Midway Touch Master Infinity Touchscreen Replacement Sheet Manual
Have a look at the manual Midway Touch Master Infinity Touchscreen Replacement Sheet Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 192 Midway manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
midway amusement games, llc 3401 north california avenue chicago, illinois 60618 usa http://www.midwaygames.com MARCH 2000 16-11151 TOUCHSCREEN REPLACEMENT FOR INFINITY ® COUNTERTOP MODELS Access Touchscreen 1. Turn off AC power. Unplug line cord. Refer to original manual for details or illustrations on any of the following instructions. 2. 5($5 225Insert key into Rear Door and turn 90 degrees clockwise to unlock. Remove two screws securing door. Swing door on hinge, remove, and set aside. 3. 723 &29(5Remove three right screws from rear of Top Cover Assem- bly. Gently pull Top Cover Assembly downward two or three inches along slope of Base Assembly, but do not remove. Pivot Top Cover Assembly to expose fan wire. Disconnect fan wire. Remove Top Cover Assembly and set aside. 4. ()/(&7,21 %5$&.(7Remove Deflection Board Bracket screw nearest Coin Meter. Loosen Bracket screws holding plate on opposite side from coin meter, but do not remove. Lift rear of Bracket until spring-loaded pin near Touchscreen snaps into hole in side panel wall. 5. 728&+6&5((1 &21752//(5Pry Touchscreen Controller box from Power Supply side wall and disconnect Touchscreen Connector Cable from Controller box. Unplug power connector and remove ground lug. 6. (/(&7521,&6 $66(0%/,(6Disconnect Hard Disk Drive ribbon connector. Remove screw in rear center of Electronics Tray. Grasp Tray by vertical lip at bottom. Disconnect power cables and other wiring as you slowly slide Tray out of cabinet. 7. ()/(&7,21 %5$&.(7Push in spring-loaded pin and swivel Bracket to down position. 8. &57 %(=(/Remove #8 nuts from inside bottom of CRT mounting bracket. (Do not remove nut holding cable clamp.) Hold Bezel in place while removing screws holding top of Bezel. Lift Bezel and foam gasket up and off Base Assembly. Contents of Touchscreen Replacement Kit A-23751 04-13018 Touchscreen w/ connector cable23-6825 Double-sided foam tape adheres Touch- screen to CRT.RM-62-01 Rubber tape keeps moisture out of gap between Touch- screen and CRT .20-10413 Foam Bezel Gasket fills gap between Touchscreen and Bezel.16-10416 Sheet describes Touch- screen cleaning.RM-42-01 and RM-43-01 Hook and Loop fastener holds Control- ler box to wall. 20-10413 04-13018RM-62-01 23-6825
page 2 Remove Touchscreen 1.7$3( Remove moisture-barrier tape from Touchscreen edge. Hold Touchscreen in place as you do this to prevent it from falling. Note that Touchscreen cable is near coin slot. 2. Separate Touchscreen from CRT. 3. Peel foam tape from CRT perimeter. 4.&57 Clean CRT by applying a mixture of isopropyl alcohol and water to a clean cloth or sponge. Do not apply cleaner directly on glass. 5. Remove foam gasket from Bezel. Mount New Touchscreen 1..,7 Unpack contents of replacement kit. 2. Install new foam gasket inside Bezel. 3.7$3( Remove foam tape backing and place on perimeter of CRT. Route cable past CRT. 4.728&+6&5((1 Hold Touchscreen by edges and clean with alcohol. Orient cable toward coin slot. Press firmly against foam tape to set adhesive. 5. Carefully seal edges where Touchscreen meets CRT with rubber moisture-barrier tape. 6. Place Bezel and foam gasket back on cabinet. 7. Pivot Deflection Board, if needed. If hook- and-loop fastener holding Touchscreen Con- troller box to side wall is in disrepair, replace. Connect Touchscreen Connector into Touch- screen Controller box. Plug in power connector and ground lug. Reattach Controller box to side wall. Lower Deflection Board, if needed. Replace Components 1.%(=(/ Reinstall top screw and nut near coin slot, then top screw and nut on opposite side from coin slot. Reinstall lower screws and nut in any order. 2.(/(&7521,&6 75$
