Home > Miele > Fridge freezer > Miele Kdn 9713 Id Operating And Installation Instructions

Miele Kdn 9713 Id Operating And Installation Instructions

Here you can view all the pages of manual Miele Kdn 9713 Id Operating And Installation Instructions. The Miele manuals for Fridge freezer are available online for free. You can easily download all the documents as PDF.

Page 31

Repairs to electrical appliances
should only be carried out by a
suitably qualified and competent
person in strict accordance with
current local and national safety
regulations. Repairs and other work
by unqualified persons could be
dangerous. The manufacturer
cannot be held liable for
unauthorised work.
Ensure that current is not supplied to
the appliance until after
maintenance or repair work has
been carried out.
Some minor problems can be corrected
without contacting the Miele Service
Department....

Page 32

. . . the frozen food is thawing
because the freezer section is too
warm.
^Is the room temperature lower than
the ambient temperature for which
the appliance is designed?
If so, raise the temperature of the
room.
Operating in a room which is too cold
will cause the cooling system to switch
off for too long causing the freezer
section to become too warm.
. . . food has frozen together.
Use a blunt instrument, e.g. a spoon
handle or plastic scraper, to prise it
apart carefully.
. . . the alarm sounds and...

Page 33

^Unscrew the lamp. This requires
some strength, as the safety catch
needs to be released.
^Change the lamp.
Lamp specification:
220 - 240 V, E 14 fitting
See the old lamp for the Wattage
required.
^Screw the new lamp into the
connection. Make sure the safety
catch is correctly fitteda.
^Replace the lamp cover, and click it
into place at the sides.
. . . the floor of the refrigerator is wet.
The drain hole is blocked.
^
Clean the condensate channel and
drain hole.
If you still cannot remedy the fault...

Page 34

Normal noises What causes them
Brrrrr...Humming noise made by the motor (compressor). This noise can
get louder for brief periods when the motor is switching on.
Blubb, blubb....A gurgling noise can be heard when coolant is circulating
through the pipes.
Click....Clicking sounds are made when the thermostat switches the
motor on and off.
Sssrrrrr....On multi-zone and frost-free appliances you can sometimes just
hear the movement of air circulating inside the appliance.
Creak ...Creaking sounds can be...

Page 35

In the event of a fault which you cannot
correct yourself, or if the appliance is
under guarantee, please contact:
–your Miele Dealer
or
–Miele
(see back cover for contact details).
When contacting your Dealer or Miele,
please quote the model and serial
number of your appliance. This
information is given on the data plate
inside your appliance.
Please note that telephone calls may
be monitored and recorded for
training purposes.
N.B. A call-out charge will be applied
for service visits where the problem...

Page 36

Electrical connection U.K.
All electrical work should be carried out
by a suitably qualified and competent
person in strict accordance with current
local and national safety regulations
(BS 7671 in the UK).
The appliance is supplied with a mains
cable and moulded plug ready for
connection to an a.c. single phase
220-240 V 50 Hz supply.
Please ensure that the connection data
quoted on the data plate match the
household mains supply.
Connection should be made via a
suitable switched socket which is easily...

Page 37

This appliance must be built in,
otherwise it could tip up.
Location
This appliance should be installed in a
dry, well-ventilated room. It should not
be installed where it is exposed to
direct sunlight or directly adjacent to a
heat-producing appliance such as an
oven or a radiator. The room
temperature should not go above or
below the climate range for which the
appliance is designed. The higher the
ambient temperature of the room, the
more energy the appliance requires to
operate.
Important: tropical /...

Page 38

The ventilation gaps must not be
covered or blocked in any way.
They should be dusted on a regular
basis.
Before installing the appliance
^Before installation remove the cover
strip, sealing strip and other
accessories from inside the
appliance and from the external rear
wall of the appliance.
^Do not remove the spacers from the
back of the appliance. These ensure
the gap required between the back
of the appliance and the wall is
maintained.
^
Remove any cable clips from the
back of the appliance.
^...

Page 39

Freezer section height Niche height
AB
KDN 9713 iD
KDN 9713 i-1669 1772 - 1788
Building-in dimensions
39
 

Page 40

Before building the appliance in, you
will need to decide on which side the
doors are to be hinged. If left hand door
hinging is required, follow the
instructions below.
To change the door hinging, you will
need various sizes ofTorx
screwdriversand aslotted
screwdriver.
^Open both appliance doors.
^
Pull off coversa,bandcand caps
d.
^
Unscrew hinge pinefrom the top
appliance door.
^
Tilt the top door, and lift it up and off.
^
Then remove hinge pinffrom the
middle of the appliance.Take care when doing so...
Start reading Miele Kdn 9713 Id Operating And Installation Instructions

Related Manuals for Miele Kdn 9713 Id Operating And Installation Instructions

All Miele manuals