Miele Kf 9757 Id Operating And Installation Instructions

							. . . bars light up or flash in the
temperature displays.
Check the temperature displays about
6 hours after switching on the
appliance. Only temperatures within the
range the appliance can display will be
shown.
...F0toF5 in one of the
temperature displays appears.
There is a fault. Call the Service
Department.
. . . the Super freeze indicator light
and the temperature display are both
flashing at the same time.
There is a fault. Call the Service
Department.
. . . the Super freeze indicator light
does not light up, even though the
appliance is working.
The indicator light is defective. Call the
Service Department.
. . . you cannot switch the appliance
off.
The safety lock has been activated....nA appears in the freezer
section temperature display.
The freezer section temperature has
risen too high at some point during the
last couple of days because of a power
cut.
^Press the alarm off button whilst nA
is lit up in the display.
The temperature display will show the
warmest temperature recorded in the
freezer section during the power cut.
Depending on the temperature
displayed, you should check the
condition of food in the freezer. If it has
defrosted or started to defrost, check
that it is still safe to use and if so use it
as soon as possible. Defrosted food
may only be re-frozen after it has been
cooked.
The warmest temperature will show in
the display for about 1 minute. The
display will then revert to showing the
actual current temperature in the
freezer section.
At the end of a power cut, the
appliance will start operating again at
the last temperature setting selected.
Problem solving guide
41
 
						

							. . . the interior lighting in the
refrigerator section is not working.
Has the refrigerator door been left open
for too long? The lighting switches itself
off automatically after approx. 15
minutes.
If it also does not come on when the
door is opened briefly, but the
temperature display is working, then
the lighting is defective.
^Call the Service Department.
The LED lighting may only be repaired
or changed by a service technician.
Danger of injury and damage.
Should the cover be damaged or
need to be removed due to damage,
exercise caution.Never look at the
lighting with optical instruments
(magnifying glass or similar).
. . . the floor of the refrigerator is wet.
The drain hole is blocked.
^
Clean the condensate channel and
drain hole.
If you still cannot remedy the fault
having followed these suggestions,
please contact the Miele Service
Department.
To prevent unnecessary loss of
temperature, it is advisable not to
open the doors while waiting for the
appliance to be serviced.
Problem solving guide
42
 
						

							Normal noises What causes them
Brrrrr...Humming noise made by the motor (compressor). This noise can
get louder for brief periods when the motor is switching on.
Blubb, blubb....A gurgling noise can be heard when coolant is circulating
through the pipes.
Click....Clicking sounds are made when the thermostat switches the
motor on and off.
Sssrrrrr....On multi-zone and frost-free appliances you can sometimes just
hear the movement of air circulating inside the appliance.
Creak ...Creaking sounds can be heard when material inside the
appliance expands.
Remember that the noise of the compressor and the coolant circulating in the
system is unavoidable.
Noises that you can
easily rectifyWhat causes them, and what can you do about
them
Rattling, vibrating The appliance is uneven:Realign the appliance using a spirit
level, by raising or lowering the screw feet underneath the
appliance.
The appliance is touching another appliance or piece of
furniture:Move it away.
Drawers, baskets or shelves are unstable or sticking:Check
all removable items and refit them correctly.
Are any bottles or containers unstable or knocking against
each other?Separate them.
The transport cable clips are hanging loose at the back of
the appliance:Remove the clips.
Noises
43
 
						

							In the event of a fault which you cannot
correct yourself, or if the appliance is
under guarantee, please contact:
–your Miele Dealer
or
–Miele
(see back cover for contact details).
When contacting your Dealer or Miele,
please quote the model and serial
number of your appliance. This
information is given on the data plate
inside your appliance.
Please note that telephone calls may
be monitored and recorded for
training purposes.
N.B. A call-out charge will be applied
for service visits where the problem
could have been resolved as described
in these instructions.
Guarantee
For information on the appliance
guarantee specific to your country
please contact Miele. See back cover
for contact details.
In the U.K. your appliance is
guaranteed for 2 years from the date of
delivery. However, you must activate
your cover by calling 0845 365 6640 or
registering online at www.miele.co.uk.
After Sales / Guarantee
44
 
						

							Electrical connection U.K.
All electrical work should be carried out
by a suitably qualified and competent
person in strict accordance with current
local and national safety regulations
(BS 7671 in the UK).
The appliance is supplied with a mains
cable and moulded plug ready for
connection to an a.c. single phase
220-240 V 50 Hz supply.
Please ensure that the connection data
quoted on the data plate match the
household mains supply.
Connection should be made via a
suitable switched socket which is easily
accessible. For extra safety it is
advisable to protect the appliance with
a suitable residual current device
(RCD).
Do not connect the appliance to the
mains electricity supply by an extension
lead. Extension leads do not guarantee
the required safety of the appliance
(e.g. danger of overheating).
This appliance must not be connected
to the inverter of an autonomous power
supply, e.g. a solar power system.
When switching the appliance on, a
surge in power could trigger the safety
cut-out mechanism. This could damage
the electronic unit.
The appliance must not be used with
so-called energy saving devices. These
reduce the energy supply to the
appliance which could then become
too warm. Using such devices could
alter the specification of the product.Non-rewireable plugs (BS 1363)
The fuse cover must be re-fitted when
changing the fuse, and if the fuse cover
is lost, the plug must not be used until a
suitable replacement is obtained. The
colour of the correct replacement cover
is that of the coloured insert in the base
of the plug, or the colour that is
embossed in words in the base of the
plug (as applicable to the design of the
plug fitted).
Replacement fuses should be ASTA
approved to BS 1362 and have the
correct rating. Replacement fuses and
fuse covers may be purchased from
your local electrical supplier.
WARNING
THIS APPLIANCE MUST BE
EARTHED
Electrical connection
45
 
