Miele K 14827 Operating And Installation Instructions

							The active charcoal filters should be
changed approx. every 6 months.
When the Change active charcoal filter
indicator lights up red, the active
charcoal filters need to be changed.
To change the active charcoal
filters
^Pull the active charcoal filter holder
upwards to remove it from the shelf.
^
Take out the two filters and fit the new
filters into the holder with the
protruding cloth edge facing
downwards.
^
Place the holder in the middle of the
raised edge at the back of the shelf,
so that it clicks into position.To confirm the filters have been
changed
^Touch the Change active charcoal
filter indicator for approx. 2 seconds.
The indicator light will go out, and the
counter will be reset.
To delay changing the active
charcoal filters
If you do not have new active charcoal
filters, you can order them from your
Miele Chartered Agent or from the
Miele Spare Parts Department.
You can switch off the Change active
charcoal filter indicator early if you
would prefer not to have the red
indicator showing.
^
Touch the Change active charcoal
filter indicator for approx. 2 seconds.
The Change active charcoal filter
indicator will go out.
Active charcoal filters
31
 
						

							If you have delayed changing the
active charcoal filters and the indicator
is not lit up, you will need to reset the
counter when you replace the active
charcoal filters via the settings mode.
^Touch and leave your finger on the
sensor.
^At the same time, briefly touch the
On/Off sensor (without letting go of
thesensor).
^Leave your finger on thesensor for
another 5 seconds untilcappears in
the display.
^Touch thesensor repeatedly until
^appears in the display.
^
Touch the On/Off sensor.
^
Touch thesensor repeatedly until
^2appears in the display.
^
Touch the On/Off sensor for approx.
2 seconds to confirm.
The counter is now reset.
^
Touch thesensor repeatedly until
cappears in the display.
^
Touch the On/Off sensor.
You have now left the settings mode.Useful tip:
When you are storing foods with a
strong smell (such as ripe cheeses),
–place the holder containing the
active charcoal filters on the shelf
where the food is going to be stored,
–change the active charcoal filters
early if required (remembering to
reset the counter),
–and place more active charcoal
filters (in holders) in the appliance.
Active charcoal filters and holders
can be obtained from your Miele
Chartered Agent or from the Miele
Spare Parts Department.
Active charcoal filters
32
 
						

							Repairs to electrical appliances
should only be carried out by a
suitably qualified and competent
person in strict accordance with
current local and national safety
regulations. Repairs and other work
by unqualified persons could be
dangerous. The manufacturer cannot
be held liable for unauthorised work.
What to do if...
. . . the appliance does not get cool.
^Check whether the appliance has
been switched on. The temperature
display must be lit up.
^Check that the plug is correctly
inserted into the socket and switched
on.
^Check that the fuse is not defective
and that the mains fuse has not
tripped. If it has, contact the Miele
Service Department.
. . . the temperature in the refrigerator
is too low.
^
Select a warmer temperature.
^
The SuperCool function is still
switched on. SuperCool only
switches itself off after 6 hours.
. . the alarm sounds.
Has the appliance door been open for
longer than 2 minutes?
^
Close the door.. . . the compressor is switching in
too frequently and for too long.
^Check whether the ventilation gaps
have been covered over or become
dusty.
^Check whether the metal grille (heat
exchanger) at the back of the
appliance has become too dusty.
^The door has been opened too
frequently, or a large amount of food
has been put in at once.
^Check that the door has been closed
properly.
. . . the compressor runs
continuously.
To save energy, the compressor runs at
a lower speed, but for longer, when
less cooling is required.
. . . the interior lighting is not
working.
^
Was the door left open for too long?
The lighting switches itself off
automatically after approx.
15 minutes.
If this is not the case, then the LED
lighting is defective.
^
Call the Service Department.
The LED lighting may only be repaired
or changed by a service technician.
Danger of injury and damage.
Problem solving guide
33
 
						

							Should the cover be damaged or
need to be removed due to damage,
exercise caution.Never look at the
lighting with optical instruments
(magnifying glass or similar).
. . . the change the active charcoal
filter indicator is red.
^Replace the active charcoal filters.
You can order replacement filters via
your Miele Chartered Agent or the Miele
Spare Parts Department.
..._F shows in the temperature
display.
There is a fault. Call the Service
Department.
...dn appears in the temperature
display.
The demonstration function is activated.
^Call the Service Department.
. . . you cannot switch the appliance
off.
The safety lock has been activated.
. . . the floor of the refrigerator is wet.
The drain hole is blocked.
^
Clean the condensate channel and
drain hole.If you still cannot remedy the fault
having followed these suggestions,
please contact the Miele Service
Department.
To prevent unnecessary loss of
temperature it is advisable not to
open the door while waiting for the
appliance to be serviced.
Problem solving guide
34
 
