Midland 1001z Transceiver Owners Manual

							2     
Table of Contents
How to install your Midland mobile CB.................................. 3
Installation and operating accessories furnished with your Midland
CB: ................................................................................................... 3
Where to locate your CB transceiver. ............................................... 3
Mechanical mounting. ...................................................................... 4
Power wiring (negative ground only). ............................................... 4
Installation of microphone hanger. ................................................... 5
Antenna: ................................................................................... 6
How to select, position install and tune the right one for you. .......... 6
Antenna installation. ......................................................................... 7
Tuning your antenna. ....................................................................... 7
Factors affecting CB range ..................................................... 7
Noise: ........................................................................................ 7
Midland MODEL 1001Z CB Operating controls ..................... 8
FRONT PANEL CONTROLS .................................................... 8
BACK PANEL ......................................................................... 10
HOW TO OPERATE YOUR TRANSCEIVER .......................... 10
TECHNICAL SPECIFICATIONS ............................................. 10
GENERAL ...................................................................................... 10
TRANSMITTER .............................................................................. 11
SERVICE................................................................................. 11
LIMITED WARRANTY. ..................Error! Bookmark not defined.
Midland MODEL 1001Z 40 Channel mobile citizens band
transceiver
For your protection, the space below is provided for you to record the Serial
Number of this product, which is located on the rear of the radio. After
recording this number, keep this record for future reference along with the
sales receipt. The sales receipt is needed should your radio ever need
service.
FCC I.D.   MMA1001
Serial Number:____________________ 
						

							3
Welcome to the world
of  Midland electronics
Congratulations on your purchase of a state-of-the-art mobile CB radio. In
the years ahead, you can expect to realize time and again why Midland holds
the front running position among CB users everywhere. You will come to
know that Midland power is more than just a slogan, but the heading of long
list of hearable, seeable benefits. As your Midland CB experience unfolds
and grows we hope you will remember that CB is only one kind of electronic
excellence available under the Midland name.
Your 40 channel CB represents the state of the art in high tech engineering.
The unit incorporates microprocessor controlled PLL circuitry for precise
tuning.
How to install your Midland mobile CB
This transceiver may be installed in any 12-volt negative ground-
system car or truck.  Most current U.S. and foreign vehicles use a negative
system, but some older models and some newer large trucks may have a
positive ground.
Check the requirements for your vehicle before you begin
installation.
Generally, you have a negative-ground system if the minus ( - )
battery terminal is connected to the motor block.  Contact your dealer in the
event you are unable to determine your vehicle’s polarity system.
Installation and operating accessories furnished with your
Midland CB:
1.  Easy removal mounting bracket system.
2.  Microphone bracket system.
3.  All main-unit and microphone mounting hardware needed for normal     
     installation.
4.  Plug-in microphone with coil cord.
5.  FCC part 95, Subpart D.
6.  Owner’s Manual.
Where to locate your CB transceiver.
Your new Midland CB is designed to be installed under the dash or
vertically on a console of your vehicle. 
						

							4
Safety and convenience are the primary considerations in deciding
exactly where to locate your radio.
Caution:  Be sure that the unit is located so that it does not interfere with the
driver, supplemental restraint systems (air bags) or impair access to any
controls.  Connecting cables must be routed and secured in such a manner
as not to interfere with the operation of the brake, accelerator or other
controls. Interference from either the unit or connecting cables may
contribute to the loss of control of the vehicle.
Mechanical mounting.
Step 1: Heeding the caution, use the mounting bracket as a template for
marking the location of screw holes under the dash.  Use an awl, nail or
other sharp pointed object to mark the hole locations.
Step 2:  Drill a 1/8” hole for each screw hole in the mounting bracket. Attach
the bracket to the dash with the Phillips head sheet metal screws provided.
, Extreme care should be exercised when drilling into the dash to avoid damage to
under-dash electronic ignition, cruise control, instrument and / or accessory
wiring.
Step 3: Position the main unit between the bracket arms in line with the
retention knobs.  Set the angle for optimum operating comfort and
accessibility.
Step 4: Tighten the retention knobs
Power wiring (negative ground only).
Step 1:  If you have not determined whether your vehicle has a negative or
positive ground, do so now. Then disconnect the negative lead from the
battery to prevent short circuits that can occur during wiring. Do not connect
this transceiver to positive ground electrical systems.
Step 2:  With negative ground
A. Connect the positive (RED WIRE) the one with in-line fuse holder to either
the (a) fuse block, (b) cigarette lighter, or (c) directly to the positive post on
your battery. 
						

							5
Usually, the fuse block is the most convenient connecting point. It is also
possible to connect to the Accessory terminal on the fuse block or ignition
switch, so that your CB automatically goes off when the ignition goes off.
B. Tightly connect the ground (BLACK WIRE) directly to the vehicle’s metal
frame. A good direct metal-to-metal ground is essential for optimum
performance.
, Installations using the cigarette lighter socket for power require an extra ground
wire from the radio chassis to the vehicle if the radio is not fastened to a
grounded part of the vehicle.
Installation of microphone hanger.
Mounting holes are provided on the microphone hanger bracket. The bracket
can be attached to the vehicle dash, the holes provided on the left side of the
radio, or other convenient location. 
						

