Miele K 9758 Idf Operating And Installation Instructions

In the event of a fault which you cannot
correct yourself, or if the appliance is
under guarantee, please contact:
–your Miele Dealer
or
–the Miele Service Department
(see back cover for contact details).
When contacting your Dealer or Miele,
please quote the model and serial
number of your appliance. This
information is given on the data plate
inside your appliance.
Please note that telephone calls may
be monitored and recorded for
training purposes.
Guarantee
For information on the appliance
guarantee...

Electrical connection U.K.
All electrical work should be carried out
by a suitably qualified and competent
person in strict accordance with current
local and national safety regulations
(BS 7671 in the UK).
The appliance is supplied with a mains
cable and moulded plug ready for
connection to an a.c. single phase
220-240 V 50 Hz supply.
Please ensure that the connection data
quoted on the data plate match the
household mains supply.
Connection should be made via a
suitable switched socket which is easily...

This appliance must be built in,
otherwise it could tip up.
Location
The appliance should be installed in a
dry, well-ventilated room.
The room temperature should not go
above or below the climate range for
which the appliance is designed.
The higher the ambient temperature of
the room, the more energy the
appliance requires to operate.
It should not be installed where it is
exposed to direct sunlight or directly
adjacent to a heat-producing appliance
such as an oven or a radiator.
Climate range
The...

Before installation
^Before installation remove the cover
strip, sealing strip and other
accessories from the appliance and
from the external rear wall of the
appliance.
^On no account should the spacers
be removed from the back of the
appliance. These ensure the gap
required between the back of the
appliance and the wall is maintained.
^Remove any cable clips from the rear
of the appliance.
^Check that all parts at the back of the
appliance are unhindered. Carefully
remove any hindrance.
Does your old...

Niche height [mm]
A
K 9758 iDF1772 - 1788
Building-in dimensions
45
 

The door hinges are set ex-works to
enable the door to be opened wide.
However, if the opening angle of the
door needs to be limited for any reason,
the hinge can be adjusted to
accommodate this.
–For example, if the appliance door
hits an adjacent wall when opened,
the opening angle can be limited to
90°.
^Place the locking pins supplied for
limiting the door opening into the
hinges from above.
The door opening angle is now limited
to 90°.–If you would like the appliance door
to be cushioned so that it...

Before building the appliance in, you
will need to decide on which side the
door is to be hinged. If left hand door
hinging is required, follow the
instructions below.
To change the door hinging, you will
need various sizes ofTorx
screwdrivers,aslotted
screwdriverand aspanner.
Appliance door
^Open the appliance door.
^
Remove coversa,bandcwith a
screwdriver.
^
Loosen fixing screwsdslightly.
^
Slide the door outwards and lift it off
e.
^
Unscrew the fixing screwsd
completely, and loosely screw themin at...

Do not separate the soft-close
mechanism from the ball joint. This
would damage the mechanism.
^Stand the appliance door up, and
slacken the hinges at the front (the
hinges remain open).
^Remove screwsa, and place the
stoppers suppliedcin the empty
holes.
Do notclose up the hinges. Danger
of injury.
^
Replace the hinges in their diagonally
opposite cornersb.
^
Use a powered screwdriver to secure
the hinges; screwsaare
self-tapping.To secure the soft-close mechanism
^Place the door with the outer side...

^Push the appliance door onto the
pre-fitted screws, and then tighten
the screws.
^Replace coversa,bandc.
^
Replace the locking pins into the top
of the hinges to prevent the door
opening too far.
Freezer compartment door
^Lower the cover on hinge platea.
^Unscrew hinge plateb, and remove
freezer compartment doorc
together with the hinge plate.
^Unscrew door catchd.
^
Screw door catchdinto place on
the opposite side, having turned it by
180 °.
^
Fit the freezer compartment doorc
in position at the tope,...

All fitting instructions given are for a
right hand hingedappliance. If you
have converted the appliance to left
hand hinging you will need to adapt
these instructions accordingly.
To install the appliance you will need
the following:
–a cross-slotted screwdriver,
–a selection of Torx screwdrivers,
–a hexagon spanner.
Weight of the furniture door
Before fitting a furniture door, ensure
that the weight of the door does not
exceed the maximum permitted:
ApplianceMaximum weight of
furniture door in kg
K...