Miele G 1202 Sci Operating Instructions

							Check your dishwasher regularly
(approx. every4-6months). This
way faults and problems can be
avoided.
Miele branded cleaning and
conditioning products are available
from the Miele Spare Parts
Department or via the Internet at
www.miele-shop.com.
,The external surfaces of the
dishwasher are susceptible to
scratching.
Contact with unsuitable cleaning
agents can alter or discolour the
outer surfaces.
Cleaning the wash cabinet
The wash cabinet is largely
self-cleaning, provided that the correct
amount of detergent is always used.
If, however, there are limescale or
grease deposits in the cabinet, these
can be removed with a proprietary
dishwasher cleaner or conditioner.
Cleaning the door and the door
seal
^
Wipe the door seals regularly with a
damp cloth to remove food deposits.^When the dishwasher is being loaded,
food and drink residues may drip onto
the sides of the dishwasher door.
These surfaces are outside the wash
cabinet and are not accessed by
water from the spray arms. Any
soiling should be wiped off these
surfaces before the door is closed.
Cleaning the door front
,Remove any soiling immediately.
If not, it might become impossible to
remove and could cause the outer
surface to alter or discolour.
^Clean the front using a damp Miele
microfibre E-cloth or with a sponge and
a solution of hot water and washing-up
liquid. Then dry with a soft cloth.
To avoid damaging the external
surfaces, do not use:
– cleaning agents containing soda,
ammonia, acids or chlorides,
–
cleaning agents containing
descaling agents,
–
abrasive cleaning agents, e.g.
powder cleaners and cream cleaners.
–
solvent-based cleaning agents,
–
stainless steel cleaning agents,
–
dishwasher cleaner,
–
oven sprays,
–
glass cleaning agents,
–
hard, abrasive sponges and
brushes, e.g. pot scourers,
–
sharp metal scrapers.
Cleaning and care
41
 
						

							Cleaning the filters in the wash
cabinet
The filter combination in the base of the
wash cabinet retains coarse soil from
the suds solution, preventing it
accessing the circulation system and
re-entering the cabinet through the
spray arms.
,The dishwasher must not be
used without all the filters in place.
Collection of coarse soil may cause the
filters to clog. The level of soiling and
time it takes before the filters need
cleaning will vary depending on use.
Check the condition of the filters
regularly and clean them if necessary.
^Switch the dishwasher off.^Turn the handle anti-clockwise to
release the filter combinationa.
^Lift the filter combination out of the
dishwasherb. Remove any coarse
particles and rinse the filter well
under running water. Use a nylon
brush if necessary.
Cleaning and care
42
 
						

							To clean the inside of the filter, the flap
must be opened:
^Press catchesatogether in the
direction of the arrows as shown,
and open the filterb.
^Rinse all the filters under running
water.
^Then close the flap so that the catch
engages.^Replace the filter combination so that
it lies flat in the base of the wash
cabinet.
^Then turn the handle clockwise, until
the arrows line up, to lock the filter
combination in place.
,Take care when you are fitting
the filter combination that it is
secured in position correctly.
Otherwise coarse soil could get into
the circulation system and cause a
blockage.
Cleaning and care
43
 
						

							Cleaning the spray arms
Particles of food can get stuck in the
spray arm jets and bearings. The spray
arms should therefore be inspected
and cleaned regularly (approx. every
4 - 6 months).
^Switch the dishwasher off.
Remove the spray arms as follows:
^Take out the cutlery tray (if your
dishwasher is fitted with one).
^Push thetopspray arm upwards to
engage the inner ratchet. Then
unscrew the spray arm.
^
Push themiddlespray arms upwards
ato engage the ratchet. Then
unscrew the spray armb.^Remove the lower basket.
^Pull thelowerspray arm firmly
upwards to remove it.
^
Use a pointed object to push food
particles into the spray arm jets.
^
Rinse thoroughly under running
water.
^
Replace the spray arms and check
that they rotate freely.
Cleaning and care
44
 
						

							With the aid of the following guide, faults in the performance of the appliance,
some of which may result from incorrect operation can be put right without
contacting the Miele Service Department.
,Repairs should only be carried out by a suitably qualified and trained
person in strict accordance with current local and national safety regulations.
Unauthorised or incorrect repairs could cause personal injury or damage to the
appliance.
Technical problems
Problem Possible cause Remedy
The Start/Stop indicator
does not flash after the
dishwasher has been
switched on using the
On/Off buttonK.The appliance is not
plugged in.Insert the plug and switch
on at the socket.
The fuse has tripped. Reset or replace the fuse.
(Minimum fuse rating -
see data plate).
The dishwasher stops
during a programme.The fuse has tripped. Reset or replace the fuse.
(Minimum fuse rating -
see data plate).
Problem solving guide
45
 
