Miele G 848 Manual

^Pull out the non-return valve.
^Rinse the non-return valve under run-
ning water.The drain pump is situated under the
non-return valve (see arrow).
^Before returning the non-return valve,
check to make sure that the drain
pump is not obstructed. Spin the pro-
peller several times in both direc-
tions; it should turn smoothly.
^Carefully refit the non-return valve
and secure it with the locking clamp.
^Refit and secure the combination
filter.
Solving problems
51 

After sales service
If you are unable to resolve a problem
or if the appliance is under warranty,
please contact your Miele Dealer or the
Miele Technical Service Department.
(See back cover for telephone num
-
bers).
Please have the model and serial num
-
ber of the appliance available. These
can be found on the data plate on the
upper inside edge of the dishwasher
door.Program update function - PC
The “PC” indicator has the function of
Program Correction (PC). This allows a
technician to update the...

Special accessories
To make the most of your dishwasher
If you would like... then you need...
...to wash bottles,
e. g. milk or baby bottles... a bottle holder
... to wash long stemmed glassware ... a glassware insert for the upper
basket
Special accessories
53 

Transport
To transport the dishwasher, e.g. when
moving to a new home, note the follow
-
ing:
–Empty the dishwasher,
–Secure any loose parts, e. g. hoses,
cables, cutlery baskets.
–Transport the dishwasher in the up
-
right position.
If unavoidable it may be transported
on its back.
Do not transport it on its side or on
the door because residual water in
the machine will leak. This residual
water could get into the electronic
unit and cause damage.
Transport
54 

Technical data
Series designation HG01
Height 33 1/16 (84 cm) [adj. + 2/5.0 cm]
Width 23 9/16 (59.8 cm)
Width of cabinet opening 23 5/8 (60 cm)
Depth 22 7/16 (57 cm)
Depth with door open 47 7/16 (120.5 cm)
Weight approx. 119 lbs/55 kg
Voltage 110/120 V AC
Rated load 12.5 A / 1500 W
Fuse rating 15 A
Water pressure 15 – 150 psi (1.0 - 10 bar)
Water connection max. 140 °F (60 °C)
Drain height max. 39 (1 m)
Drainage length max. 13 ft (4 m)
Connection cable approx. 4 ft (1.2 m)
Capacity 14 place settings...

Program chart
Program When to use Detergent
chlorine
free1)containing
chlorine2)
Compart
-
ment
II
(Wash
cycle)Compart
-
ment
I
(Pre-
wash)Compart
-
ment
II
(Wash
cycle)
Normal
3)
55 °C/130 °Ffornormaleveryday loads 100 % 20 % 80 %
Sani Wash as Normal 55 °C/130 °F,
but with longer wash time forheavily soiled
loads, also suitable for chlorine free deter
-
gents100 % 20 % 80 %
Normal
65 °C/150 °Fas Normal 55 °C/130 °F,
but at a higher temperature forstubborn
dried on food100% 20 % 80 %
Light Wash
55 °C/130...

Program Cycle Usage Duration
Electric (kWh) Water Minutes
(approx.)
1.
Pre-
liminary
pre-
wash2.
Pre-
washMain
washInterim
rinseFinal
rinseDrying Cold
water
con
-
nection
(10 °C/
50 °F)Hot
water
con
-
nection
(49 °C/
120 °F)Liters/
GallonsCold
water
con
-
nection
(10 °C/
50 °F)Hot
water
con
-
nection
(49 °C/
120 °F)
XXX
55 °C/
130 °FXX
65 °C/
150 °FX 1.62 0.8 24 / 6.3 150 114
XX
65 °C/
150 °FXX
75 °C/
170 °FX 2.40 1.5 19 / 5 185 145
XXX
65 °C/
150 °FXX
65 °C/
150 °FX 1.82 1.1 24 / 6.3 156 110
X
55 °C/...

58 

59 

Alteration rights reserved/ (G848/G849) / 002 1700
These instructions are printed on 100% recycled paper and are completely Biodegradable.