Home > Marantz > Projector > Marantz Vp4001 DLP Projector User Manual

Marantz Vp4001 DLP Projector User Manual

Here you can view all the pages of manual Marantz Vp4001 DLP Projector User Manual. The Marantz manuals for Projector are available online for free. You can easily download all the documents as PDF.

Page 31

30
The height of the projector can be ad-
justed using the adjustment feet at the
front and rear of the projector.
When the screen is above the projec-
tor, the projection image can be made
higher by adjusting the projector.
1
2
Remove your hands from the
HEIGHT ADJUST lever of the pro-
jector after its height has been
finely adjusted.
•The angle of projection is adjustable up
to 8 degrees from the surface on which
the projector is placed.
Lift the projector to adjust its
height while lifting the HEIGHT...

Page 32

Basic
Operation
31
3
•Do not apply too much pressure on the pro-
jector when the front adjustment foot comes
out.
•When lowering the projector, be careful not to
get your fingers caught in the area between
the adjustment foot and the projector.
•Hold the projector firmly while lifting or carry-
ing.
•Do not hold by the lens area.
Use the rear adjustment foot to
make the projector level.
•The projector is adjustable ±1 degree
from the standard position.
Info
Rear adjustment foot
•When adjusting the height...

Page 33

32
Correcting Trapezoidal
DistortionAdjustment buttons
(P/R/O/Q) KEYSTONE
button
When the image is projected either from
the top or from the bottom towards the
screen at an angle, the image becomes
distorted trapezoidally. The function for
correcting trapezoidal distortion is
called Keystone Correction.
There are the two types of the Keystone
Correction.
1) The “GEOMETRIC  ADJUSTMENT”
method corrects trapezoidal distor-
tion by specifying 4 marks on the
screen.
2) The “H & V KEYSTONE” method fea-
tures...

Page 34

Basic
Operation
33
Selecting the Type of
Correction
GEOMETRIC
ADJUSTMENTFor correcting an image by
designating the corner of the
projected image.
(See page 34.)
H & V
KEYSTONEFor correcting an image by
designating the horizontal or
vertical axes. (See page 35.)
Press c KEYSTONE on the remote control.
•“GEOMETRIC ADJUSTMENT” will be
displayed.
•Each time c KEYSTONE is pressed, the
display toggles as follows: Select the Keystone correction method.
GEOMETRIC
ADJUSTMENTH & V KEYSTONE
The display disappears....

Page 35

34
Image Projection (Continued)
ROn-screen display
GEOMETRIC ADJUSTMENT
Geometric Adjustment
2
Press c KEYSTONE on the remote
control repeatedly until “GEOMET-
RIC ADJUSTMENT” is displayed.
3Press P, R, O or Q to move the po-
sition for the upper left of the im-
age.
•Adjust the screen until the displayed red
arrows line up in the upper left.
4Press i ENTER to set the position.•The arrow in the upper right turns red.
5Repeat the same procedure with
the positions for the upper right,
lower right and lower...

Page 36

Basic
Operation
35
2Press c KEYSTONE on the remote
control repeatedly until “H & V
KEYSTONE” is displayed.
•When the “GEOMETRIC ADJUSTMENT”
mode has been used to adjust the im-
age, a confirmation screen displays be-
fore the “H & V KEYSTONE” screen, ask-
ing if you want to reset the adjustments
or not. Then select RESET.
H & V KEYSTONE
H&V KEYSTONE
END
ENTERADJUST
RESET
ROn-screen display
1Project the image and adjust the
focus, image size, and projection
angle.
Horizontal Keystone Correction...

Page 37

36
ASPEC
TEN
TER INPUT
MENU
I
NPUTS
T
A
N
D
B
Y
/
O
NL
A
M
PT
E
M
P
.ASPECTENTERINPUT
MENU
INPUT
STANDBY/ONLAMPTEMP.
Image Projection (Continued)
Aspect Mode
This function allows you to modify or customize the Aspect mode to enhance the input image. De-
pending on the input signal, you can choose “FULL”, “NORMAL”, “ZOOM” or “THROUGH (Computer
input only)”  image.
Press ASPECT on the projector or A ASPECT on the remote control.
ASPECT buttonA
R/C
SYNC
RETURN ENTER
AUTO SYNC ASPECT
IMAGE SHIFT RGB/COMP....

Page 38

Basic
Operation
37
: Cutout area on which images cannot be projected.
Computer
Input Signal
FULLOutput screen image
ComputerImage
typeNORMAL
1280 × 720 Resolution lower than
XGA
XGA
(1024 × 768)
4:3 aspect
ratio
16:9 aspect
ratio
ZOOM TROUGH
4:3 aspect
ratio
About Copyrights
•When using the ASPECT function to select an image size with a different aspect ratio
to a TV program or video image, the image will look different from its original appear-
ance. Keep this in mind while choosing an image size.
•The...

Page 39

38
Operating with the Remote Control
Freezing a Moving Image
Press hFREEZE.• The projected image is frozen.
Press hFREEZE again to return to
the moving image from the cur-
rently connected device.
1
2
Shifting the Projected Im-
age Vertically (Image Shift)
Press PIMAGE SHIFT.• The image moves up.
Press RIMAGE SHIFT.• The image moves down.
For easier viewing, this function shifts
the entire image projected on the
screen up or down when projecting 16:9
images from DVD players or other con-
nected devices....

Page 40

Useful
Features
39
The following shows the items that can be set in the projector.
The selectable items vary depending on the selected input, input signals, or adjustment
values. Items that cannot be selected will be greyed out.
Menu Items
“C.M.S.”
PAGE 2
“Picture” menu
Picture Mode
K 7500
1
CLR TempBrilliantColor™
C. M. S.
Progressive
3D Progressive
DNR
Level 1
IRIS
WIDE Picture Comp. 1
SEL./ADJ.
RETURNSingle ADJ
END Reset
Standard
Lamp Setting
Normal
C. M. S. - Hue
0
0
0
0C. M. S. - SaturationC. M. S....
Start reading Marantz Vp4001 DLP Projector User Manual

Related Manuals for Marantz Vp4001 DLP Projector User Manual

All Marantz manuals