Miele K 9752 Id Operating And Installation Instructions

In the event of a fault which you cannot
correct yourself, or if the appliance is
under guarantee, please contact:
–your Miele Dealer
or
–Miele
(see back cover for contact details).
When contacting your Dealer or Miele,
please quote the model and serial
number of your appliance. This
information is given on the data plate
inside your appliance.
Please note that telephone calls may
be monitored and recorded for
training purposes.
N.B. A call-out charge will be applied
for service visits where the problem...

Electrical connection U.K.
All electrical work should be carried out
by a suitably qualified and competent
person in strict accordance with current
local and national safety regulations
(BS 7671 in the UK).
The appliance is supplied with a mains
cable and moulded plug ready for
connection to an a.c. single phase
220-240 V 50 Hz supply.
Please ensure that the connection data
quoted on the data plate match the
household mains supply.
Connection should be made via a
suitable switched socket which is easily...

This appliance must be built in,
otherwise it could tip up.
Location
This appliance should be installed in a
dry, well-ventilated room. It should not be
installed where it is exposed to direct
sunlight or directly adjacent to a
heat-producing appliance such as an
oven or a radiator. The room temperature
should not go above or below the climate
range for which the appliance is
designed. The higher the ambient
temperature of the room, the more
energy the appliance requires to operate.
Important: tropical /...

Before installation
^Before installation remove the cover
strip, sealing strip and other
accessories from inside the
appliance and from the external rear
wall of the appliance.
^Do notremove the following from the
back of the appliance:
– The spacers.
These ensure the gap required
between the back of the appliance
and the wall is maintained.
– Depending on model, the bags
located between the back of the
appliance and the metal grille (heat
exchanger). They are important for
the correct functioning of...

Stainless steel front
(depending on model)
If the old appliance had a different type
of hinging, or if you cannot or do not
wish to reuse the old furniture door a
stainless steel front can be fitted
instead.
This is available from your dealer or the
Miele Spare Parts Department.
Installation
35
 

Niche height (mm)
A
K 9552 iD (-1)1397 - 1413
K 9752 iD (-1)1772 - 1788
Building-in dimensions
36
 

The door hinges are set ex-works to
enable the door to be opened wide.
However, if the opening angle of the
door needs to be limited for any reason,
the hinge can be adjusted to
accommodate this.
–For example, if the appliance door
hits an adjacent wall when opened,
the opening angle can be limited to
90°.
^Place the locking pins supplied for
limiting the door opening into the
hinges from above.
The door opening angle is now limited
to 90°.–If you would like the appliance door
to be cushioned so that it...

Before building the appliance in, you
will need to decide on which side the
door is to be hinged. If left hand door
hinging is required, follow the
instructions below.
To change the door hinging you will
need the following tools:
–a cross-slotted screwdriver,
–a screwdriver,
–a selection of Torx screwdrivers,
–a spanner.
Appliance door
^
Open the appliance door.
^
Remove coversa,bandcwith a
screwdriver.
^
Loosen fixing screwsdat the top
and the bottom slightly.^Slide the door outwards and lift it off
e....

^Unscrew mountingband pull
soft-close mechanismcdownwards
to remove it.
^Undo ball jointdusing a spanner
and remove it.
^Stand the appliance door up, and
loosen the hinges at the front (the
hinges remain open).
^
Remove screwsa, and use the
stoppers suppliedcto plug the
empty holes.
Do notclose up the hinges. Danger
of inury.^Replace the hinges in their diagonally
opposite cornersb.
^Use a powered screwdriver to secure
the hinges; screwsaare
self-tapping.
To secure the soft-close mechanism
^Place the...

^Push the appliance door onto the
pre-fitted screws, and then tighten
the screws.
^Replace coversa,bandc.
^
Replace the locking pins into the top
of the hinges to prevent the doors
opening too far.
Changing the door hinging
40