Miele Fn 9752 I Operating And Installation Instructions

Preparing the appliance
^Slide cover stripainto the holder in
the middle of the appliance as
illustrated with the bumps facing
downwards. The bumps will fit into
the keyhole slots.
^Position the mains electricity cable so
that the appliance can be connected
easily once installed.
^
Push the appliance two-thirds of the
way into its niche.
When doing this, make sure that the
mains cable does not get trapped.
^
With 16 mm thick furniture walls:
clip spacersbover the hinges.^Open the appliance door.
^Using a...

^Fit covergonto fixing bracketh.
^Secure fixing brackethto the
bottom of the appliance with screws
i(M5 x 15).
^Carefully remove the protective foil
from sealing stripj.
^Apply the sealing strip to the side of
the appliance on which the door is
opened so that it is flush with the
front edge of the appliance.
Fit the sealing strip so that it meets
up with the lower edge of top cover
dand then cut the sealing strip
2-3mmabove bottom fixing bracket
h.
^
Push the appliance into the niche
until...

On furniture with door fittings (e.g.
stubs, seals etc)the dimension of
these must be taken into account when
making sure there is a gap all round of
42 mm.
^Pull the appliance forwards by the
dimension of the door fitting to keep
the gap at 42 mm all round.
The hinges and the covers will now
protrude by the dimension of the door
fitting.
Tip: Removing the door fittings. This will
ensure that the door is flush with the
surrounding kitchen unit furniture doors.
If the all round gap of 42 mm is not...

^Loosen screwsbon the top and
bottom fixing bracketsc.
^Press fixing bracketcagainst the
side wall and tighten screwsb.
^
Attach fixing bracketcto the
housing unit side wall with screwsd.
Drill holes in the housing unit side
walls if necessary.
^
Break off the protruding end of top
covere, turn the cover around and
fit it on top fixing bracketc.
^
Fit oblong coverfonto top fixing
bracketc.^Break off the protruding end of
bottom covere. It is no longer
required.
^Fit angled covergonto bottom fixing...

^Using a pencil, lightly mark a line
down the centre of the inside of the
furniture door.
^Hang fixing bracketdwith the fitting
aids onto theinsideof the furniture
door. Align the fixing bracket
centrally.
^Attach the fixing bracket securely
using at least 6 short chipboard
screwse(4 x 14 mm). (On cassette
doors only use 4 screws on the
edges).
^
Pull the fitting aids upwards to
remove themf.
^
Turn them around and fit them into
the middle slots on fixing bracketg
for safe keeping.^Hang the furniture...

Securing the appliance door to the
furniture door:
^Screw fixing bracketainto the
pre-drilled holes in the appliance
door using hexagonal screwb.
Make sure the two metal edgesc
are aligned (SymbolII).
^Drill fixing holesdin the furniture
door, and screw in4x14mmscrews
e.
(On large or divided doors, attach a
second pair of fixing bracketsain the
handle region of the door. Use the
pre-drilled holes in the appliance door.)
–
Align depth Z on the furniture door:
Loosen screwsfat the top of the
appliance...

^Replace all the covers.
To make sure the appliance is
correctly fitted:
– The door must close properly.
– The door must not touch the furniture
carcase.
– The seal at the top edge of the
handle side must fit properly.
To double check place a torch in the
appliance and close the doors. Turn the
lights out in the room. If you can see
any light shining out from the sides
double check the installation.
Building in the appliance
47
 

M.-Nr. 07 927 000 / 00Alteration rights reserved / 4910
FN 9752 i