Marantz Projector Vp 11s1 User Manual

							13
ENGLISH
❖
Mounting on the ceilingCAUTION–For ceiling installation, consult with Marantz authorized dealer.
–Do not look into the lens when the projector is turned on.  It could damage your eyesight.
INSTALLATION
❖
Installing on a tabletopRecommended Setting
Screen
Screen size (vertical)
Screen upper end
Range from light axis to upper end
Light axis (center)Height from installing
level to light axis
Screen lower end
Projection distance
lens head
Lens shift range
Screen
Screen upper end
Range from light axis to upper
end
Light axis (center)
Height from installing level to light axis
Installing level
Screen size (vertical)
Screen lower end
Projection distance
lens head
Lens shift range
7146@@&/(
 
 
 
 
 1.
 
 
						

							14
ENGLISH
❖
16 : 9 Screen
In case of displaying the 16:9
picture on the whole of the
16:9 screen.❖
4 : 3 Screen
In case of displaying the 16:9
picture on the whole of the 4:3
screen.
VP-12S1
Screen Size and Projection Distance (inch)  VP-11S1
Diagonal Width Height Minimum Maximum
inch inch inch inch inch
61
62 12/16
69 12/16
71  8/16
73  3/16
78  7/16
80  3/16
87  3/16
92  6/16
95 14/16
104  9/16
107  3/16
115 15/16
117 11/16
130 12/16
148  3/16
174  5/16
217 14/1634  5/16
35  5/16
39  4/16
40  3/16
41  3/16
44  2/16
45  2/16
49
51 15/16
53 15/16
58 13/16
60  5/16
65  3/16
66  3/16
73  9/16
83  6/16
98  1/16
122  9/1688  6/16
90 15/16
101  5/16
103 14/16
106  7/16
114  3/16
116 13/16
127  2/16
134 14/16
140  1/16
153
156 14/16
169 12/16
172  6/16
191 12/16
217  9/16
256  6/16
321129  1/16
132 13/16
147 13/16
151  9/16
155  5/16
166  8/16
170  4/16
185  4/16
196  7/16
203 15/16
222 11/16
228  4/16
247
250 12/16
278 13/16
316  4/16
372  6/16
465 15/16 70
72
80
82
84
90
92
100
106
110
120
123
133
135
150
170
200
250
To calculate the installation measurement (unit : inch)
Minimum = 1 5/16 x Screen Size - 2 2/16 
Maximum= 1 14/16 x Screen Size - 1 15/16
Note : 
When installing the projector, consider ±5% tolerance for the Projection Distance in the above table.16:9 Screen Size (1.77:1 Aspect Ratio) Projection Distance
Screen size
(Diagonal)
Projection distance
Screen
Diagonal Width Height Minimum Maximum
inch inch inch inch inch
70
72
80
82
84
90
92
100
106
110
120
123
133
135
150
170
200
25056
57 10/16
64
65 10/16
67  3/16
72
73 10/16
80
84 13/16
88
96
98  6/16
106  6/16
108
120
136
160
20042
43  3/16
48
49  3/16
50  6/16
54
55  3/16
60
63 10/16
66
72
73 13/16
79 13/16
81
90
102
120
150108  8/16
111 10/16
124  5/16
127  7/16
130 10/16
140  1/16
143  4/16
155 14/16
165  6/16
171 11/16
187  8/16
192  4/16
208
211  3/16
234 14/16
266  8/16
313 14/16
392 14/16158  5/16
162 14/16
181  3/16
185 13/16
190  6/16
204  2/16
208 11/16
227
240 12/16
249 14/16
272 12/16
279 10/16
302  9/16
307  2/16
341  7/16
387  4/16
455 14/16
570  6/16
To calculate the installation measurement (unit : inch)
Minimum = 1 9/16 x Screen Size - 2 2/16 
Maximum= 2 5/16 x Screen Size - 1 15/16 
Note : 
When installing the projector, consider ±5% tolerance for the Projection Distance in the above table.4:3 Screen Size (1.33:1 Aspect Ratio) Projection Distance
❖
16 : 9 Screen
In case of displaying the 16:9
picture on the whole of the
16:9 screen.❖
4 : 3 Screen
In case of displaying the 16:9
picture on the whole of the 4:3
screen.
VP-12S1
Screen Size and Projection Distance (mm)  VP-11S1
Diagonal Width Height Minimum Maximum
inch mm mm mm mm
70
72
80
82
84
90
92
100
106
110
120
123
133
135
150
170
200
250
To calculate the installation measurement (unit : mm)
Minimum = 32.8 x Screen Size - 53.4
Maximum= 47.5 x Screen Size - 48.8
Note : 
When installing the projector, consider ±5% tolerance for the Projection Distance in the above table.16:9 Screen Size (1.77:1 Aspect Ratio) Projection Distance
1,550 
1,594 
1,771 
1,815 
1,860 
1,992 
2,037 
2,214 
2,347 
2,435 
2,657 
2,723 
2,944 
2,989 
3,321 
3,763 
4,428 
5,535 872 
897 
996 
1,021 
1,046 
1,121 
1,146 
1,245 
1,320 
1,370 
1,494 
1,532 
1,656 
1,681 
1,868 
2,117 
2,491 
3,113 2,243 
2,308 
2,571 
2,636 
2,702 
2,899 
2,964 
3,227 
3,423 
3,555 
3,883 
3,981 
4,309 
4,375 
4,867 
5,523 
6,507 
8,147 3,276 
3,371 
3,751 
3,846 
3,941 
4,226 
4,321 
4,701 
4,986 
5,176 
5,651 
5,794 
6,269 
6,364 
7,076 
8,026 
9,451 
11,826 
Diagonal Width Height Minimum Maximum
inch mm mm mm mm
70
72
80
82
84
90
92
100
106
110
120
123
133
135
150
170
200
250
To calculate the installation measurement (unit : mm)
Minimum = 40.1 x Screen Size - 53.4  
Maximum= 58.1 x Screen Size  - 48.8
Note : 
When installing the projector, consider ±5% tolerance for the Projection Distance in the above table.4:3 Screen Size (1.33:1 Aspect Ratio) Projection Distance
1,422 
1,463 
1,626 
1,666 
1,707 
1,829 
1,869 
2,032 
2,154 
2,235 
2,438 
2,499 
2,703 
2,743 
3,048 
3,454 
4,064 
5,080 1,067 
1,097 
1,219 
1,250 
1,280 
1,372 
1,402 
1,524 
1,615 
1,676 
1,829 
1,875 
2,027 
2,057 
2,286 
2,591 
3,048 
3,810 2,754 
2,834 
3,155 
3,235 
3,315 
3,556 
3,636 
3,957 
4,197 
4,358 
4,759 
4,879 
5,280 
5,360 
5,962 
6,764 
7,967 
9,972 4,018 
4,134 
4,599 
4,715 
4,832 
5,180 
5,296 
5,761 
6,110 
6,342 
6,923 
7,098 
7,679 
7,795 
8,666 
9,828 
11,571 
14,476 
Screen size
(Diagonal)
Projection distance
Screen
Width
Height
: Image size = Screen sizeWidth
Height
: Image size = Screen size
Width
Height
: Image size
: Screen sizeWidth
Height
: Image size
: Screen size
7146@@&/(
 
