Home > Miele > Fridge freezer > Miele Kf 8667 S Operating And Installation Instructions

Miele Kf 8667 S Operating And Installation Instructions

Here you can view all the pages of manual Miele Kf 8667 S Operating And Installation Instructions. The Miele manuals for Fridge freezer are available online for free. You can easily download all the documents as PDF.

Page 41

In the event of a fault which you cannot
correct yourself, or if the appliance is
under guarantee, please contact:
–your Miele Dealer
or
–the Miele Service Department (see
back cover for address).
When contacting your Dealer or the
Service Department, please quote the
model and serial number of your
appliance. This information is given on
the data plate.
Please note that telephone calls may
be monitored and recorded for
training purposes.
After sales service
41
 

Page 42

Electrical connection U.K.
All electrical work should be carried out
by a suitably qualified and competent
person in accordance with local and
national safety regulations.
The appliance is supplied with a mains
cable and moulded plug ready for
connection to an a.c. single phase
220-240 V 50 Hz supply.
The voltage and connected load are
given on the data plate. Please ensure
that these match the household mains
supply. The fuse rating is quoted on the
plug.
Connection should be made via a
suitable...

Page 43

Do not place any appliance which
gives off heat, such as a toaster or
microwave oven, on top of this
appliance, as this would increase
the appliance’s energy consumption.
Important: Appliances without side
wall heating must not be installed
side-by-side next to another
refrigerator or freezer. This could
cause condensation between the
two appliances and subsequent
damage.
Location
The appliance should be installed in a
dry, well-ventilated room.
The room temperature should not go
above or below the...

Page 44

Aligning the appliance
^To align the appliance adjust the feet
using the spanner supplied.
Installation
44
 

Page 45

The appliance is supplied right-hand
hinged. If left hand door hinging is
required, follow the instructions below.
Removing the door handles:
First the side sections of the handles
must be removed:
^Pull door handleatowards you. Side
sectionbslides back, creating a
gapdbetween side sectionband
mounting platec.
^
Place a suitable object (e.g. a spoon
handle) in gapd, and slowly lever
the handle towards the door.
Be careful not to let the spoon
handle slip, causing damage to the
appliance.
The side...

Page 46

^Open the upper door, and pull it
downwards and off. Take care not to
lose washera.
^Using a screwdriver remove covers
b.
^Unscrew upper hinge pincusing
the spanner supplied, and refit on the
opposite side.
^
Put coversbback on again from
behind, and then push them firmly
into place.^Exchange coverhin the middle of
the appliance with hinge brackete.
To do this:
Undo screwsi, pull coverhand
hinge bracketeoff to the side, turn
around, and refit and screw into
position on the opposite side.
^Pull bearing...

Page 47

In the following illustration the lower
door is not shown in the closed
position to make it easier to see
what happens next.
^Turn door supportbaround, pull
hinge pinaout, and refit on the
opposite side.
^
Fit both parts into hinge platef. To
do this push hinge pinathrough
hinge platefinto door supportb.
Swing the door support in, push
upwards and re-assemble with screw
c.
^
Align the lower door with the
appliance housing using the long slot
in hinge platef. Then tighten screw
c.
^
Refit plinth fasciad,...

Page 48

^Slide the side section of the handle
dinto the guides on the mounting
plate until it clicks into place.
It is important to check that the side
section of the handleddoes not
come into contact with the door seal
when opening the door, as this
would damage the door seal
permanently.
If they do come into contact, realign
mounting platecwith grub screwsa
until the mounting plate and the side
section of the handledare at the
correct angle, and the side section
does not touch the seal when the door
is...

Page 49

The appliance can be installed in a
kitchen run. To match the height of the
rest of the kitchen, the appliance can
be fitted with a suitable top boxa.
A ventilation gap of at least 50 mm
depth must be allowed for behind the
appliance and top box, if fitted, for air
to circulate.
A gap of at least 40 mm is required
between the top of the appliance (or
top box) and the ceiling to ensure that
air can circulate without hindrance.
Otherwise the appliance has to work
harder, resulting in an increase in...

Page 50

50
 
Start reading Miele Kf 8667 S Operating And Installation Instructions

Related Manuals for Miele Kf 8667 S Operating And Installation Instructions

All Miele manuals