Miele G 1143 Sc Operating Instructions

							Problem Possible cause Remedy
Glassware has a
brown or blue tinge,
and film cannot be
wiped off.This may be caused by the
detergent.Change your detergent.
Glassware is dull and
discoloured; film
cannot be wiped off.The glassware is not
dishwasher-proof. The
surfaces are affected.There is no remedy.
Purchase glassware which
is dishwasher-proof.
Tea or lipstick stains
have not been
completely removed.The wash temperature of
the selected programme
was too low.Select a programme with a
higher wash temperature.
The bleaching effect of the
detergent used is too low.Change your detergent.
Plastic items are
discoloured.Natural dyes e.g. from
carrots, tomatoes or
ketchup may be the cause.
The amount of detergent
used or its bleaching effect
was not sufficient to deal
with natural dyes.Use more detergent. See
Operation.
Discolouration is irrevers
-ible.
There are rust stains
on cutlery.The affected items are not
corrosion resistant.There is no remedy.
Purchase cutlery which is
dishwasher-proof.
The Quick wash
programme was not run
after dishwasher salt was
added. Traces of salt have
got into the wash cycle.Always run the Quick
wash programme, without
any crockery in the
dishwasher, after adding
dishwasher salt.
The salt reservoir cap has
not been screwed on
correctly.Replace it, making sure
that it screws back on
correctly.
Problem solving guide
51
 
						

							Cleaning the water inlet filter
A filter is incorporated in the screw
connection of the valve on the water
inlet hose. The filter must be cleaned
when dirty, otherwise insufficient water
flows into the wash cabinet.
,The plastic housing of the water
connection contains an electrical
component. It must not be dipped in
water.
Recommendation
If the mains water contains a large
number of insoluble substances, we
recommend fitting a large-area filter in
the connection between the stopcock
and the water inlet hose threaded
union. This filter is available from the
Miele Spares Parts dept.
Cleaning the filter:
^Disconnect the dishwasher from the
mains supply. Switch off at the mains
socket and withdraw the plug.
^
Turn off the stopcock.
^
Unscrew the inlet hose.^Carefully remove the seal.
^Withdraw the filter using pointed
pliers and rinse clean under running
water.
^Replace the filter and seal, making
sure they are sitting correctly.
^Reconnect the inlet hose to the
stopcock, making sure it goes on
correctly and is not cross-threaded.
^
Turn on the stopcock gradually to test
for leaks. If there is a leak, the inlet
hose might not be on securely, or it
may have been screwed on at an
angle. Unscrew and reconnect the
water inlet valve correctly.
Problem solving
52
 
						

							Cleaning the drain pump and
non-return valve
If the water has not been pumped away
at the end of a programme the drain
pump or the non-return valve might be
blocked. They are, however, easy to
clean. Watch out for glass or bone
splinters which could cause injury.
^Disconnect the dishwasher from the
mains supply. Switch off at the mains
socket and withdraw the plug.
^Take the filter combination out of the
wash cabinet (see Cleaning and
care, Cleaning the filters in the wash
cabinet).
^Scoop the water out of the cabinet
using a suitable container or utensil.
^
Press the catch for the non-return
valve inwardsa.
^
Lift out the non-return valveband
rinse well under running water.
^
Remove all foreign objects from the
non-return valve.The drain pump is situated under the
non-return valve (see arrow).
^Remove all foreign objects from the
drain pump (watch out for glass or
bone splinters which are particularly
difficult to detect and could cause
injury). Turn the drain pump impeller
by hand to check that there are no
more obstructions. You will feel a little
resistance when you turn the impeller.
^
Carefully replace the non-return
valve, and secure it with the catch.
,Ensure that the catch engages.
Problem solving
53
 
						

							Repairs
In the event of any faults that you
cannot remedy yourself, please
contact:
–your Miele dealer, or
–the Miele Service Department
(see back cover for contact details).
^When contacting your Dealer or the
Miele Service Department, please
quote the model type and number of
your appliance, both of which are
shown on the data plate on the right
hand side of the door.
Please note that telephone calls may
be monitored and recorded for
training purposes.Future updates (PC)
The programme update function (PC) is
designed to enable a service
technician to update your appliance’s
electronics in keeping with advances in
technology.
The PC indicator light is used as the
interface for this programming.
For testing institutes
The"Comparison tests"document
gives information regarding loads and
programmes used for comparison
testing.
This document can be ordered by
e-mail from:
– testinfo|miele.de
^Please give your postal address, as
well as the model type and number of
your dishwasher (see data plate).
After sales service
54
 
						

							To make the most of your dishwasher
Optional accessories for particular purposes are available from your Miele dealer
or from the Spare Parts Department (some may be supplied as standard
depending on model).
If you would like to … you will need to order …
… wash long-stemmed glassware … a glassware insert for the upper
basket
... wash a Miele Cappuccinatore … a Cappuccinatore insert for the
upper basket
... wash bottles,
e. g. milk or baby bottles… a bottle holder
… wash additional items of cutlery … a small cutlery basket for the lower
basket
... wash a lot of glasses … a glassware insert for the bottom
basket
... wash large plates ... an insert for plates up to:
-  33 cm diameter
-  35 cm diameter
Optional accessories
55
 
						

