Miele G 1232 Sci Operating Instructions

Switching on
^Make sure the spray arms are not
obstructed.
^Close the door.
^Open the stopcock, if it is closed.
^Switch the dishwasher on with the
On/Off buttons.
The Start/Stop indicator light flashes
and the indicator light comes on next to
the last programme selected.
Selecting a programme
Choose your programme according to
the type of load and how dirty it is.
The different programmes and their
uses are described in the programme
chart later on in this booklet.
Starting a programme
^Select the...

Display
The duration of the programme
selected appears in hours and minutes
in the display before the programme
begins. During the programme, the
time left until the end of the programme
is displayed.
The time displayed may vary with the
same programme. This is partly
because of the water inlet temperature
at each intake, and partly because of
the amount and soiling level of the
crockery.
When a programme is selected for the
first time, the display shows an average
time for a cold water intake.
The times...

Unloading the dishwasher
Dishes tend to break and chip more
easily when they are hot.
Allow the dishes to cool until they are
comfortable enough to handle before
unloading them.
If you open the door fully after switching
off, the dishes will cool much faster.
^First unload the lower basket, then
the upper basket and cutlery tray
(depending on model).
This will prevent water drops from the
upper basket and cutlery tray from
falling onto the dishes in the lower
basket.
Interrupting a programme
A programme...

Additional functions
Tab function
You can programme your dishwasher to
ensure excellent results when using
tablet detergents by simply selecting
the 2 in 1 or 3 in 1 function using the
Tab button.
The programme sequence will be
adjusted to the type of detergent
selected. Depending on the
programme, the duration can be
considerably longer.
"2 in 1":
When the 2 in 1 function is selected,
the programme sequence is adjusted
for 2 in 1 tabs (detergent containing
rinse aid).
The dispensing of rinse aid...

Delay start
The start time of a programme can be
delayed, e.g. to benefit from economy
rates of electricity. A delay start time of
between 30 minutes and 24 hours can
be selected.
With a delay start time of between
30 minutes and 9 hours 30 minutes, the
time is set in 30 minute stages. For
10 hours or more it is set in one hour
stages.
When using the Delay start function,
make sure that the compartment is
dry before adding detergent. Wipe
dry with a cloth if necessary. If the
compartment is wet, powder...

The time starts counting down until the
programme start time: in 1 hour steps
for delay start periods of over 10 hours,
and in minutes for delay start periods of
under 10 hours.
At the end of the delay period, the
programme selected begins
automatically. The time left for a
programme to run then shows in the
display, the Delay start indicator light
goes out and the Start/Stop indicator
light comes on.
How the Delay start time is shown in
the display:
up to 59 minutes:
e.g. 30 minutes =30
between 1 hour...

Factory default setting
If you have altered any settings from
the factory default, you can re-set them
back to the factory default settings as
follows:
^Switch the dishwasher off with the
On/Off buttons.
^Press the Start/Stop button in and
whilst holding it inswitch the
dishwasher on using the On/Off
buttons.
Keep the Start/Stop button pressed in
for at least four seconds until the
Start/Stop indicator light comes on.
If this does not happen, start the
procedure from the beginning again.
^Press the Delay...

Adjust sensor wash
You can adjust the sensor wash
programme so that it will remove
stubborn soiling in a lightly soiled load.
^Switch the dishwasher off with the
On/Off buttons.
^Press the Start/Stop button in and
whilst holding it inswitch the
dishwasher on using the On/Off
buttons.
Keep the Start/Stop button pressed in
for at least four seconds until the
Start/Stop indicator light comes on.
If this does not happen, start the
procedure from the beginning again.
^Press the Delay start button five
times....

Check your dishwasher regularly
(approx. every 4 - 6 months). This
way faults and problems can be
avoided.
Cleaning the wash cabinet
The wash cabinet is largely
self-cleaning, provided that the correct
amount of detergent is always used.
If, however, there are limescale or
grease deposits in the cabinet these
can be removed with a proprietary
dishwasher cleaner, such as the Miele
dishwasher cleaner (available from the
Miele UK Spare Parts Department).
Cleaning the door and the door
seal
^Wipe the door...

Cleaning the control panel
,Do not use abrasive cleaning
agents, glass cleaning agents or
all-purpose cleaners. Because of
their chemical composition they
could cause serious damage to
surfaces.
Plastic panels:
^This type of control panel should only
be wiped with a damp cloth or
suitable cleaning agent designed for
use on plastic.
Stainless steel panels:
^Control panels made of stainless
steel should be cleaned using a
damp cloth and a little washing up
liquid, or a proprietary non-abrasive
cleaning...