Midway Skins Game Conversion Kit Operations Service Manual

Setup - 8Midway Games West Inc.
INSTALL GAME ELECTRONICS
WARNING: DISCONNECT POWER. 
To avoid electrical shock, turn off power switch and
disconnect AC line cord before removing or replacing any component. After servicing
components, be sure all ground wires are secure before restoring power.
1. REMOVE OLD ELECTRONICS  
Label, then carefully disconnect cables on each printed electronics board
assembly in cabinet. Note orientation of JAMMA edge connector on CPU Board Assembly. Remove boards and
store in...

Skins Game Conversion KitSetup - 9
WIRE CABINET
CAUTION: ATTACH CONNECTORS PROPERLY.
 Be sure that printed circuit board
(PCB) connectors mate properly. If connectors do not slip on easily, do not force them. A
reversed connector may damage video game machine and void warranty. Connector
keys only allow a connector to fit one set of pins on a board.
CAUTION: OBSERVE GROUNDING.  
Be aware of ground wires in game. Ground wires
are usually green or green with a yellow stripe. Reuse any existing ground...

Setup - 10Midway Games West Inc.
POWER UP AND TEST GAME
1. Plug line cord into AC power source and turn on power switch. LEDs in electronics cage should illuminate.
Using the 20-volt DC setting on a digital voltmeter, measure DC voltages at the power connector pins. Adjust
the +5V source if it is necessary. Voltage tolerances are ±.4 on +5V, ±½ V on +12Vhe game begins self
diagnostics. If no errors are found, Attract Mode begins. If problems occur, check wiring and refer to Trou-
bleshooting Chapter.
2....

CHAPTER


SERVICE
NOTICE: Instructions in this chapter apply to a typical converted Midway upright cabinet. 

Service - 2Midway Games West Inc.
SERVICE
CAUTION:
 Before attempting any of the following procedures on your Skins Game Video
Game Machine, turn AC Power off. Failure to do so can cause personal injury, may
damage the components, and may void your warrantee.
Control Panel
To remove controls, unlock and
open control panel. Remove
washers, nuts, and other fastening
software before removing
components. Disconnect and label
wiring for easier reassembly.
Remove plastic overlay if necessary.
Joystick...

Skins Game Conversion Kit Service - 3Push Buttons
Open control panel. Label and
disconnect wires. Separate switch
from its pushbutton. Bend large
prong away from switch just enough
to slide switch off housing.
To remove light inside START
button, pull light bulb up and out of
socket. Unscrew switch mounting
nut and pull entire pushbutton out
from front of panel.
Fan Assembly
Remove rear door. Remove hex
nuts on groundplane cover.
Remove cover and set in safe
place. Disconnect wiring harness
and remove...

Service - 4Midway Games West Inc.
NOTES:
____________________________________________________________________________________
____________________________________________________________________________________
____________________________________________________________________________________
____________________________________________________________________________________
____________________________________________________________________________________...

CHAPTER


SYSTEM SOFTWARE
NOTICE: This manual is subject to change without notice. Midway Games W est Inc. reserves
the right to make improvements in equipment function, design, or components as progress in
engineering or manufacturing methods may warrant. 

System - 2Midway Games West Inc.
GAME OPERATION
PLAYER CONTROLS
OPERATOR CONTROLS
SERVICE
CREDI T VOL.
DOWN UP VOL.
MODETEST
TYPICAL TEST SWITCH BRACKET PUSHBUTTON LOCATIONS
Keypad Pod
Assembly
Lets players enter their
PINs as well as allow
operators to navigate
the system menus.
Joystick Assembly
Pulling back on the joystick winds your club backwards.
Pulling to the left aims the swing a bit to the right;
pulling to the right aims the swing a bit to the left.
The joystick assembly is designed to...

Skins Game Conversion Kit System - 3  
Menu System
Follow instructions at the bottom of each menu screen to access more menus and change settings. The
current date and time are shown.
ATLANTIS TESTS
Day Date Year Time
ADJUST VOLUME
STATISTICS
GAME OPTIONS
COIN OPTIONS
TOURNAMENT OPTIONS
SET DATE/TIME
TESTS
EXIT TO GAME
To select test, use +/-/LEFT/RIGHT
To run test, Press START or TEST
EPROM: X.XX Sept 7 1999 XX:XX:XX
GUTS: X.XX Aug 30 1999 XX:XX:XX
Game: Sep 2 1999 XX:XX:XX
Serial #: XXXXXXX
ADJUST...