Miele F 1811 Vi Operating And Installation Instructions

							Electrical connection U.K.
All electrical work should be carried out
by a suitably qualified and competent
person in strict accordance with current
local and national safety regulations
(BS 7671 in the UK).
The appliance is supplied with a mains
cable and moulded plug ready for
connection to an a.c. single phase
220-240 V 50 Hz supply.
Please ensure that the connection data
quoted on the data plate match the
household mains supply.
Connection should be made via a
suitable switched socket which is easily
accessible. For extra safety it is
advisable to protect the appliance with
a suitable residual current device
(RCD).
Do not connect the appliance to the
mains electricity supply by an extension
lead. Extension leads do not guarantee
the required safety of the appliance
(e.g. danger of overheating).
This appliance must not be connected
to the inverter of an autonomous power
supply, e.g. a solar power system.
When switching the appliance on, a
surge in power could trigger the safety
cut-out mechanism. This could damage
the electronic unit.
The appliance must not be used with
so-called energy saving devices. These
reduce the energy supply to the
appliance which could then become
too warm. Using such devices could
alter the specification of the product.Non-rewireable plugs (BS 1363)
The fuse cover must be re-fitted when
changing the fuse, and if the fuse cover
is lost, the plug must not be used until a
suitable replacement is obtained. The
colour of the correct replacement cover
is that of the coloured insert in the base
of the plug, or the colour that is
embossed in words in the base of the
plug (as applicable to the design of the
plug fitted).
Replacement fuses should be ASTA
approved to BS 1362 and have the
correct rating. Replacement fuses and
fuse covers may be purchased from
your local electrical supplier.
WARNING
THIS APPLIANCE MUST BE
EARTHED
Electrical connection
51
 
						

							Location
This appliance should be installed in a
dry, well-ventilated room. It should not
be installed where it is exposed to
direct sunlight or directly adjacent to a
heat-producing appliance such as an
oven or a radiator. The room
temperature should not go above or
below the climate range for which the
appliance is designed. The higher the
ambient temperature of the room, the
more energy the appliance requires to
operate.
If installation near a heat source is
unavoidable, observe the following
distances between the appliance and
the heat source:
– 3 cm away from an electric oven or
cooker
– 30 cm away from an oil- or coal-fired
range.Important: tropical / humid
environments
During periods of high humidity,
some condensation may appear on
outside surfaces of cooling
appliances. This condensation will
disappear when humidity levels
drop. For prevention, it is advisable
to install the appliance with sufficient
ventilation in a dry and/or an
air-conditioned room.
Please ensure that doors are closing
and sealing properly.
Please ensure that the appliance is
installed in accordance with these
installation instructions and that the
handle is fitted correctly. Should you
require further assistance please
contact your Miele customer service
centre.
Climate range
The appliance is designed for use
within certain climate ranges (ambient
temperatures) and should not be used
outside this range. The climate range of
the appliance is stated on the data
plate inside the appliance.
Climate range Ambient room
temperature
SN
N
ST
T+10 °C to +32 °C
+16 °C to +32 °C
+16 °C to +38 °C
+16 °C to +43 °C
Operating in a room which is too cold
will result in the cooling system
switching off for too long, causing the
internal temperature in the appliance to
rise with the risk of food deteriorating
and going off or frozen food defrosting.
Installation advice
52
 
						

							Safe operation of the appliance is
only assured if it has been installed
and connected in accordance with
these operating and installation
instructions.
Warning!
This appliance is very heavy and
can tip forwards when the door is
open. Keep the door shut until the
appliance has been built in and
secured within the building-in niche
in accordance with these
instructions.
Due to the size and weight of the
appliance, installation must be
carried out by two people.
The weight of the appliance when
empty is:
F 1811 Vi.................. 191kg
F 1911 Vi..................208kg
Installation advice
53
 
						

