Miele Kf 12823 Sd Operating And Installation Instructions

							Repairs to electrical appliances
should only be carried out by a
suitably qualified and competent
person in strict accordance with
current local and national safety
regulations. Repairs and other work
by unqualified persons could be
dangerous. The manufacturer
cannot be held liable for
unauthorised work.
What to do if...
. . . the appliance does not get cool.
^Check whether the appliance has
been switched on. The temperature
display must be lit up.
^Check that the plug is correctly
inserted into the socket and switched
on.
^Check that the fuse is not defective
and that the mains fuse has not
tripped. If it has, contact the Miele
Service Department.
. . . the temperature in the refrigerator
section or freezer section is too low.
^
Set a warmer temperature.
^
The Super freeze function is still on
and the Super freeze indicator light is
on.
The Super freeze function switches
itself off automatically after approx.
65 hours.
^
Check that the doors have been
closed properly.
^
Has a large amount of fresh food
been frozen at the same time?This makes the compressor run for
longer, causing the temperature in
the refrigerator section to fall
automatically.
. . . the compressor is switching in
too frequently and for too long.
^Check whether the ventilation gaps
have been covered over or become
dusty.
^Check whether the metal grille (heat
exchanger) at the back of the
appliance has become too dusty.
^The doors have been opened too
frequently, or a large amount of fresh
food has been put in at once for
freezing.
^Check that the doors have been
closed properly.
. . . the frozen food is thawing
because the freezer section is too
warm.
^
Is the room temperature lower than
the ambient temperature for which
the appliance is designed?
If so, raise the temperature of the
room.
Operating in a room which is too cold
will cause the cooling system to switch
off for too long, causing the freezer
section to become too warm.
Problem solving guide
31
 
						

							. . . food has frozen together.
Use a blunt instrument, e.g. a spoon
handle or plastic scraper, to prise it
apart carefully.
. . . the door to the freezer section
will not open because it has been
opened and closed too many times in
succession.
This is not a fault. The suction caused
by opening and closing the door is
preventing the door from opening. Wait
a few minutes and then try again. It
should now open without force.
. . the alarm sounds.
Has one of the the appliance doors
been open for longer than 60 seconds?
^Close the door.
. . . the alarm sounds and the freezer
section temperature display flashes.
The freezer section temperature has
risen above the set temperature
because
^
the freezer section door has been
opened too frequently, or large
amounts of fresh food have been put
in at once for freezing.
^
the ventilation gaps are blocked.
Once the problem has been resolved
the freezer section temperature display
will light up constantly and the alarm
will stop.. . . the Super freeze indicator light
and one of the temperature display
lights are flashing at the same time.
There is a fault. Call the Service
Department.
. . . the interior lighting in the
refrigerator section is not working.
^Was the refrigerator section door left
open for too long? The lighting
switches itself off automatically after
approx. 15 minutes.
If this is not the case, then the lamp is
defective:
^Disconnect the appliance from the
mains. Switch off at the wall and
withdraw the plug from the socket, or
disconnect the mains fuse or remove
the screw-out fuse in countries where
this is applicable.
^
Grip the lamp coveraat the front
and unhook it at the back.
^
Unscrew the lampband replace it
with a new one.
Problem solving guide
32
 
						

							Lamp specification:
220 - 240 V, E 14 fitting
See the old lamp for the Wattage
required.
^Replace the lamp covera.
. . . the floor of the refrigerator is wet.
The drain hole is blocked.
^Clean the condensate channel and
drain hole.
If you still cannot remedy the fault
having followed these suggestions,
please contact the Miele Service
Department.
To prevent unnecessary loss of
temperature it is advisable not to
open the doors while waiting for the
appliance to be serviced.
Problem solving guide
33
 
						

							Normal noises What causes them
Brrrrr...Humming noise made by the motor (compressor). This noise can
get louder for brief periods when the motor is switching on.
Blubb, blubb....A gurgling noise can be heard when coolant is circulating
through the pipes.
Click....Clicking sounds are made when the thermostat switches the
motor on and off.
Sssrrrrr....On multi-zone and frost-free appliances you can sometimes just
hear the movement of air circulating inside the appliance.
Remember that the noise of the compressor and the coolant circulating in the
system is unavoidable.
Noises that you can
easily rectifyWhat causes them, and what can you do about
them?
Rattling, vibrating The appliance is uneven:Realign the appliance using a spirit
level, by raising or lowering the screw feet underneath the
appliance.
The appliance is touching another appliance or piece of
furniture:Move it away.
Drawers, baskets or shelves are unstable or sticking:Check
all removable items and refit them correctly.
Are any bottles or containers unstable or knocking against
each other?Separate them.
The transport cable clips are hanging loose at the back of
the appliance:Remove the clips.
Noises
34
 
						

