Miele K 9214 If Operating And Installation Instructions

							Freezer compartment door
^Lower the cover on hinge platea.
^Unscrew hinge plateb, and remove
freezer compartment doorc
together with the hinge plate.
^Unscrew door catchd.
^
Screw door catchdinto place on
the opposite side, having turned it by
180 °.
^
Fit the freezer compartment doorc
in position at the tope, then tighten
the hinge plate securelyb.
^
Close the cover on hinge platea.
^
Plug the holes with stoppersf.
Changing the door hinging
41
 
						

							All building-in instructions given are
for aright hand hingedappliance.
If you have converted the appliance
to left hand hinging you will need to
adapt these instructions
accordingly.
Building into a peninsular run
When built into a peninsular run, the
rear of the building in niche must be
fitted with a kitchen furniture panel.
Aligning the housing unit
Before installing the appliance, the
housing unit must be carefully aligned
using a spirit level. The housing unit
corners must be at right angles, as
otherwise the appliance furniture door
will not align correctly with the 4
corners of the unit. Align the furniture
door with the hinges.
Preparing the appliance
^Slide cover stripainto the holder as
shown, with the bumps facing
downwards. The bumps will fit into
keyhole slotsb. The cover strip is
then flush with the side of the
appliance on which the door is
openedc.
Building in the appliance
42
 
						

							Building in the appliance
^Remove panela.
^Secure bracketbwith screwsc
(4.8 x 16 mm).
^
Attach sealing stripdto the door
opening side so that it sits flush at the
front with the side of the appliance. If
necessary the sealing strip can be
trimmed to size along the lower edge
of bracketb.
^
Push the appliance into its housing
unit.
When doing this, make sure that the
mains cable does not get trapped.
^
Push in the appliance until the front
edges of bracketband hinge plates
eandfare flush with the front
edge of the housing.^Align the appliance height from above
on both sides using adjusting screw
g.
Building in the appliance
43
 
						

							Securing the appliance and
fitting the furniture door
^Push the appliance against the
housing wall on the side on which the
door opens so that the sealing strip is
pressed into the housing wallh.
^
Secure the appliance at the top with
screwi(4 x 19 mm) into bracketb,
pushing the appliance against the
furniture wall as you do so. Then
secure it at the bottom with screwsj
(4 x 36 mm) through the adjusting
screws in the hinge plates to the
housing.
^
Tighten all the screws.^If necessary, align cover stripkby
pushing it parallel to the top of the
unit - it should not protrude.
^Fold in the side section of bracketb.
^Replace covera, and cap all the
holes with stopperslandm.
^Secure door fixingsnto the
appliance door with screwo
(3.9 x 9.5 mm), to suit the position of
the handle,
Very large doors will require several
door fixings.
^Open the door right out, and push
fixing guidespinto door fixingsn.
^Position the furniture door onto the
appliance door, and secure fixing
guidespto the furniture door using
screwsq(4 x 14 mm). Maintain a
distance d (= the thickness of the
housing unit walls) between the edge
of the appliance door and outer edge
of the furniture door.
^
Align the door fixing so that the
furniture door on the side with the
handle does not lie against the
housing unit wall when the door is
shut. Aminimum distance of 1 mm
rmust be maintained. This is vital
for the longterm effectiveness of the
insulation.
Building in the appliance
44
 
						

							45
 
						

							46
 
						

							47
 
						

							Alteration rights reserved / 4710
K 9212 i, K 9214 iF, K 9412 i, K 9414 iFM.-Nr. 07 923 420 / 00