							Programme When to use
Sensor wash Sensor controlled programme
fornormally soiledcrockery
Quick wash 40 °C Quick programme forlightly soiledcrockery, e.g. party crockery;
for flushing out salt residues after replenishing the salt reservoir;
includes sensor controlled
3)glass care;
not suitable for tablet detergents.
Sensor wash
gentle:Sensor controlled
3)gentle programme
forlightly soiled and temperature sensitivecrockery and glassware;
reduce detergent by 50%
Energy save
1)fornormaleveryday loads,
energy saving programme which uses a low temperature and long programme
duration;
includes sensor controlled
3)glass care
Pots & pans 75 °C fornormally soiled pots, pans, dishes etcwithdried onsoiling;
for very heavy soiling, add 20% more detergent than recommended
Pre-wash for rinsing crockery to avoid smells, if a complete cycle is not yet needed
1) Standard programme for energy labelling.
2) See Operation, Display.
3) Depending on model.
Programme chart
56
 
						

							Programme sequence Consumption Duration
Energy   kWh Water h:min2)
Pre-
wash
12Main
washInterim
rinse
12Final
rinseDrying Cold
water
connec-
tion
(15 °C)Hot water
connec-
tion
(55 °C)Litres Cold
water
connec-
tion
(15 °C)Hot water
connec-
tion
(55 °C)
if
requiredX
45 °- 65 °if
requiredX
65 °X 1.0-1.5 0.65-0.8 13-22 1:39-2:34 1:24-2:08
X
40 °XX
50 °0.75 0.22 13 0:33 0:22
if
requiredX
37 °- 48 °if
requiredX
55 °X 0.85-1.0 0.4-0.5 13-22 1:25-1:55 1:14-1:36
X
45 °XX
60 °X 1.05 0.7 13 2:56 2:44
XX
75 °XX
65 °X 1.6 1.0 17 2:46 2:30
X 0.02 0.02 5 0:12 0:12
On G 2XXX models (see data plate), the max. energy consumption is 0.1 kWh and the water
consumption is up to 1 litre higher, except on the Pre-wash programme.
The durations given can vary depending on individual circumstances.
Values quoted are in accordance with EN 50242. Results may differ, depending on individual
conditions and the level of soiling.
Programme chart
57
 
						

							Electrical connection U.K.
,All electrical work must be
carried out by a suitably qualified
and competent person, in
accordance with current local and
national safety regulations (BS 7671
in the UK).
Ensure power is not supplied to the
appliance until after installation work
has been carried out.
The appliance is supplied with a mains
cable with moulded plug ready for
connection to a 230-240V mains
supply. Please ensure the connection
data quoted on the data plate match
the household mains supply.
Connection should be made via a
suitable switched socket which is easily
accessible after installation.
For extra safety it is advisable to install
a residual current device (RCD), with a
trip current of 30 mA (in accordance
with DIN VDE 0664, VDE 0100 Section
739).
Do not connect via an extension lead.
Extension leads do not guarantee the
required safety of the appliance (e.g.
danger of overheating).Non-rewireable plugs BS 1363
The fuse cover must be refitted when
changing the fuse, and if the fuse cover
is lost, the plug must not be used until a
suitable replacement is obtained. The
colour of the correct replacement cover
is that of the coloured insert in the base
of the plug, or the colour that is
embossed in words on the base of the
plug (as applicable to the design of
plug fitted).
Replacement fuses should be ASTA
approved to BS 1362 and have the
correct rating. Replacement fuses and
fuse covers may be purchased from
your local electrical supplier.
WARNING: THIS APPLIANCE
MUST BE EARTHED
Electrical connection
58
 
						

							Connection to the water supply
,Water in the dishwasher must
not be used as drinking water.
–The dishwasher may be connected
to a cold or hot water supply, max.
60 °C. We would only recommend
connection to a hot water supply if it
is economical, e.g. a solar powered
supply. When connected to a hot
water supply all programme stages
which would otherwise be carried out
with cold water will be carried out
with hot water.
– The inlet hose is approx. 1.5 m long.
A 1.5 metre long flexible metal
extension hose, pressure tested to
14000 kPa/ 140 bar, is available as
an optional accessory if required.
– A stopcock with a 3/4  male thread
must be provided on site.
– This appliance is constructed to
comply with IEC/EN/DIN 61770 //
VDE 0700 Section 600, and may be
connected to a suitable supply
without an extra non-return valve if
national regulations permit.
–
The water pressure (flow pressure at
the take-off point) must be between
30 and 1000 kPa (0.3 and 10 bar).
If the water pressure is too high, a
pressure reducing valve must be
fitted.
!The inlet hose mustnotbe
shortened or damaged in any way
as it contains electrical components
(see illustration).
Plumbing
59
 
						

							Drainage
–The appliance drainage system is
fitted with a non-return valve, which
prevents dirty water from flowing
back into the dishwasher via the
drain hose.
–The dishwasher is supplied with
approx. 1.5 m of flexible drain hose
with an internal diameter of 22 mm.
–The drain hose can be extended
using a connection piece to attach a
further length of hose.
The drainage length must not be
longer than 4 m, and the delivery
head must not exceed 1 m.
– If the hose is to be directly fitted to
the drainage outlet on site, use the
hose clip supplied.
– The hose can be directed to the left
or the right of the appliance.
– The on-site connector for the drain
hose can be adapted to different
widths of hose. If the connector
protrudes too far into the drain hose,
it will need to be shortened.
Otherwise the drain hose may
become blocked.
–
The drain hose must not be
shortened.
–
Make sure that there are no kinks in
the hose, and that it is not squashed
or stretched.Venting the drainage system
If the on-site drain connection is
situated lower than the guide path for
the bottom basket rollers in the open
door the drainage system must be
vented. Otherwise a siphoning effect
during a programme can cause the
appliance to empty itself of water.
To vent it:
^Open the dishwasher door fully.
^Pull the lower spray arm firmly
upwards to remove it.
^
Cut off the top of the vent valve in the
wash cabinet.
Plumbing
60