Miele F 9212 I Operating And Installation Instructions

							Niche height [mm]
A
F 9212 i874 - 890
Building-in dimensions
31
200 cm2
A
2100
200 cm238
560-568
550
[mm]
 
						

							Before building the appliance in, you
will need to decide on which side the
door is to be hinged. If left hand door
hinging is required, follow the
instructions below.
To change the door hinging, you will
need various sizes ofTorx
screwdriversand aslotted
screwdriver.
Appliance door
^Open the appliance door.
^
Pull off coversaandb.
^
Unscrew hinge pinc.
^
Tilt the door, and lift it off.
^
Unscrew hinge plated, and replace
it on the opposite side using the
same screws.
^
Remove lower hinge pinetogether
with washerf, and replace these on
the opposite side.^Replace the appliance door on lower
hinge pine.
^Insert upper hinge pincinto the
outerhole in hinge plated, and
screw securely into the top of the
door.
^Replace coversaandbon the
opposite side, turning them by 180 °.
Changing the door hinging
32
 
						

							All building-in instructions given are
for aright hand hingedappliance.
If you have converted the appliance
to left hand hinging you will need to
adapt these instructions
accordingly.
Building into a peninsular run
When built into a peninsular run, the
rear of the building in niche must be
fitted with a kitchen furniture panel.
Aligning the housing unit
Before installing the appliance, the
housing unit must be carefully aligned
using a spirit level. The housing unit
corners must be at right angles, as
otherwise the appliance furniture door
will not align correctly with the 4
corners of the unit. Align the furniture
door with the hinges.
Preparing the appliance
^Slide cover stripainto the holder as
shown, with the bumps facing
downwards. The bumps will fit into
keyhole slotsb. The cover strip is
then flush with the side of the
appliance on which the door is
openedc.
Building in the appliance
33
 
						

							Building in the appliance
^Remove covera.
^Secure bracketbwith screwsc
(4.8 x 16 mm).
^
Push the appliance into the
building-in niche, leaving a gap of
approx. 4 mm.
Take care not to trap the mains
cable.
^
Push in the appliance until the front
edges of bracketband hinge plates
dandeare flush with the front
edge of the housing.^Align the appliance height from above
on both sides using adjusting screw
f.
^Plug the gap between the appliance
and the furniture wall on the door
opening side with sealing stripg.
Press the sealing strip into the gap
starting at the bottom, and cut to
length so that it fits snugly to the
lower edge of bracketb.
Building in the appliance
34
 
						

							Securing the appliance and
fitting the furniture door
^Push the appliance against the
housing wall on the side on which the
door opens so that the sealing strip is
pressed into the housing wallh.
^
Secure the appliance at the top with
screwi(4 x 19 mm) into bracketb,
pushing the appliance against the
furniture wall as you do so, then
secure it at the bottom with screwsj
(4 x 36 mm) through the adjusting
screws in the hinge plates on the
housing.
^
Tighten all the screws.
^
If necessary, align cover stripkby
pushing it parallel to the top of the
unit - it should not protrude.
^
Fold in the side section of bracketb.^Replace covera, and cap all the
holes with stopperslandm.
^Secure door fixingsnto the
appliance door with screwo
(3.9 x 9.5 mm), to suit the position of
the handle.
Very large doors will require several
door fixings.
^Open the door right out, and push
fixing guidespinto door fixingsn.
^Position the furniture door onto the
appliance door, and secure fixing
guidespto the furniture door using
screwsq(4 x 14 mm). Maintain a
distance d (= the thickness of the
housing unit walls) between the edge
of the appliance door and outer edge
of the furniture door.
^Align the door fixing so that the
furniture door on the side with the
handle does not lie against the
housing unit wall when the door is
shut. Aminimum distance of 1 mm
must be maintained.
^
Cap the empty holes on the
appliance door with stoppersr
supplied; this is vital for the long-term
effectiveness of the insulation.
Building in the appliance
35
 
						

							Alteration rights reserved / 4911
F 9212 iM.-Nr. 09 275 610 / 00