midway amusement games, llc 3401 north california avenue chicago, illinois 60618 usa http://www.midwaygames.com MARCH 2000 16-11151 TOUCHSCREEN REPLACEMENT FOR INFINITY ® COUNTERTOP MODELS Access Touchscreen 1. Turn off AC power. Unplug line cord. Refer to original manual for details or illustrations on any of the following instructions. 2. 5($5 225Insert key into Rear Door and turn 90 degrees clockwise to unlock. Remove two screws securing door. Swing door on hinge, remove, and set aside. 3. 723 &29(5Remove three right screws from rear of Top Cover Assem- bly. Gently pull Top Cover Assembly downward two or three inches along slope of Base Assembly, but do not remove. Pivot Top Cover Assembly to expose fan wire. Disconnect fan wire. Remove Top Cover Assembly and set aside. 4. ()/(&7,21 %5$&.(7Remove Deflection Board Bracket screw nearest Coin Meter. Loosen Bracket screws holding plate on opposite side from coin meter, but do not remove. Lift rear of Bracket until spring-loaded pin near Touchscreen snaps into hole in side panel wall. 5. 728&+6&5((1 &21752//(5Pry Touchscreen Controller box from Power Supply side wall and disconnect Touchscreen Connector Cable from Controller box. Unplug power connector and remove ground lug. 6. (/(&7521,&6 $66(0%/,(6Disconnect Hard Disk Drive ribbon connector. Remove screw in rear center of Electronics Tray. Grasp Tray by vertical lip at bottom. Disconnect power cables and other wiring as you slowly slide Tray out of cabinet. 7. ()/(&7,21 %5$&.(7Push in spring-loaded pin and swivel Bracket to down position. 8. &57 %(=(/Remove #8 nuts from inside bottom of CRT mounting bracket. (Do not remove nut holding cable clamp.) Hold Bezel in place while removing screws holding top of Bezel. Lift Bezel and foam gasket up and off Base Assembly. Contents of Touchscreen Replacement Kit A-23751 04-13018 Touchscreen w/ connector cable23-6825 Double-sided foam tape adheres Touch- screen to CRT.RM-62-01 Rubber tape keeps moisture out of gap between Touch- screen and CRT .20-10413 Foam Bezel Gasket fills gap between Touchscreen and Bezel.16-10416 Sheet describes Touch- screen cleaning.RM-42-01 and RM-43-01 Hook and Loop fastener holds Control- ler box to wall. 20-10413 04-13018RM-62-01 23-6825
page 2 Remove Touchscreen 1.7$3( Remove moisture-barrier tape from Touchscreen edge. Hold Touchscreen in place as you do this to prevent it from falling. Note that Touchscreen cable is near coin slot. 2. Separate Touchscreen from CRT. 3. Peel foam tape from CRT perimeter. 4.&57 Clean CRT by applying a mixture of isopropyl alcohol and water to a clean cloth or sponge. Do not apply cleaner directly on glass. 5. Remove foam gasket from Bezel. Mount New Touchscreen 1..,7 Unpack contents of replacement kit. 2. Install new foam gasket inside Bezel. 3.7$3( Remove foam tape backing and place on perimeter of CRT. Route cable past CRT. 4.728&+6&5((1 Hold Touchscreen by edges and clean with alcohol. Orient cable toward coin slot. Press firmly against foam tape to set adhesive. 5. Carefully seal edges where Touchscreen meets CRT with rubber moisture-barrier tape. 6. Place Bezel and foam gasket back on cabinet. 7. Pivot Deflection Board, if needed. If hook- and-loop fastener holding Touchscreen Con- troller box to side wall is in disrepair, replace. Connect Touchscreen Connector into Touch- screen Controller box. Plug in power connector and ground lug. Reattach Controller box to side wall. Lower Deflection Board, if needed. Replace Components 1.%(=(/ Reinstall top screw and nut near coin slot, then top screw and nut on opposite side from coin slot. Reinstall lower screws and nut in any order. 2.(/(&7521,&6 75$< Reconnect wires to Electronics Assembly and slide Tray in cab- inet. Fasten with screw in rear center of Tray. Reconnect Hard Disk Drive ribbon connector. 3.723 &29(5 $66(0%/< Align Top Cover on Base Assembly close enough to reat- tach fan cable. Slide Top Cover Assembly fully onto Base Assembly. Take care not to pinch fan cable. Fasten and tighten three screws. 4.5($5 225 Insert bottom hinges of Door and swing closed. Turn key 90 degrees counterclockwise to lock. Reinstall screws. Calibrate Touchscreen 1. Plug in line cord and turn AC power on. 2.6,( &29(5 Insert key into rear lock of Side Cover Assembly and turn 90 degrees to unlock. Grasp hook and pull down along slope of Base Assembly. Set Cover aside. 3. Press CAL. pushbutton to calibrate and test new Touchscreen. 4.723 &29(5 Slide Cover back onto Base Assembly. Turn key 90 degrees clockwise to lock. 5. If Touchscreen does not work, refer to Trouble- shooting Chapter of original manual. TEST SWITCH SIDE COVER ASSEMBLYCAL. SWITCH REAR DOOR DEFLECTION BOARD BRACKET BASE ASSEMBLY TOP COVER ASSEMBLY FAN COIN METER FAN CABLE