						

							Normal noises What causes them
Brrrrr...Humming noise made by the motor (compressor). This noise can
get louder for brief periods when the motor is switching on.
Blubb, blubb....A gurgling noise can be heard when coolant is circulating
through the pipes.
Click....Clicking sounds are made when the thermostat switches the
motor on and off.
Sssrrrrr....On multi-zone and frost free appliances you can sometimes just
hear the movement of the fan inside the appliance.
Remember that the noise of the compressor and the coolant circulating in the
system is unavoidable.
Noises that you can
easily rectifyWhat causes them, and what can you do about
them?
Rattling, vibrating The appliance is uneven: Realign the appliance using a spirit
level by raising or lowering the screw feet underneath the
appliance.
The appliance is touching another appliance or piece of
furniture:Move it away.
Drawers, baskets or shelves are unstable or sticking:Check
all removable items and refit them correctly.
Are any bottles or containers unstable or knocking against
each other?Separate them.
The transport cable clips are hanging loose at the back of
the appliance:Remove the clips.
Noises
35
 
						

							In the event of a fault which you cannot
correct yourself, or if the appliance is
under guarantee, please contact:
–your Miele Chartered Agent
or
–Miele.
You will find the address and
telephone number of Miele on the
back cover of the manual.
When contacting your Chartered Agent
or Miele, please quote the model and
serial number of your appliance. This
information is given on the data plate
inside your appliance.
After Sales
36
 
						

							Electrical connection
All electrical work should be carried out
by a suitably qualified and competent
person in strict accordance with current
local and national safety regulations.
The appliance is supplied with a mains
cable and moulded plug ready for
connection to an AC single phase
220-240 V 50 Hz supply.
The voltage and frequency are given on
the data plate. Please ensure that these
match the household mains supply. The
fuse rating is quoted on the plug.
Connection should be made via a
suitable switched socket which is easily
accessible. For extra safety it is
advisable to install a suitable residual
current device (RCD).
Do not connect the appliance to the
mains electricity supply by an extension
lead. Extension leads do not guarantee
the required safety of the appliance
(e.g. danger of overheating).
The appliance must not be connected
to an inverter and must not be used
with a plug adapter as these can cause
damage to the appliance’s electronic
unit.
WARNING
THIS APPLIANCE MUST BE
EARTHED
Electrical connection
37
 
						

							Do not place any appliance which
gives off heat, such as a toaster or
microwave oven, on top of this
appliance, as this would increase
the appliances energy
consumption.
Side-by-side installation
To avoid a build-up of condensation
and resultant damage, refrigerators and
freezers should not generally be
installed side by side next to other such
appliances.
However, some appliances have
side-wall heating making them suitable
for side-by-side installation with this
refrigerator.
Your Miele Chartered Agent will be
able to advise you on which models
are suitable.
^Follow the instructions for the other
appliance on how to install the two
appliances side by side.
Location
This appliance should be installed in a
dry, well-ventilated room. It should not
be installed where it is exposed to
direct sunlight or directly adjacent to a
heat-producing appliance such as an
oven or a radiator. The room
temperature should not go above or
below the climate range for which the
appliance is designed. The higher the
ambient temperature of the room, the
more energy the appliance requires to
operate.Climate range
The appliance is designed for use
within certain climate ranges (ambient
temperatures), and should not be used
outside this range. The climate range of
the appliance is stated on the data
plate inside the appliance.
Climate range Ambient room
temperature
SN
N
ST
T
SN-ST
SN-T+10°C to +32°C
+16°C to +32°C
+16°C to +38°C
+16°C to +43°C
+10°C to +38°C
+10°C to +43°C
Operating in a room which is too cold
will result in the cooling system
switching off for too long, causing the
internal temperature in the appliance to
rise with the risk of food deteriorating
and going off.
Ventilation
Air at the back of the appliance gets
warm. To ensure sufficient ventilation,
the ventilation gaps must not be
covered over. The air inlet and outlet
must not be covered or blocked in any
way. They should be dusted on a
regular basis.
Installation
38
 
						

							Installation
^Remove the cable clip from the back
of the appliance.
^Check that all parts at the back of the
appliance are unhindered. Carefully
remove any hindrance.
^Carefully push the appliance into
position with the back against the
wall.
Aligning the appliance
^To align the appliance, adjust the
front feet using the spanner supplied.
^
If necessary, also align the two rear
adjusting devicesausing socket
wrenchb.
Turn the adjusting device clockwise
to raise the appliance up at the back.^Unscrew footcfrom the hinge plate,
to level the appliance door.
Installation
39
 
						

							Appliance dimensions
ABC
K 14827 SD ed1852 mm 600 mm 630 mm
Installation
40