Miele Da 420 V Manual

Before any cleaning or maintenance
work is carried out, disconnect the
cooker hood from the mains supply.
Ensure that:
- it is switched off at the isolator,
or
- the fuse is withdrawn from the
fused spur connection unit, or
- the mains fuse is disconnected,
or
- the screw-out fuse is removed (in
countries where this is
applicable).
E-Cloth
A microfibre "E-Cloth" is available
from the Miele UK Spare Parts
Department, which is suitable for
cleaning surfaces such as stainless
steel, glass, plastic...

Important for appliances with
lacquered housing
(special order finish)
It is very difficult to clean this type of
surface without causing minor marks to
the surface material. This can become
particularly noticeable with darker
colours and if there is halogen lighting
in the kitchen.
Important for the controls
The controls may suffer
discolouration or damage if soiling is
left on them for too long.
Remove soiling straight away.
Observe the General notes on cleaning
earlier in this section.
Do not use...

Cleaning the grease filters by hand
Clean the filters with a soft nylon
brush in a mild solution of hot water
and a little washing-up liquid.
Do not use "neat" washing up liquid.
Do not use:
–cleaning agents containing
descaling agents,
–powder cleaners, cream cleaners or
abrasive all-purpose cleaning
agents,
–oven sprays.
Cleaning the grease filters in the
dishwasher
Place the filters as upright as
possible in the lower basket, with the
short sides upright, and wash on a
65°C programme,...

Charcoal filter
(...U models only)
If the cooker hood is connected for
recirculation, a charcoal filter must be
inserted in addition to the grease filters.
This is designed to absorb cooking
odours.
It is fitted in the canopy above the
grease filters.
New filters can be purchased from
your Miele dealer or from the Miele
Spare Parts Department.
See back cover for contact details,
and "Technical data" for the model
number of the filter.
Before fitting or replacing a charcoal
filter, the grease...

Changing a halogen lamp
Before any cleaning or maintenance
work, disconnect the cooker hood
from the mains supply. Ensure that
–it is switched off at the isolator, or
–the screw-out fuse is removed (in
countries where this is applicable).
Exercise caution when changing
halogen lamps. They get very hot
during use and remain hot for some
time after being switched off. Let
them cool down before you change
them.
Do not touch the surface directly
when changing a lamp, as grease
particles from your fingers...

DA 420-4, DA 420-4 EXT
DA 424-4, DA 424-4 EXTDA 420-4 U
1) Cut-out for feeding through the
exhaust ducting, the mains cable and,
with ...EXT models, the connection
cable to the external motor
In recirculation mode, only the mains
cable is required.
Exhaust connection150 mm (not
needed for recirculation mode)
Appliance dimensions
26 

Safety distance between hob and
cooker hood
Theminimumsafety distances
between the top of a cooker or hob
and the bottom of the cooker hood
are as follows, unless a greater
distance is specified by the
manufacturer of your cooking
appliance:
550 mm above electric hobs and
cookers,
650 mm above an open grill or
deep fat fryer,
650 mm above gas hobs and
cookers.
If this cooker hood is installed above
a Miele Wok CS 1028 CombiSet
appliance, a minimum safety
distance of 760 mm must be
maintained between the...

Before installation, it is important to
read the information given on the
following pages as well as the
"Appliance dimensions" and the
"Warning and Safety instructions" at
the beginning of this booklet.
This is particularly crucial when
using the cooker hood at the same
time as a heating appliance that
relies on oxygen from the same
room to avoid the danger of toxic
fumes building up.
Installation instructions
See enclosed Installation sheet for
instructions on how to install this...

Important: To avoid the danger of
toxic fumes, please observe the
Warning and Safety instructions.
This is especially crucial when using
the cooker hood at the same time as
another heating appliance which
relies on air from the same room.
The cooker hood should be installed
according to local and national
building regulations. Seek approval
from the building inspector where
necessary.
–All ducting, pipework and fittings
must be of non-flammable materials.
– The exhaust ducting should be as
short and...

Important!
If the exhaust ducting is to run through
rooms, ceiling space etc. where there
may be great variations in temperature
between the different areas, the
problem of condensation will need to
be addressed. The exhaust ducting will
need to be suitably insulated.
Condensate trap
(optional accessory)
In addition to insulating the exhaust
ducting, we recommend that a suitable
condensate trap is also installed to
collect and evaporate any condensate
which may occur. Condensate traps
are available...