniture housing unit. The appliance
door will protrude in front of furniture
fronts at the sides by 34 mm and by
55 mm in the middle of the door. This
enables the doors to be opened and
shut without being obstructed.
When installednext to a wallda
distance of approx. 55 mm must be
maintained on the hinge side between
the walldand the applianceb,so
that the doors and the handles have
sufficient space for opening.
Building in the appliance
48
 
						

							49
 
						

							50