						

							Problem Possible cause Remedy
The Wash/Rinse,
Drying and End
indicator lights flash
simultaneously.
Fault code FXX shows
in the display.There may be a
technical fault.–Clean the water inlet filter
and clean the drain pump
and non-return flap as
described in Maintenance.
If this does not resolve the
problem:
–switch the dishwasher off
with the On/Off buttonK.
After a few seconds:
–Switch the dishwasher back
on.
–Select the programme
required with the
programme selector button.
– Press the Start/Stop button.
If the programme sequence
indicator lights flash again,
there is a technical fault.
– Call the Service
Department.
The drain pump works
even when the door is
open.Fault F70:
The Waterproof System
has reacted.– Close the stopcock.
– Call the Service
Department.
Problem solving guide
46
 
						

							The dishwasher does not fill/drain.
Problem Possible cause Remedy
The Inlet/Drain
check indicator
flashes.The stopcock is
closed.Open the stopcock fully.
The dishwasher
stops during a
programme.
The Inlet/Drain
check indicator
flashes.
Fault code FXX
shows in the
display.Before rectifying the problem
you must:
–Switch the dishwasher off with
the On/Off buttonK.
Fault F12/F13:
Water inlet restricted.–Open the stopcock fully.
–Clean the water inlet filter (see
Maintenance).
– The water pressure at the
intake is lower than 30 kPa
(0.3 bar).
Seek professional advice.
Fault F11:
Water outlet is
restricted, water
remains in the wash
cabinet at the end of a
programme.– Clean the filter combination.
See Cleaning and care.
– Clean the drain pump. See
Maintenance.
– Clean the non-return valve.
See Maintenance.
–
Remove any kink in the drain
hose.
Problem solving guide
47
 
						

							General problems
Problem Possible cause Remedy
The display is dark.The time display switches
off automatically in
Standby Mode to save
energy.Press any button to come
out of Standby mode.
Detergent residue is left
in the dispenser at the
end of a programme.The dispenser was still
damp when detergent was
added.Make sure the dispenser
is dry before adding
detergent.
The detergent
dispenser lid cannot be
closed properly.Clogged detergent
residue is blocking the
catch.Clean the detergent from
the catch.
At the end of a
programme there is a
film of moisture on the
inside of the door and
the interior walls.This is caused by the
drying system and does
not indicate a fault.The moisture will dissipate
after a short while.
Water remains in the
wash cabinet at the end
of a programme.Before rectifying the
problem you must:
– Switch the dishwasher
off with the On/Off
buttonK.
The filter combination in
the wash cabinet is
clogged.Clean the filter
combination. See
Cleaning and care.
The drain pump or
non-return valve may be
blocked.Clean the drain pump or
the non-return valve. See
Maintenance.
The drain hose is kinked. Remove any kink from the
drain hose.
Problem solving guide
48
 
						

							Noises
Problem Possible cause Remedy
Knocking noise in the
wash cabinet.A spray arm is knocking
against an item in a
basket.Interrupt the programme,
and rearrange the items
which are obstructing the
spray arm.
Rattling noise in the
wash cabinet.Items of crockery are
insecure in the wash
cabinet.Interrupt the programme,
and rearrange the items of
crockery.
Knocking noise in the
water pipes.This may be caused by
the on-site installation or
the cross-section of the
piping.This has no influence on
dishwasher function. If in
doubt, contact a suitably
qualified plumber.
Problem solving guide
49
 
						

							Unsatisfactory washing result
Problem Possible cause Remedy
The dishes are not
clean.The dishes were not loaded
correctly.See notes in Loading the
dishwasher
The programme was not
powerful enough.Select a more intensive
programme. See
Programme chart.
There is some stubborn
soiling although most of the
crockery is only lightly soiled
(e.g. with tea stains).Use the Adjust Sensor
wash function (see
Additional functions).
Not enough detergent was
dispensed.Use more detergent, or
change your detergent.
Items are blocking the path
of the spray arms.Rearrange the items so that
the spray arms can rotate
freely.
The filter combination in the
base of the wash cabinet is
not clean or is not correctly
fitted. This may cause the
spray arm jets to get
blocked.Clean and/or fit the filter
combination correctly. Clean
the spray arm jets. See
Cleaning and care.
The non-return valve is open
and blocked. Dirty water has
flowed back into the wash
cabinet.Clean the drain pump and
the non-return valve. See
Maintenance - Cleaning the
drain pump and non-return
valve.
Smearing appears
on glassware and
cutlery, there is a
bluish sheen on
the surface of
glassware; film can
be wiped off.The rinse aid dosage is set
too high.Reduce the dosage. See
Before using for the first
time - Rinse aid.
Problem solving guide
50