Miele K 12820 Sd Manual

							Remove cap	from the bearing
bush in the door and refit on the
opposite side.

Using a screwdriver, remove spring
clamp
from underneath the door
and fit it on the opposite side.Pull hinge pintogether with disc
and adjustable footupwards and
off.
Remove cover cap.
Undo screwsand take hinge plate
off.
Undo the screw of hinge part	on
hinge plateslightly. Fit it into the
hole opposite in hinge plateand
tighten up the screw.
Refit cover capin the other hole.

Remove coverand fit it into the
holes on the opposite side.
Changing the door hinging
41 
						

							Screw hinge plateinto position on
the opposite side using the twoouter
long slots only. To make it possible to
align the door later, do not replace
thecentrescrew at this stage.
Important. Screw the adjustable foot
into hinge pinas far as it will go.
Refit hinge pintogether with disc
and adjustable foot. Important.
The notch at the bottom of the hinge
pin should face towards the back.
Place the door onto hinge pin.

Close the appliance door.Fit hinge plateonto the opposite
side and secure it with screws.
Fit coversandto their opposite
sides.
Align the door with the appliance
housing using the long slots in the
lower hinge plate. Then tighten the
screws.
Changing the door hinging
42 
						

							Refitting the handle
Please make sure you follow the
instructions below carefully when
you refit the handle. The door seal
will be damaged if the handle is
fitted incorrectly.
Loosely attach the handle to the
opposite side of the door with the two
front screws.
Mounting platemust be positioned
on the side of the door so that when the
door isclosedit is flush with the side of
the appliance.
If this is not the case,

tighten both grub screwswith a
suitable allen key until mounting plate
lines up correctly.

Then tighten all 4 screws.

Slide the side section of the handle
into the guides on the mounting
plate until it clicks into place.
It is important to check that the side
section of the handledoes not
come into contact with the door seal
when opening the door, as this
would damage the door seal
permanently.
If, after you have refitted the handle,
you find that the side section does
touch the door seal when the door is
opened:
Realign mounting platewith grub
screwsuntil the mounting plate
and the side section of the handle
are at the correct angle and the side
section does not touch the door seal
when the door is opened.
Changing the door hinging
43 
						

							The appliance door can be aligned to
the housing using the outer long slots in
the lower hinge plate.
In the following illustration the door
is not shown in the closed position to
make it easier to see what you have
to do.
Remove centre screwfrom the
hinge plate.
Slightly loosen both outer screws.
Align the door by sliding the hinge
plate to the left or right.

Then tighten screwsagain. Screw
does not need to be used again.
Aligning the appliance door
44 
						

							Top box
Appliance
Housing unit
Wall
The appliance can be installed in a
kitchen run. To match the height of the
rest of the kitchen, the appliance can
be fitted with a suitable top box.
A ventilation gap of at least 50 mm
depth must be allowed for behind the
appliance across the entire width of the
top box for air to circulate.
The cross section of the air outlet under
the room ceiling must be at least
300 cm
2to ensure that air can circulate
without hindrance. Otherwise the
appliance has to work harder, resulting
in an increase in electricity
consumption.
The air inlet and outlet must not be
covered or blocked in any way.
They should be dusted on a regular
basis.
When built into a kitchen run (max.
depth 580 mm) the appliance can be
installed directly next to a kitchen
furniture housing unit. The appliance
door will protrude in front of furniture
fronts at the sides by 34 mm and by
55 mm in the middle of the door. This
enables the doors to be opened and
shut without being obstructed.
When installednext to a walla
distance of approx. 55 mm must be
maintained on the hinge side between
the walland the appliance,so
that the doors and the handles have
sufficient space for opening.
Building in the appliance
45 
						

							46 
						

							47 
						

							Alteration rights reserved / 4912
K 11820 SD, K 12820 SD, K 12820 SD edt/csM.-Nr. 09 434 270 / 00