Miele F 9552 I Operating And Installation Instructions

							In the event of a fault which you cannot
correct yourself, or if the appliance is
under guarantee, please contact:
–your Miele Dealer
or
–the Miele Service Department
(see back cover for contact details).
When contacting your Dealer or Miele,
please quote the model and serial
number of your appliance. This
information is given on the data plate
inside your appliance.
Please note that telephone calls may
be monitored and recorded for
training purposes.
Guarantee
For information on the appliance
guarantee specific to your country
please contact Miele. See back cover
for contact details.
In the U.K. your appliance is
guaranteed for 2 years from the date of
delivery. However, you must activate
your cover by calling 08706 080028 or
registering online at www.miele.co.uk.
After Sales / Guarantee
31
 
						

							Electrical connection U.K.
All electrical work should be carried out
by a suitably qualified and competent
person in strict accordance with current
local and national safety regulations
(BS 7671 in the UK).
The appliance is supplied with a mains
cable and moulded plug ready for
connection to an a.c. single phase
220-240 V 50 Hz supply.
Please ensure that the connection data
quoted on the data plate match the
household mains supply.
Connection should be made via a
suitable switched socket which is easily
accessible. For extra safety it is
advisable to install a suitable residual
current device (RCD).
Do not connect the appliance to the
mains electricity supply by an extension
lead. Extension leads do not guarantee
the required safety of the appliance
(e.g. danger of overheating).
The appliance must not be connected
to an inverter and must not be used
with a plug adapter as these can cause
damage to the appliance’s electronic
unit.Non-rewireable plugs (BS 1363)
The fuse cover must be re-fitted when
changing the fuse, and if the fuse cover
is lost, the plug must not be used until a
suitable replacement is obtained. The
colour of the correct replacement cover
is that of the coloured insert in the base
of the plug, or the colour that is
embossed in words in the base of the
plug (as applicable to the design of the
plug fitted).
Replacement fuses should be ASTA
approved to BS 1362 and have the
correct rating. Replacement fuses and
fuse covers may be purchased from
your local electrical supplier.
WARNING
THIS APPLIANCE MUST BE
EARTHED
Electrical connection
32
 
						

							This appliance must be built in,
otherwise it could tip up.
Location
The appliance should be installed in a
dry, well-ventilated room.
The room temperature should not go
above or below the climate range for
which the appliance is designed.
The higher the ambient temperature of
the room, the more energy the
appliance requires to operate.
It should not be installed where it is
exposed to direct sunlight or directly
adjacent to a heat-producing appliance
such as an oven or a radiator.
Climate range
The appliance is designed for use
within certain climate ranges (ambient
temperatures), and should not be used
outside this range. The climate range of
the appliance is stated on the data
plate inside the appliance.
Climate range Ambient room
temperature
SN, N
ST
Tup to +32 °C
up to +38 °C
up to +43 °C
The appliance will function perfectly
down to an ambient temperature of
+5 °C.
Ventilation
Air at the back of the appliance gets
warm. The appliance housing unit must
be constructed to allow sufficient space
for ventilation.
A ventilation gap of at least 38 mm
depth must be allowed for behind the
appliance for air to circulate. The air
inlet to the appliance is via the plinth in
the housing unit.
The cross-section of the air inlet and
outlet must be at least 200 cm
2to
ensure that air can circulate without
hindrance. Otherwise the appliance has
to work harder, resulting in an increase
in electricity consumption.
The air inlet and outlet must not be
covered or blocked in any way.
They should be dusted on a regular
basis.
Installation
33
 
						

							Before installation
^Before installation remove the cover
strip, sealing strip and other
accessories from inside the
appliance and from the external rear
wall of the appliance.
^On no account should the spacers
be removed from the back of the
appliance. These ensure the gap
required between the back of the
appliance and the wall is maintained.
^Remove any cable clips from the rear
of the appliance.
^Check that all parts at the back of the
appliance are unhindered. Carefully
remove any hindrance.
Does your old appliance have
a different hinging
mechanism?
If your old appliance had a different
type of hinging, the furniture door can
still be used. Remove the old hinges
from the housing unit. They are no
longer required because the furniture
door is now fitted to the appliance door.
All the necessary parts are supplied or
can be ordered from the Miele Spare
Parts Department.
Stainless steel front
(depending on model)
The old door can be replaced by a
stainless steel front if required.
This is available from your dealer or the
Miele Spare Parts Department.
Installation
34
 
