Midway Touch Master Infinity Countertop Led Panel Installation Manual

							M
IDWAY
 A
MUSEMENT
 G
AMES
, LLC
3401 N. C
ALIFORNIA
 A
VENUE
 C
HICAGO
, I
LLINOIS
 60618 USA
HTTP
://
WWW
.MIDWAY
.COM
JUNE 2000
16-11170.1
Update Hard DriveRefer to sheet 16-11081.2 (or most recent version), “CD-ROM Upgrade Instructions.”Reinstall Doors and Covers1. Hold Top Cover Assembly, with Mounting Bracket, in place over Base Assembly close 
enough to reconnect fan cable.
2. Slide Top Cover Assembly fully onto Base Assembly. Do not pinch cables.
3. Fasten three screws and tighten Top Cover to Base Assembly.
4. Run LED data cable through rear door opening and along cash chamber back wall into cash 
chamber. Connect into RJ25 port on DB9 to RJ11 Adapter.
5. Slide Side Cover Assembly onto Base Assembly. Turn key 90 degrees counter-clockwise.
6. Route modem cable and LED data cable through notch in Rear Door. Bundle extra data cable 
to DB9 to RJ11 Adapter with tye wrap. Insert bottom hinges of Rear Door into Base Assembly 
and swing Door closed. Turn key 90 degrees counter-clockwise to lock. Reinstall screws. 
COVER AND DOOR REMOVAL AND REPLACEMENT
Plug in Equipment1. Plug in Touchmaster Infinity line cord into receptacle on cabinet rear and AC outlet.
2. Wrap LED power supply cord around ferrite bead twice, then pass it through bead. Close bead 
and plug LED power supply into the nearest receptacle.
3. If necessary, plug the supply into a suitably listed power strip or cord set. Make sure supply 
connection is rated appropriately. Ensure all connections are in compliance with National 
Electrical Code, NPFA 70 and local authorities having jurisdiction.
COUNTERTOP 
LED PANEL 
INSTALLATION
Item Part No. Qty Item Part No. Qty
LED Display & Power Cable 20-10735 1 LED Mounting Bracket 04-13083 1
LED Data Cable (7’) 20-10737 1 Adhesive Footing 23-6830 4
Ferrite Bead 5556-16550-00 2 Tye Wrap (4”) 03-10047 12
ESNA Nut 4410-01132-00 2 Mounting Clip 01-15309 2
#8x5/8 Torx screw 4108-01193-10B 4 Internal Serial Cable 04-12941.1 1
6-32x1/2 Torx screw 4006-01100-08 4 Ser. Port Mount. Brckt 01-14556 1
8-32x3/8 pin head screw 4008-01227-06 1 1/4 Spacer 03-6047-1 2
4-40x1 pin head screw 4004-01005-16 2 DB9-RJ11 Adapter 20-10736.1 1
MTN logo 31-3646 1 RJ11 cable coupler 20-10734 1
CD-ROM Update Instructions 16-11081.2 1 Tee adapter 20-10657 1
Update CD-ROMs (3) 04-13091 1 Modem cable (20’) 20-10631 1
MTN Handbook 16-11184 1 CD-ROM Update cable 20-10670-1 1
Key T-20 20-9620 1 Key T-10 20-9642 1
“All Ages” decal 16-10419.1-1 1 “Sexual Content Strong” decl 16-10419.1-8 1Inspect components for damage before assembling. The following is a list of the most vital components.
INTERIOR WALL
SIDE COVER ASSEMBLYBASE ASSEMBLY
REAR DOOR TOP COVER ASSEMBLY
LED DATA CABLESUPPLY CASH CHAMBER
LED POWER
FERRITE
BEAD 
						

							Access Cabinet Interior (See illustration on back page)1. Turn AC power off and unplug line cord.
