Miele Fn 9752 I Operating And Installation Instructions

							In the event of a fault which you cannot
correct yourself, or if the appliance is
under guarantee, please contact:
–your Miele Dealer
or
–Miele
(see back cover for contact details).
When contacting your Dealer or Miele,
please quote the model and serial
number of your appliance. This
information is given on the data plate
inside your appliance.
Please note that telephone calls may
be monitored and recorded for
training purposes.
N.B. A call-out charge will be applied
for service visits where the problem
could have been resolved as described
in these instructions.
Guarantee
For information on the appliance
guarantee specific to your country
please contact Miele. See back cover
for contact details.
In the U.K. your appliance is
guaranteed for 2 years from the date of
delivery. However, you must activate
your cover by calling 0845 365 6640 or
registering online at www.miele.co.uk.
After Sales / Guarantee
31
 
						

							Electrical connection U.K.
All electrical work should be carried out
by a suitably qualified and competent
person in strict accordance with current
local and national safety (BS 7671 in
the UK).
The appliance is supplied with a mains
cable and moulded plug ready for
connection to an a.c. single phase
220-240 V 50 Hz supply.
The voltage and frequency are given on
the data plate. Please ensure that these
match the household mains supply. The
fuse rating is quoted on the plug.
Connection should be made via a
suitable switched socket which is easily
accessible. For extra safety it is
advisable to protect the appliance with
a suitable residual current device
(RCD).
Do not connect the appliance to the
mains electricity supply by an extension
lead. Extension leads do not guarantee
the required safety of the appliance
(e.g. danger of overheating).
This appliance must not be connected
to the inverter of an autonomous power
supply, e.g. a solar power system.
When switching the appliance on, a
surge in power could trigger the safety
cut-out mechanism. This could damage
the electronic unit.
The appliance must not be used with
so-called energy saving devices. These
reduce the energy supply to the
appliance which could then become
too warm. Using such devices could
alter the specification of the product.Non-rewireable plugs (BS 1363)
The fuse cover must be re-fitted when
changing the fuse, and if the fuse cover
is lost, the plug must not be used until a
suitable replacement is obtained. The
colour of the correct replacement cover
is that of the coloured insert in the base
of the plug, or the colour that is
embossed in words in the base of the
plug (as applicable to the design of the
plug fitted).
Replacement fuses should be ASTA
approved to BS 1362 and have the
correct rating. Replacement fuses and
fuse covers may be purchased from
your local electrical supplier.
WARNING
THIS APPLIANCE MUST BE
EARTHED
Electrical connection
32
 
						

							This appliance must be built in,
otherwise it could tip up.
Location
This appliance should be installed in a
dry, well-ventilated room. It should not
be installed where it is exposed to
direct sunlight or directly adjacent to a
heat-producing appliance such as an
oven or a radiator. The room
temperature should not go above or
below the climate range for which the
appliance is designed. The higher the
ambient temperature of the room, the
more energy the appliance requires to
operate.
Important: tropical / humid
environments
During periods of high humidity,
some condensation may appear on
outside surfaces of cooling
appliances. This condensation will
disappear when humidity levels
drop. For prevention, it is advisable
to install the appliance with sufficient
ventilation in a dry and/or an
air-conditioned room.
Please ensure that doors are closing
and sealing properly.
Please ensure that the appliance is
installed in accordance with these
installation instructions and that the
handle is fitted correctly. Should you
require further assistance please
contact your Miele customer service
centre.Climate range
This appliance is designed for use
within certain climate ranges (ambient
temperatures), and should not be used
outside this range. The climate range of
the appliance is stated on the data
plate inside the appliance.
Climate range Ambient room
temperature
SN
N
ST
T+10 °C to +32 °C
+16 °C to +32 °C
+16 °C to +38 °C
+16 °C to +43 °C
Operating in a room which is too cold
will cause the cooling system to switch
off for too long, causing the internal
temperature in the appliance to rise
with the risk of food deteriorating and
going off.
Ventilation
Air at the back of the appliance gets
warm. The appliance housing unit must
be constructed to allow sufficient space
for ventilation.
Air is taken in through the plinth of the
furniture housing unit.
A ventilation gap of at least 38 mm
depth must be provided behind the
appliance for air to circulate.
The cross-sectional area of the
ventilation gaps and also the
cross-sectional area beneath the
ceiling needs to be at least 200 cm
2to
ensure that warm air can be drawn
through without hindrance. Otherwise
the appliance has to work harder,
resulting in an increase in electricity
consumption.
Installation
33
 
						