							In the event of a fault which you cannot
correct yourself, or if the appliance is
under guarantee, please contact:
–your Miele Dealer
or
–Miele
(see back cover for contact details).
When contacting your Dealer or Miele,
please quote the model and serial
number of your appliance. This
information is given on the data plate
inside your appliance.
Please note that telephone calls may
be monitored and recorded for
training purposes.
N.B. A call-out charge will be applied
for service visits where the problem
could have been resolved as described
in these instructions.
Guarantee
For information on the appliance
guarantee specific to your country
please contact Miele. See back cover
for contact details.
In the U.K. your appliance is
guaranteed for 2 years from the date of
delivery. However, you must activate
your cover by calling 08706 080028 or
registering online at www.miele.co.uk.
After Sales / Guarantee
35
 
						

							Electrical connection U.K.
All electrical work should be carried out
by a suitably qualified and competent
person in strict accordance with current
local and national safety regulations
(BS 7671 in the UK).
The appliance is supplied with a mains
cable and moulded plug ready for
connection to an a.c. single phase
220-240 V 50 Hz supply.
Please ensure that the connection data
quoted on the data plate match the
household mains supply.
Connection should be made via a
suitable switched socket which is easily
accessible. For extra safety it is
advisable to install a suitable residual
current device (RCD).
Do not connect the appliance to the
mains electricity supply by an extension
lead. Extension leads do not guarantee
the required safety of the appliance
(e.g. danger of overheating).
The appliance must not be connected
to an inverter and must not be used
with a plug adapter as these can cause
damage to the appliance’s electronic
unit.Non-rewireable plugs (BS 1363)
The fuse cover must be re-fitted when
changing the fuse, and if the fuse cover
is lost, the plug must not be used until a
suitable replacement is obtained. The
colour of the correct replacement cover
is that of the coloured insert in the base
of the plug, or the colour that is
embossed in words in the base of the
plug (as applicable to the design of the
plug fitted).
Replacement fuses should be ASTA
approved to BS 1362 and have the
correct rating. Replacement fuses and
fuse covers may be purchased from
your local electrical supplier.
WARNING
THIS APPLIANCE MUST BE
EARTHED
Electrical connection
36
 
						

							Do not place any appliance which
gives off heat, such as a toaster or
microwave oven, on top of this
appliance, as this would increase
the appliances energy
consumption.
This appliance must not be installed
directly next to another refrigerator
or freezer.
It does not have side-wall heating,
so installation next to another
refrigerator or freezer could cause a
build-up of condensation between
them.
Further information is available from
your dealer.
Location
This appliance should be installed in a
dry, well-ventilated room. It should not
be installed where it is exposed to
direct sunlight or directly adjacent to a
heat-producing appliance such as an
oven or a radiator. The room
temperature should not go above or
below the climate range for which the
appliance is designed. The higher the
ambient temperature of the room, the
more energy the appliance requires to
operate.
Important: tropical / humid
environments
During periods of high humidity,
some condensation may appear on
outside surfaces of cooling
appliances. This condensation will
disappear when humidity levels
drop. For prevention, it is advisable
to install the appliance with sufficient
ventilation in a dry and/or an
air-conditioned room.
Please ensure that doors are closing
and sealing properly.
Please ensure that the appliance is
installed in accordance with these
installation instructions and that the
handle is fitted correctly. Should you
require further assistance please
contact your Miele customer service
centre.
Installation
37
 
						

							Climate range
The appliance is designed for use
within certain climate ranges (ambient
temperatures), and should not be used
outside this range. The climate range of
the appliance is stated on the data
plate inside the appliance.
Climate range Ambient room
temperature
SN
N
ST
T
SN-ST
SN-T+10°C to +32°C
+16°C to +32°C
+16°C to +38°C
+16°C to +43°C
+10°C to +38°C
+10°C to +43°C
Operating in a room which is too cold
will cause the cooling system to switch
off for too long, causing the internal
temperature in the appliance to rise
with the risk of frozen food deteriorating
and going off.
Ventilation
Air at the back of the appliance gets
warm. To ensure sufficient ventilation,
the ventilation gaps must not be
covered over. The air inlet and outlet
must not be covered or blocked in any
way. They should be dusted on a
regular basis.
Installation
^Remove the cable clip from the back
of the appliance.
^Check that all parts at the back of the
appliance are unhindered. Carefully
remove any hindrance.
^Carefully push the appliance into
position with the back against the
wall.
Aligning the appliance
^To align the appliance, adjust the feet
using the spanner supplied.
^
Also unscrew supportafrom the
bearing block, to level the appliance
door.
Installation
38
 
						

							Appliance dimensions
ABC
KFN 12823 SD1820 mm 600 mm 630 mm
KFN 12923 SD,
KFN 12924 SD2010 mm 600 mm 630 mm
Installation
39
 
						

							The appliance is supplied right-hand
hinged. If left-hand door hinging is
required, follow the instructions below.
To change the door hinging you will
need the following tools:
–a cross-slotted screwdriver,
–a flat-bladed screwdriver,
–a selection of Torx screwdrivers,
–a spanner.
Two people are needed for
changing the door hinging.
Removing the door handles:
^
Pull door handleatowards you. Side
sectionbslides back.
^
Pull side sectionbout of the guides
on the mounting plate.
^
Undo the 4 screws (Torx 15) in the
mounting plate, and remove the
handle.
^
Remove the cover caps from the
opposite side, and fit them into the
empty holes.
Changing the door hinging
40