Miele Kfn 12923 Sd Operating And Installation Instructions

The appliance is supplied right-hand
hinged. If left-hand door hinging is
required, follow the instructions below.
To change the door hinging you will
need the following tools:
–a cross-slotted screwdriver,
–a flat-bladed screwdriver,
–a selection of Torx screwdrivers,
–a spanner.
Two people are needed for
changing the door hinging.
Removing the door handles:
^
Pull door handleatowards you. Side
sectionbslides back.
^
Pull side sectionbout of the guides
on the mounting plate.
^
Undo the 4 screws (Torx...

To remove the doors:
Make sure the door shelves are
empty.
^Close the upper door.
^Remove coveraby sliding it
forwards from the back and then
lifting it off.
^Remove coverbby pulling it
upwards.
Caution. The upper door is not
secure as soon as the upper hinge
plate is removed.
^
Loosen screwsdin upper hinge
platecand pull it upwards and off.
^
Carefully lift the upper door off and
place it to one side.
^
Carefully loosen coverefrom above
using a screwdriver and then take it
off together with retaining...

^Close the lower appliance door.
^Pull plastic coverhoff.
^Pull the middle hinge piniupwards
to remove it.
^Carefully lift the lower door off and
place it to one side.
^Pull coverjoff.
^Unscrew hinge platek, turn it
through 180° and fit it on the opposite
side.
^Turn plastic coverh180° and refit it
in the centre of hinge platek.
^
Refit coverjon the opposite side.^Remove caplfrom the bearing
bush in the door and refit on the
opposite side.
^Remove spring clampmfrom
underneath the door and fit it on the...

Changing over the doors:
^Remove coveraby pulling it
forwards.
^With the help of another person,
carefully tilt the appliance backwards
and pull hinge pinbout.
^Do not lose hinge bushc.
^Undo screwsdand take hinge plate
eoff.
^Remove coverfand fit it into the
holes on the opposite side.
^
Unscrew bearinggfrom hinge plate
eand screw it into the hole on the
other side of hinge platee.^Screw hinge plateeinto position on
the opposite side using the twoouter
long slots only. Do not use the middle
hole because...

^Fit hinge plateconto the opposite
side and secure it with screwsd.
If necessary drill pilot holes for the
screws or use a battery operated
screwdriver.
^Fit coversaandbto their opposite
sides.
^Align the door with the appliance
housing using the long slots in the
lower hinge plate. Then tighten the
screws.Refitting the handle:
Please make sure you follow the
instructions below carefully when
you refit the handle. The door seal
will be damaged if the handle is
fitted incorrectly.
^Loosely attach the...

It is important to check that the side
section of the handleddoes not
come into contact with the door seal
when opening the door, as this
would damage the door seal
permanently.
If, after you have refitted the handle,
you find that the side section does
touch the door seal when the door is
opened:
Realign mounting platecwith grub
screwsauntil the mounting plate and
the side section of the handledare at
the correct angle and the side section
does not touch the door seal when the
door is opened.
Changing...

The appliance doors can be aligned
with the housing at a later date.
In the following illustration the door
is not shown in the closed position to
make it easier to see what happens
next.
To align thelower dooruse the long
outer slots in the lower hinge plate:
^Remove centre screwafrom the
hinge plate.
^Slightly loosen both outer screwsb.
^
Align the door by sliding the hinge
plate to the left or right.
^
Then tighten screwsbagain. Screw
adoes not need to be refitted.To align theupper dooruse the long...

aTop box
bAppliance
cHousing unit
dWall
The appliance can be installed in a
kitchen run. To match the height of the
rest of the kitchen, the appliance can
be fitted with a suitable top boxa.
A ventilation gap of at least 50 mm
depth must be allowed for behind the
appliance across the entire width of the
top box for air to circulate.
The cross section of the air outlet under
the room ceiling must be at least
300 cm
2to ensure that air can circulate
without hindrance. Otherwise the
appliance has to work...

49
 

50