							The ventilation gaps must not be
covered or blocked in any way.
They should be dusted on a regular
basis.
Before installing the appliance
^Before installation remove the cover
strip, sealing strip and other
accessories from inside the
appliance and from the external rear
wall of the appliance.
^Do not remove the spacers from the
back of the appliance. These ensure
the gap required between the back
of the appliance and the wall is
maintained.
^
Remove any cable clips from the
back of the appliance.^Remove the red transport fixinga,
and use the stopper suppliedbto
plug the empty hole.
^Check that all parts at the back of the
appliance are unhindered. Carefully
remove any hindrance.
Does your old appliance have
a different hinging
mechanism?
If your old appliance had a different
type of hinging, the furniture door can
still be used. Remove the old hinges
from the housing unit. They are no
longer required because the furniture
door is now fitted to the appliance door.
All the necessary parts are supplied or
can be ordered from the Miele Spare
Parts Department.
Stainless steel front
(depending on model)
The old door can be replaced by a
stainless steel front if required.
Miele can advise you on availability.
Installation
34
 
						

							Niche height [mm]
A
FN 9752 i1772 - 1788
Building-in dimensions
35
 
						

							The door hinges are set ex-works to
enable the doors to be opened wide.
However, if the opening angle of the
door needs to be limited for any reason,
the hinges can be adjusted to
accommodate this.
For example, if the appliance door hits
an adjacent wall when opened, the
opening angle can be limited to 90°.
^Place the locking pins supplied for
limiting the door opening into the
hinges from above.
The door opening angle is now limited
to 90°.
Adjusting the door hinges
36
 
						

							Before building the appliance in, you
will need to decide on which side the
door is to be hinged. If left hand door
hinging is required, follow the
instructions below.
To change the door hinging you will
need the following tools:
–a cross-slotted screwdriver,
–a screwdriver,
–a selection of Torx screwdrivers,
–a spanner.
Appliance door
^Open the appliance door.
^
Remove coversa,bandcwith a
screwdriver.
^
Loosen fixing screwsdat the top
and the bottom slightly.^Slide the door outwards and lift it off
e.
^Unscrew the fixing screwsd
completely, and loosely screw them
in at the top and bottom on the
opposite side of the appliancef.
If you have put locking pins into the
hinges to stop the door opening too far:
^Remove the locking pins from the top
of the hinges.
To remove the soft-close mechanism
^Place the door with the outer side
downwards on a stable surface.
^
Using a screwdriver, carefully push
tension springaoutwards.
Warning. The soft-close mechanism
snaps shut when dismantled.
Danger of injury.
Changing the door hinging
37
 
						

							^Unscrew mountingband pull
soft-close mechanismcdownwards
to remove it.
^Undo ball jointdusing a spanner
and remove it.
^Stand the appliance door up, and
loosen the hinges at the front (the
hinges remain open).
^
Remove screwsa, and use the
stoppers suppliedcto plug the
empty holes.
Do notclose up the hinges. Danger
of injury.
^
Replace the hinges in their diagonally
opposite cornersb.
^
Use a powered screwdriver to secure
the hinges; screwsaare
self-tapping.To secure the soft-close mechanism
^Place the door with the outer side
downwards on a stable surface.
^Screw ball jointdof soft-close
mechanismcinto the new fixing
holes.
^Push tension springainwards
again.
^Screw mountingbonto the hinge
and tighten securely.
^
Open out soft-close mechanismc
and hook it onto ball jointd.
Changing the door hinging
38
 
						

							^Push the appliance door onto the
pre-fitted screws, and then tighten
the screws.
^Replace coversa,bandc.
^
Replace the locking pins into the top
of the hinges to prevent the doors
opening too far.
Changing the door hinging
39
 
						

							All fitting instructions given are for a
right hand hingedappliance. If you
have converted the appliance to left
hand hinging you will need to adapt
these instructions accordingly.
To install the appliance you will need
the following:
–a cross-slotted screwdriver,
–a selection of Torx screwdrivers,
–a hexagon spanner.
Weight of the furniture door
Before fitting a furniture door, ensure
that the weight of the door does not
exceed the maximum permitted:
ApplianceMaximum weight of
furniture door in kg
FN 9752 i 23
Fitting a door which is heavier than
the maximum permitted could
damage the hinges.
Building into a peninsular run
When built into a peninsular run, the
rear of the building-in niche must be
fitted with a kitchen furniture panel.
Aligning the housing unit
The housing unit must be carefully
aligned using a spirit level before
installing the appliance. The unit
corners must be at right angles, as
otherwise the furniture door will not
align correctly with the 4 corners of the
appliance.
Building in the appliance
40