Marantz Vp 8100 DLP Projector User Manual

7
ENGLISH
INTRODUCTION
1.Open the cover.
2.Insert batteries (AA).
Make sure to match the + and – marks on the batteries
with  inside the battery component.
3.Close the cover.
CAUTION
– Do not mix old and new batteries, and never mix different
types of batteries (standard, alkaline and so on).
– If the user does not intend to use the Remote Controller for
a long time, remove the batteries.
– Do not be subjected to strong shock.
– Do not be subjected to moisture.
If moisture gets the unit, wipe it off...

8
SET UP PROCEDURES
ENGLISH
Adjust the vertical and
horizontal position of the
projector.
Side view
U
D LRA TEXAS INSTRUMENTS TECHNOLOGYM
E
N
UENTERINPUTS
T
A
N
D
B
YW
A
R
N
I
N
GPOWER
Top view
INSTALLATION
Floor Installation
Ceiling Installation
For ceiling installation, consult with Marantz dealer.
CAUTION
– Do not look into the lens when the projector is turned on.
It could damage your eyesight.
Vertical positioning
Horizontal positioning Horizontal center of the screen
Height
Projecting
distance...

9
ENGLISH
SET UP PROCEDURES
EXT. INT. OUT
TRIG.2
REMOTE CONTROL TRIG.1 RGB IN YPB/CB
COMPONENT  VIDEO  IN S-VIDEO
IN
VIDEO  IN
PR/CR
IN
40
60
80
100
120
150
200
240
275
(300 for 4:3 screen)1730
(681/8)
2620
(103
1/8)
3510
(138
1/4)
4400
(173
1/4)
5290
(208
1/4)
6620
(260
5/8)
8850
(348
3/8)
10630
(418
1/2)
12180
(479
1/2)2080
(81
7/8)
3150
(124)
4220
(166
1/8)
5300
(208
5/8)
6360
(250
3/8)
7960
(313
3/8)
10630
(418
1/2)
12760
(502
3/8)
–212
(8
3/8)
318
(12
1/2)
425
(17
1/4)
531
(20
7/8)
639
(25
1/8)
796...

10
SET UP PROCEDURES
ENGLISH
• Press the 4:3 key or the ZOOM key on the remote controller for the 4:3 aspect ratio video source.
• Press the FULL key on the remote controller for 16:9 aspect ratio video source.
• Press the FULL key on the remote controller for both 4:3 and 16:9 aspect ratio video sources.
• Video sources will be projected according to its aspect ratio as illustrated below.
N
4:3 mode N
ZOOM mode
N
FULL modeN
FULL mode
4:3 video source4:3 video source
N
SQUEEZE mode
4:3 video source
N...

11
ENGLISH
SET UP PROCEDURES
EXT. INT. OUT
TRIG.2
REMOTE CONTROL TRIG.1 RGB IN YPB/CB
COMPONENT  VIDEO  IN S-VIDEO
IN
VIDEO  IN
PR/CR
IN
DVD
VCR
S-VIDEO OUT
VIDEO OUT
COMPONENT VIDEO OUT
EXT. INT. OUT
TRIG.2
REMOTE CONTROL TRIG.1 RGB IN YPB/CB
COMPONENT  VIDEO  IN S-VIDEO
IN
VIDEO  IN
PR/CR
IN
Computers
to an analog RGB OUT
When making connections be sure to:
• Turn off all equipment before making any connections.
• Use the proper cables for each connection.
• Insert the plug for the cables properly,...

12
SET UP PROCEDURES
ENGLISH
1.Connect the supplied AC power cord.
The STANDBY indicator will light in green and the
projector goes into the standby mode.
2.Press the POWER ON key on the remote controller or the
POWER key on the projector.
The POWER key lights in green.
3.Switch on the equipment connected to the projector. Press
the INPUT SELECT key on the projector or the
COMPONENT key, S-VIDEO key, VIDEO key, or RGB key
on the remote controller.
4.Press the OSD key twice on the remote controller to...

13
ENGLISH
OPERATIONS
Refer to the on-screen menu for making various adjustments
and settings.
1.Press the MENU key.
The menu display appears.
2.Use the M/Nkeys to select a menu, then press the
ENTER key.
The selected menu appears.
3.Make adjustments in MEMORY SELECT, PICTURE
ADJUST, or SETTING.
To display the previous menu Press the MENU key.
5)&5&3y
.&.03:y4&-&$5
1*$563&y%+645
4&55*/(
The user can adjust the picture to suit own preference by using
the PICTURE ADJUST feature.
1.Use the O/Pkeys to...

14
OPERATIONS
ENGLISH
– 2-3 P/D
Select either auto or off from the 2-3 P/D system.
– COMPONENT
When set to AUTO, a video system is automatically selected as
either NTSC, 480p, 720p, or 1080i. When AUTO does not work
out, select an appropriate system from either NTSC, 480p,
720p, or 1080i.
– ALL RESET
When the user selects “YES”, the following message appears:
Again, select “YES”, and press the ENTER key. Then restore
the factory default settings except for the lamp life and RGB
ADJUST MEMORY.
– RESET...

15
ENGLISH
LAMP LIFE
The user can display the remaining lamp life at any time by
pressing the OSD key on the remote controller. LAMP LIFE is
displayed at the very bottom of the menu.
Notes:
• When the LAMP LIFE becomes less than 1000 HOURS, it is
recomended to replace the lamp unit. A lamp may be worn
out when the LAMP LIFE becomes less than 1000 HOURS.
• The projector is designed not to turn on after the lamp use
has exceeded 2000 hours. (LAMP LIFE 0 HOUR)
If the projector is in use, it will turn off.
P...

16
ADDITIONAL INFORMATION
ENGLISH
CAUTION:
• Do not touch the lamp and the lamp unit. It will be extremely
hot. Allow at least one hour for the lamp to cool down before
handling.
• Do not loosen any screws except for those mentioned below.
• The lamp may break if handled improperly.
• Do not use a lamp housing other than a Marantz
replacement lamp unit.
WARNING:
• The lamp itself may get hot. Be careful when handling.
1.Press the POWER key to turn the projector off.
2.Unplug the AC power cord.
3.Wait at...