							6
Antenna:
How to select, position install and tune the right one for you.
Basically, you may choose from two types of mobile CB antennas -
full-length whip and loaded whip - and a variety of mounts (depending on
where you locate your antenna). 
Midland markets a broad line of high-performance antennas. The dealer who
sold you your Midland CB can advise which type is best for you.
Where you locate your antenna does make a difference.
Some general rules for antenna location that can aid CB performance:
1.  Put your mount as high on the vehicle as possible.
The higher the proportion of antenna length that is above the roof, the better.
2.  If possible, mount the antenna in the center of whatever surface you
choose.
3.  Keep antenna cables away from noise sources, such as the ignition
system, gauges, etc.
4.  Make sure you have a solid metal-to-metal ground.
5.  Exercise care to prevent cable damage.
Essentially, you have five location choices: the roof, gutter, rear deck, front
cowl or rear bumper.  Where you decide to locate your antenna will
determine the type of antenna you install.  Again consult your Midland CB
dealer for advice and guidance, and measure your needs against the
attributes of the various Midland antenna models he carries. 
						

							7
Antenna installation.
Follow the manufacturer’s installation instructions carefully.
, Warning:  Never operate your CB radio without attaching an antenna or with a
broken antenna cable.  This will result in damage to transmitter circuitry.
, Safety notice:   The antenna used for this radio must be installed to provide a
separation distance of at least 20cm (8 in.) from all persons and must not be co-
located or operating in conjunction with any other antenna or transmitter.
Tuning your antenna.
Some antennas are factory tuned.  However, performance can usually be
improved by slightly lengthening or shortening the antenna using a Standing
Wave Radio (SWR) meter.  For the exact procedures to be used, refer to the
antenna manufacturer’s installation manual.
You can buy an SWR meter separately or have your antenna checked by
your Midland CB Dealer’s service department.
Factors affecting CB range
Essentially, they are the same influences that optimize or limit AM and FM
broadcast signals.
Terrain: Hills, valleys and buildings naturally interrupt and shorten CB
signals. In short, anything that is between you and the person you want to
talk to can shorten your CB range. You can expect to maintain maximum
transmitting/receiving performance in flat, open country.
Weather: You can expect that CB range will be reduced – perhaps
drastically – in times of atmospheric disturbance, such as in a thunderstorm
or heavy snow. Sunspots too are known to adversely affect CB performance.
Noise:
A common source of excessive noise is the ignition system. In many vehicles
today the electric fuel pump is another possible source of noise. If you
suspect this is true, turn off the ignition. With the CB in receive mode the
noise is no longer present this is a source of the noise. In some cases the
noise can be reduced or eliminated by making sure the CB radio chassis is
grounded. This is in addition to the power cord. In extreme cases, additional
grounding of components may be necessary. 
						

							8
Midland MODEL 1001Z CB Operating controls
FRONT PANEL CONTROLS
 ON/OFF VOLUME: In the off position your transceiver power is off. Turn 
    this control clockwise to switch on the unit and adjust the volume.
 SQUELCH CONTROL: Adjust this control until background noise just  
    disappears. If the control is adjusted too far clockwise it may cause  
    muting of weaker signals.
S/RF POWER METER: This display is used in receiving to indicate the
relative signal strength of incoming signals.  When transmitting, it shows RF
power output.
PA/CB Switch: When in PA mode, it causes your voice to operate the
optional external PA speaker.  In CB mode, the microphone operates the
transmitter.
MICROPHONE CONNECTOR: Plug in the supplied microphone to this 
    connector.   Received signals will not be heard without the microphone.
CHANNEL KNOB: This easy-to-operate control allows changing of CB
channels, either up or down. 
CHANNEL INDICATOR: The LED displays the channel number.
 TX LED: indicator for showing the unit is transmitting. 
						

							9
 Push-To-Talk bar: Press this bar to cause the radio to transmit. Hold the
microphone about 2 inches from your mouth and speak in a normal voice. 
						

							10
BACK PANEL
ANTENNA CONNECTOR: Connect a standard 50-ohm CB antenna to this 
        connector.
EXT SP: When a speaker is connected to this jack, the internal speaker 
is by-passed. All received signals will be heard through the
external speaker. The speaker connected to the “EXT” jack
should be rated at 8 ohms and 5 watts.
PA JACK: An optional PA speaker may be attached to your transceiver
through the PA output jack on the back panel.  This allows you to
communicate with pedestrians or other vehicles through your CB
microphone. The speaker connected to the “PA” jack should be rated at 8
ohms and 5 watts.
DC 13.8V POWER Cord: Connects to power cord with in line 2 Amp fuse.
HOW TO OPERATE YOUR TRANSCEIVER
You should become familiar with the controls and complete the preceding
installation instructions before attempting to operate your CB.
1. Rotate the on/off volume control clockwise to turn the unit on.
2. Adjust the squelch control fully counter-clockwise so noise is heard.
3. Adjust the volume for a normal listening level.
4. Rotate the squelch control until the noise just disappears.  
5. Select the desired channel by rotating the channel selector. 
6. To transmit, press the PTT bar on the side of the microphone. Hold the
microphone 2 to 3 inches from your lips and speak in a normal voice.
7. To receive, simply release the PTT bar.
Warning: Do not attempt to make any internal adjustments.  Internal adjustments and/or
modifications can lead to illegal operation as defined by the FCC rules and regulations, Part 95.
They must be made only by qualified technical personnel.  Illegal operation can lead to serious
consequences.
TECHNICAL SPECIFICATIONS
GENERAL
Frequency range ..........................................................................26.965-27.405 MHzChannels ..............................................................................................................40Modulation type ...................................................................................................AMAntenna impedance .......................................................................................50 OhmLoudspeaker ...................................................................................................8 Ohm