						

							Niche height [mm]
A
F 9252 i874 – 890
F 9552 i1397 - 1413
Building-in dimensions
35
 
						

							The door hinges are set ex-works to
enable the door to be opened wide.
However, if the opening angle of the
door needs to be limited for any reason,
the hinge can be adjusted to
accommodate this.
–For example, if the appliance door
hits an adjacent wall when opened,
the opening angle can be limited to
90°.
^Place the locking pins supplied for
limiting the door opening into the
hinges from above.
The door opening angle is now limited
to 90°.–If you would like the appliance door
to be cushioned so that it opens
more softly, the spring tension on the
appliance door can be adjusted.
To do this, use the allen key supplied to
adjust the door hinges.
aTo reduce the opening angle:
^
Turn the allen key clockwise.
This tightens the hinges and makes it
harder to open the door wide.
bTo open the door fully:
^
Turn the allen key anticlockwise.
Adjusting the door hinges
36
 
						

							Before building the appliance in, you
will need to decide on which side the
door is to be hinged. If left hand door
hinging is required, follow the
instructions below.
To change the door hinging you will
need the following tools:
–a cross-slotted screwdriver,
–a screwdriver,
–a selection of Torx screwdrivers,
–a spanner.
Appliance door
^Open the appliance door.
^
Remove coversa,bandcwith a
screwdriver.
^
Loosen fixing screwsdat the top
and the bottom slightly.^Slide the door outwards and lift it off
e.
^Unscrew the fixing screwsd
completely, and loosely screw them
in at the top and bottom on the
opposite side of the appliancef.
If you have put locking pins into the
hinges to stop the door opening too far:
^Remove the locking pins from the top
of the hinges.
To remove the soft-close mechanism
^Place the door with the outer side
downwards on a stable surface.
^
Open the hinges, and loosen the
screw in mountinga.
Warning. The soft-close mechanism
snaps shut when dismantled.
Danger of inury.
Changing the door hinging
37
 
						

							^Unscrew ball jointbusing a
spanner, and remove soft-close
mechanismctogether with the ball
joint.
Do not separate the soft-close
mechanism from the ball joint. This
would damage the mechanism.
^
Stand the appliance door up, and
loosen the hinges at the front (the
hinges remain open).
^
Remove screwsa, and use the
stoppers suppliedcto plug the
empty holes.
Do notclose up the hinges. Danger
of inury.^Replace the hinges in their diagonally
opposite cornersb.
^Use a powered screwdriver to secure
the hinges; screwsaare
self-tapping.
To secure the soft-close mechanism
^Place the door with the outer side
downwards on a stable surface.
^Screw ball jointsbof soft-close
mechanismcinto the new fixing
holes.
^
Open out soft-close mechanismc,
and hook mountingaonto the hinge.
^
Hold the soft-close mechanism in this
position, and screw mountingato
the hinge.
Changing the door hinging
38
 
						

							^Push the appliance door onto the
pre-fitted screws, and then tighten
the screws.
^Replace coversa,bandc.
^
Replace the locking pins into the top
of the hinges to prevent the doors
opening too far.
Changing the door hinging
39
 
						

							All fitting instructions given are for a
right hand hingedappliance. If you
have converted the appliance to left
hand hinging you will need to adapt
these instructions accordingly.
To install the appliance you will need
the following:
–a cross-slotted screwdriver,
–a selection of Torx screwdrivers,
–a hexagon spanner.
Weight of the furniture door
Before fitting a furniture door, ensure
that the weight of the door does not
exceed the maximum permitted:
ApplianceMaximum weight of
furniture door in kg
F 9252 i 20
F 9552 i 20
Fitting a door which is heavier than
the maximum permitted could
damage the hinges.
Building into a peninsular run
When built into a peninsular run, the
rear of the building-in niche must be
fitted with a kitchen furniture panel.
Aligning the housing unit
The housing unit must be carefully
aligned using a spirit level before
installing the appliance. The unit
corners must be at right angles, as
otherwise the furniture door will not
align correctly with the 4 corners of the
appliance.
Building in the appliance
40