2. Insert key into rear lock of Side Cover Assembly. Turn key 90 degrees clockwise to unlock.
3. Grasp hook and pull down along base assembly. Set cover aside. Remove cash vault and set aside.
4. Remove two screws that secure Rear Door.
5. Insert key into Rear Door. Turn key 90 degrees clockwise to unlock.
6. Rear Door is hinged at bottom. Swing Door on hinge, remove, and set aside.
7. Remove three right screws from rear of Top Cover Assembly.
8. Gently pull Assembly downward two or three inches along Base Assembly and pivot enough to expose 
fan wire. Disconnect fan wire.
9. Remove Top Cover Assembly and set in safe place.Install Connector 
Bracket1. Line up Serial Port Mounting 
Bracket with hole in interior wall. 
Install 8-32x3/8 screw and tighten.
2. Insert 1” screws all the way through 
DB9-RJ11 Adapter. Place spacers 
on exposed ends of screws.
3. Hold DB9 connector of Internal 
Serial Cable to Serial Port Mount-
ing Bracket, oriented as in illustra-
tion at right.
4. Fasten DB9-RJ11 Adapter to Serial 
Cable with 1” screws through 
Mounting Bracket.Connect Cable to 
Electronics1. Route two free connectors of 
internal 
Serial Cable through large 
hole in interior wall.
2. Connect Cable to Dolphin 
Board at
“SER_PORT” socket and to 
NLX Riser Board at “FA N” 
socket. 
Install Modem Cable1. Determine distance to telephone jack. If needed, use RJ25 voice coupler and 25 ft. modem cable in 
addition to cable that was factory installed into the modem port.
2. If desired, plug Telephone Tee adapter into telephone wall jack and plug telephone line into one port.
3. Plug modem cable into telephone wall jack or remaining port in Tee adapter.
4. Route cable along floor, walls, posts, etc. safely out of way of pedestrian traffic.Prepare Top Cover/Mounting Bracket Assembly1. Wrap LED data cable once around ferrite bead and close bead, as in illustration.
2. Plug power cable and data cable into respective ports in LED display.
3. Fasten LED display to LED Mounting Bracket with four Torx screws. Let cables hang free.
4. Route cables beneath Mounting Bracket. Use three tie wraps to fasten each cable to Mounting Bracket 
through holes in Bracket.
5. Remove backing and place adhesive side of adhesive footing on bottom of Mounting Bracket.
6. While facing rear of Top Cover Assembly, hold Mounting Bracket/LED/Cables assembly above Top 
Cover so LED display faces forward.
7. Pivot front of Mounting 
Bracket up and hook four 
rear tabs into top four vent 
holes on Top Cover. Route 
data cable between first and 
second tab. Route power 
cable between third and 
fourth tab.
8. Carefully pivot Mounting 
Bracket down until felt pads 
rest on top cover.
9. Slide clips through clip 
holes at front of Mounting 
Bracket. Slotted sides face 
up. Clips grab both Top 
Cover and Mounting 
Bracket.
10. Pry up slotted sides and 
push clips forward to clear 
posts on Mounting Bracket. 
Let clips close over posts. 
Avoid damaging rubber seal 
and tape on Top Cover 
Assembly when installing.
11. Secure clips over posts with 
nylon nuts.
12. Tighten four tamper-proof 
screws on rear of Mounting 
Bracket to fasten it tight to 
cabinet.
LED DISPLAY
LED MOUNTING BRACKET TOP COVER ASSEMBLY LED DATA CABLELED POWER CABLE
TYE WRAP (4)
ESNA NUTMOUNTING CLIP
REAR TAB
POST
LED ASSEMBLY
FERRITE BEADADHESIVE
FOOTING(4 PLACES
ON BOTTOM)
NLX RISER BOARD
DOLPHIN BOARD “SER_PORT” “FAN”CONNECTIONS TO ELECTRONICS BOARD
SPACER
LARGE HOLE
INTERNAL
SERIAL CABLEDB9 TO RJ25
ADAPTER SERIAL PORT
SERIAL BRACKET MOUNTING
MOUNTING BRACKET