 
 
 
 1.
 
 
						

							15
ENGLISH
Screen PositionScreen Position
0% (Center)
0% (Center) (+100%)
-85%
Screen Height = 1H0.3H Up 
More
0.5H 
Up
0.4H 
Down+165%
+100%
Focus pattern color: White 
Focus pattern color: Green
VP-11S1 VP-11S1
❖
Standard condition (From -85% to +100%)
❖
Extended mounting condition (From +100% to +165%)
Lens shift position
CAUTION:
In the expanded mounting condition (green focus pattern), the corners of the picture may appear
dark or distorted.
7146@@&/(
 
 
 
 
 1.
 
 
						

							16
ENGLISH
BASIC OPERATIONS
Press the ONbutton on the remote controller or the / Ibutton on the projector.
The ON indicator lights up.
Switch to the equipment connected to the projector.
Every time the INPUTbutton of the projector or the INPUT3button of the remote controller is pressed,
the input signal rotates in the order of COMPONENT 1 
➔COMPONENT 2 
➔S-VIDEO 
➔VIDEO 
➔RGB
➔HDMI 1 
➔HDMI 2. When the INPUT4button of the remote controller is pressed, the input signal
rotates in the opposite order. An input signal can also be directly selected by pressing one of the COMP.1,
COMP.2, S-VIDEO, VIDEO, RGB, HDMI 1and HDMI 2buttons on the remote control.
INPUT V-MUTE
ENTERMENU
ASPECTINFO.
C1 C2 S G1
H1 H2 V G2A1
A2 RGB G3
STD DYN
I M
AG4
THTRCOMP.1 COMP.2 S-VIDEO USER
HDMI 1 HDMI 2 VIDEO
AUX 1
BLANKING AUX 2IRIS LAMP
C.TEMP GAMMA
B1
OFF
B3
B2
Selecting the Input Signal Source
C1 C2 S G1
H1 H2 V G2A1
A2 RGB G3
STD DYN G4
THTRCOMP.1 COMP.2 S-VIDEO USER
HDMI 1 HDMI 2 VIDEO
AUX 1 AUX 2
ON
STANDBYIRIS LAMP
C.TEMP GAMMA
Turning on the Power
You can select 4 kinds of ASPECT mode using remote controller.
Pressing the ASPECTbutton on the remote control rotates the
aspect ratio in the order of FULL 
➔NORMAL 
➔ZOOM 
➔V-
STRETCH 
➔THROUGH, allowing you to select an aspect ratio.
An aspect ratio can also be directly selected by pressing one of
the FULL, NORMAL, ZOOMor THROUGHbuttons on the remote
controller. A selection can also be made from the menu. (

P.23)Selecting the Aspect Mode
INPUT V-MUTE
ENTERMENU
ASPECT
FULL CINEMA
VCR MODE
BLACK LEVEL
PATTERN
BLACK
NOR ZOOM THRUINFO.
I M
A
BLANKING
B1
OFF
B3
B2
7146@@&/(
 
 
 
 
 1.
 