						

							To avoid a hazard due to instability
of the appliance, it must beinstalled
in accordance withthese
instructions.
Location
The appliance should be installed in a
dry, well ventilated room. The room
temperature should not go above or
below the climate range for which the
appliance is designed. The higher the
ambient temperature of the room, the
more energy the appliance requires to
operate.
It should not be installed where it is
exposed to direct sunlight or directly
adjacent to a heat-producing appliance
such as an oven or a radiator.
Important: tropical / humid
environments
During periods of high humidity,
some condensation may appear on
outside surfaces of cooling
appliances. This condensation will
disappear when humidity levels
drop. For prevention, it is advisable
to install the appliance with sufficient
ventilation in a dry and/or an
air-conditioned room.
Please ensure that doors are closing
and sealing properly.
Please ensure that the appliance is
installed in accordance with these
installation instructions and that the
handle is fitted correctly. Should you
require further assistance please
contact your Miele customer service
centre.Climate range
The appliance is designed for use
within certain climate ranges (ambient
temperatures) and should not be used
outside this range. The climate range of
the appliance is stated on the data
plate inside the appliance.
Climate range Ambient room
temperature
SN
N
ST
T
SN-ST
SN-T+10°C to +32°C
+16°C to +32°C
+16°C to +38°C
+16°C to +43°C
+10°C to +38°C
+10°C to +43°C
Operating in a room which is too cold
will cause the cooling system to switch
off for too long, causing the internal
temperature in the appliance to rise
with the risk of food deteriorating and
going off or frozen food defrosting.
Installation
46
 
						

							Ventilation
Air at the back of the appliance gets
warm. The appliance housing unit must
be constructed to allow sufficient space
for ventilation.
A ventilation gap of at least 38 mm
depth must be allowed for behind the
appliance for air to circulate.The air
inlet to the appliance is via the plinth in
the housing unit.
The cross-section of the air inlet and
outlet must be at least 200 cm
2to
ensure that air can circulate without
hindrance. Otherwise the appliance has
to work harder, resulting in an increase
in electricity consumption.
The air inlet and outlet must not be
covered or blocked in any way.
They should be dusted on a regular
basis.
Before installation
^Before installation, remove the cover
strip, sealing strip and other
accessories from the appliance and
from the external rear wall of the
appliance.
^
On no account should the spacers
be removed from the back of the
appliance. These ensure the gap
required between the back of the
appliance and the wall is maintained.^Remove any cable clips from the rear
of the appliance.
^Remove the red transport fixinga,
and use the stopper suppliedbto
plug the empty hole.
^Check that all parts at the back of the
appliance are unhindered. Carefully
remove any hindrance.Does your old appliance have
a different hinging
mechanism?
If your old appliance had a different
type of hinging, the furniture door can
still be used. Remove the old hinges
from the housing unit. They are no
longer required because the furniture
door is now fitted to the appliance door.
All the necessary parts are supplied or
can be ordered from the Miele Spare
Parts Department.
Installation
47
 
						

							Freezer section height Niche height
AB
KF 9757 iD549 1772 - 1788
Building-in dimensions
48
 
						

							The door hinges are set ex-works to
enable the doors to be opened wide.
However, if the opening angle of the
doors needs to be limited for any
reason, the hinges can be adjusted to
accommodate this.
–For example, if the appliance doors
hit an adjacent wall when opened,
the opening angle can be limited to
90°.
^Place the locking pins supplied for
limiting the door opening into the
hinges from above.
The door opening angle is now limited
to 90°.–If you would like the appliance doors
to be cushioned so that they open
more softly, the spring tension on the
doors can be adjusted.
To do this, use the allen key supplied to
adjust the door hinges.
aTo reduce the opening angle:
^
Turn the allen key clockwise.
This tightens the hinges and makes it
harder to open the door wide.
bTo open the door fully:
^
Turn the allen key anticlockwise.
Adjusting the door hinges
49
 
						

							Before building the appliance in, you
will need to decide on which side the
door is to be hinged. If left hand door
hinging is required, follow the
instructions below.
To change the door hinging you will
need the following tools:
–a cross-slotted screwdriver,
–a flat-bladed screwdriver,
–a selection of Torx screwdrivers,
–a spanner.
^Open both appliance doors.
^
Remove coversa,bandcand
capsdwith a screwdriver.
^
Slightly loosen fixing screwseat the
top, middle and bottom of the
appliance.
^
Push each of the doors outwards and
take them off their hinges.^Unscrew fixing screwsecompletely,
and loosely screw them in at the top,
middle and bottom on the opposite
side of the appliance.
If you have put locking pins into the
hinges to stop the door opening too far:
^Remove the locking pins from the top
of the hinges.
To remove the soft-close mechanism
^Place the doors with the outer side
downwards on a stable surface.
^
Using a screwdriver, carefully push
tension springaoutwards.
Warning. The soft-close mechanism
snaps shut when dismantled.
Danger of injury.
^
Unscrew mountingband pull
soft-close mechanismcdownwards
to remove it.
Changing the door hinging
50