Miele G 2830 Sci Operating Instructions

Keypad tone
A tone will sound when a control is
touched.
The keypad tone is turned on by
default.
^Select the desired option and confirm
with
OK.
Brightness
The display brightness can be adjusted
in 17 levels.
The brightness is set to level 8 by
default.
^Select the desired brightness and
confirm with
OK.
Contrast
The display contrast can be adjusted in
17 levels.
The contrast is set to level 8 by default.
^
Select the desired contrast and
confirm with
OK.
Standby
To save energy the display is turned...

Dealer
Demo modes are only for
showrooms.
The dishwasher has three demo
programs for showrooms.
The programs Demo mode and
Endless demo mode show the use
and function range of the dishwasher.
–
Demo mode:
The program is started by touching a
control. It runs once and must be
started again.
–
Endless demo mode:
The program starts after it was
activated and runs in a loop until it is
turned off.
–
Demo wash sound:
The program activates the pumps to
demonstrate the wash sound.
Turning the demo mode on
^...

With the aid of the following guide, minor problems can be fixed without a service call.
,Repairs should only be carried out by a qualified and trained person in
accordance with local and national safety regulations. Unauthorized repairs
could cause personal injury or machine damage.
Technical faults
Issue Possible fault Solution
After the dishwasher
was turned on the
display stays off and the
stand by indicator does
not flash.The machine is not
plugged in.Insert the plug.
The fuse has tripped. Reset the...

Problems water intake/drain
Issue Possible fault Solution
The buzzer sounds.
The display shows the
following:
No water intake
Open the water faucetThe water supply is
closed.Open the water supply all the
way.
Fault water intake FXXBefore fixing the fault:
–Turn the dishwasher off by
touching thescontrol.
Fault F12/F13: Fault in
the water intake.–Open the water supply all
the way and restart the
program.
–Clean the water intake filter,
see User Maintenance
Instructions.
–The water pressure at the
water...

Issue Possible fault Solution
The program "Energy
Saver" displays the
fault:
Water intake temp. too
low
The intake water does not
have a minimum
temperature of 115°F
(45°C). See Plumbing -
Connection to the water
supply.–Restart the program.
–If the fault is displayed
again, use a different
program.
The buzzer sounds.
The display shows
the following:
Drain fault FXX
Before fixing the fault:
–Turn the dishwasher offs.
Fault F11: Fault in the
water drain. There might
be water in the wash...

General problems with the dishwasher
Issue Possible fault Solution
The display remains
off.The display has gone
into Standby mode to
save energy.Touch any control.
See SettingsJ- Standby for
more info.
The buzzer sounds
during a running
program. The display
shows the following:
Salt container lid
Close the salt container lid
The salt container lid
was not closed
properly.–Close the salt container lid
If the salt container lid
opened during a running
program, also:
–Turn the dishwasher off
and on again...

Issue Possible fault Solution
Detergent is left in the
dispenser at the end of a
program.The dispenser was damp
when detergent was
added.Dry the dispenser before
adding detergent.
The detergent lid cannot
be closed properly.Detergent residue is
blocking the catch.Remove the residue.
The door and the
interior walls are still
wet after a program has
finished.This is not a fault. It is the
normal operating mode of
the drying system.The moisture will
evaporate after a short
time.
Water remains in the
wash...

Sounds
Issue Possible fault Solution
There is a knocking
noise in the wash
cabinet.The spray arm is hitting an
item in the basket.Interrupt the program,
rearrange the items
blocking the spray arm.
There is a rattling
noise in the wash
cabinet.Items are not secure in the
wash cabinet.Interrupt the program and
rearrange loose items.
There is a knocking
noise in the water
pipes.This may be caused by
the installation or the
diameter of the pipe.This has no effect on the
dishwasher. If in doubt
contact a...

Poor cleaning results
Issue Possible fault Solution
The dishes are not
clean.The dishes were not loaded
correctly.See Loading the
dishwasher.
The program was not
powerful enough.Select a more intensive
program, see Program
Guide.
Stubborn but normal soiling
(e.g. tea).Use the function Adjust
Sensor Wash.
See SettingsJ- Adjust
Sensor Wash.
Not enough detergent was
dispensed.Use more detergent, see
Adding detergent.
The spray arms are blocked
by items.Turn the spray arm and
rearrange the dishes if...

Issue Possible fault Solution
Dishes are not dry,
glasses and
cutlery are
spotted?The rinse aid setting may
be too low or the rinse aid
reservoir is empty.Increase the dosage, refill the
reservoir or switch the rinse
aid product when refilling, see
Before using for the first
time.
Dishes were taken out too
soon.Leave dishes in longer, see
Use.
2 in 1 or 3 in 1 products
were used. These products
have a low drying effect.Set the detergent type to
Powder and insert rinse aid.
See SettingsJ- Detergent.
The...