							Floor
To ensure the safe installation of the
appliance and to guarantee its correct
functioning, the floor to the niche where
the appliance is to be installed must be
smooth and even.
It must be made from strong, rigid
material.
The appliance is extremely heavy when
fully loaded, and for this reason it is
imperative that the floor it stands on is
able to bear its weight. If necessary, the
advice of an architect or structural
engineer should be sought.
When fully loaded, the approx. weight
of the appliance is:
F 1811 Vi.................. 430kg
F 1911 Vi..................510kg
Door hinging
The appliance is supplied with fixed
hinges. If you need to change the
door hinging to the other side,
please contact the Service
Department.
On no account should you attempt
to change the door hinging yourself.
(N.B. Door hinge change not
available in all countries).
Adjoining furniture/units
The appliance is screwed to the
adjoining furniture/units to the side and
above.
For this reason, it is essential that all
furniture/units be fixed to the ground
and/or wall.
Ventilation
The ventilation gaps must not be
covered or blocked in any way.
They should be dusted on a regular
basis.
Installation advice
54
 
						

							Side-by-side installation
This appliance may be installed
side-by-side with another suitable
refrigerator or freezer.
A side-by-side installation kit,
available from Miele, is required.
Ask your dealer which appliances
are suitable for side-by-side
installation with this appliance.
See the instructions supplied with
the side-by-side installation kit for
how to fix the appliances together.
Joining the two appliances together
with the side-by-side installation kit
If the appliances are to be installed
next to each other without a partition
wall between them, they will need to be
joined together using the side-by-side
installation kit.Installation with a partition wall using
the side-by-side installation kit
The partition wall must be at least
16 mm thick.
If the partition wall between the two
appliances isbetween 16 mm and
160 mmthick, each appliance must be
built into its own niche using the
assembly parts supplied. The
side-by-side installation kit is also
required.
Installation with a partition wall
without the side-by-side installation
kit
If the partition wall between the two
appliances ismore than 160mm, each
appliance must each be built into its
own niche using the assembly parts
supplied (without using the
side-by-side installation kit).
Installation advice
55
 
						

							Appliance door dimensions (opening angle 115°)
AB CD
F 1811 Vi829 mm Door front (max. 38 mm)* Door handle* 363 mm
F 1911 Vi982 mm Door front (max. 38 mm)* Door handle* 428 mm
* The dimensions for the door fronts and handles will vary according to the
individual kitchen.
Miele recommends using the full door opening angle of 115° for this freezer.
Installation advice
56
 
						

							Niche width
A
F 1811 Vi762 – 765 mm
F 1911 Vi915 – 918 mm
Building-in dimensions
57
 
						

							Laying the electrical cabling
and the pipework for the mains
water supplyDoor front dimensions
AB
F 1811 Vi2029 mm 756 mm
F 1911 Vi2029 mm 908 mm
Building-in dimensions
58
 
						

							Due to the size and weight of the
appliance, it is essential that
installation is carried out by two
people.
Tools and accessories
required
–Cordless screwdriver
–Torx screwdriver
–Hammer drill
–Drill bits in various sizes, depending
on materials
– Hammer
– 8 mm socket wrench
– Adhesive tape
– Pipe wrench
– Spirit level
– Try-square
To secure the housing unit to a wall
behind:
–
suitable wall plugs/fixing screws for
the type and material of the wall.Other
–Step ladder
–Sack barrow
–Wooden beams (min. 75 mm x
100 mm) if required, to prevent
tipping; length depends on width of
building-in niche
–Wood screws in various sizes
Optional accessory
–Side-by-side installation kit for
side-by-side installation of two
appliances
Installation
59
 
						

							Stainless steel fronts
Stainless steel fronts and stainless steel
look plinth grilles are available from
your dealer or the Miele Spare Parts
Department.
Weight of the door front
Before fitting the door front, ensure that
the weight of the fronts does not
exceed the maximum permitted:
Appliance Max.
weight
of door front in kg
F 1811 Vi 48
F 1911 Vi 36
Fitting a door front which is heavier
than the maximum permitted could
damage the hinges.
Building into a peninsular run
When built into a peninsular run, the
rear of the building-in niche must be
fitted with a kitchen furniture panel.
Building-in at the end of a run
of units
If one side of the appliance is visible, a
side panel is required.
The side panel must be fixed to the
wall, the floor and any furniture/units
above before the appliance is placed in
the niche.
The size of the side panel must match
that of the furniture panel opposite.
Installation
60