 
						

							17
ENGLISH
•Press the  ZOOMbutton, the  NORMALbutton or the  FULLbutton on the remote controller for the 4:3
aspect ratio video source.
• Press the  FULLbutton on the remote controller for 16:9 aspect ratio video source, such\
 as 1080i,
1035i, and 720p video systems.
• Press the  FULLbutton on the remote controller for the squeezed video source.The Screen Images in a 16:9 screen❖
Original Source Image
❖
Full mode
The 16:9 squeezed image is displayed with the
correct aspect.❖
Normal mode
❖
Zoom mode
16 : 9  video source
The 4:3 image is enlarged horizontally.
The picture in normal ratio 4:3 is displayed.The picture in normal ratio 4:3 is enlarged vertically
and horizontally (with same ratio) to the screen size
4 : 3  video source
❖
Through mode
Images are shown at the same resolution as RGB/video signals. ❖
V-Stretch mode
The 2.35:1 image is shown across the entire screen. The vertical compone\
nt of the aspect ratio is
elongated in this case. 
7146@@&/(
 
 
 
 
 1.
 
 
						

							18
ENGLISH
•Press the  ZOOMbutton, the  NORMALbutton or the  FULLbutton on the remote controller for the 4:3
aspect ratio video source.
• Press the  FULLbutton on the remote controller for 16:9 aspect ratio video source, such\
 as 1080i,
1035i, and 720p video systems.
• Press the  FULLbutton on the remote controller for the squeezed video source.The Screen Images in a 4:3 screen❖
Original Source Image
❖
Full mode
The 16:9 squeezed image is displayed with the
correct aspect.❖
Normal mode
❖
Zoom mode
16 : 9  video source
The 4:3 image is enlarged horizontally.
The picture in normal ratio 4:3 is displayed.
The picture in normal ratio 4:3 is enlarged
vertically and horizontally (with same ratio) to the
screen size
4 : 3  video source
❖
Through mode
Images are shown at the same resolution as RGB/video signals.1.
Press the  STANDBY button on the remote controller or the  / Ibutton on the projector.
2.
The fan continues running for about 1 minute to internally cool the proj\
ector. In the meantime, the ON
indicator on the projector flashes a blue color and buttons on the proje\
ctor and remote control are
irresponsive to touch. Once the fan stops, the ON indicator goes out and\
 the STANDBY indicator
lights up a green color to indicate the projector is on standby.
Notes : - Do not pull out the AC power cord until the projector turns in standby m\
ode.
- Do not pull out the power cord suddenly in the state of  “POWER ON. It can cause a breakdown.
- If the WARNING indicator lights up or blinks a yellow color, check that \
the fan has stopped then unplug the AC power cord from its outlet.
- The projector will not be turned on if the  ONbutton on the remote controller or the  /  Ibutton on
the projector is pressed immediately after turning off.  Press the  ONbutton on the remote controller
or /  Ibutton on the projector after the projector turns into standby mode.
- When on standby, power to the projector is not OFF completely. If not pl\
anning to use the projector for an extended period of time, unplug the AC power cord from AC power o\
utlet as explained above.
C1 C2 S G1
H1 H2 V G2A1
A2 RGB G3
COMP.1 COMP.2 S-VIDEO USER
HDMI 1 HDMI 2 VIDEO
AUX 1 AUX 2
ON
STANDBYIRIS LAMP
C.TEMP GAMMA
To Turn off the Power❖
V-Stretch mode
The 2.35:1 image is shown across the entire screen.
7146@@&/(
 
 
 
 
 1.
 
 
						

							19
ENGLISH
OPERATIONSMenu Structure
Main Menu
Item Main Menu
Item
Component 1VideoRGB
Auto*480i/576i480p540p576p
720p1035i1080i1080p
Auto*480i/576i480p540p576p
720p1035i1080i1080p
Auto*NTSCPA LSECAM
RGB/HD AdjustMode
ReadjustResolution HResolution VPosition HPosition VPhaseClamp Position
Input Signal
Component 2
Auto*480i/576i480p540p576p
720p1035i1080i1080p
HDMI1
Auto*480i/576i480p576p720p
1035i1080i1080p
HDMI2
Auto*480i/576i480p576p720p
1035i1080i1080p
S-Video
Auto*NTSCPA LSECAM
CSC HDMI1
YPBPR 4:4:4
YPBPR 4:2:2
CSC HDMI2
RGBYPBPR 4:4:4
YPBPR 4:2:2
Yes / No*
Clamp Width25 0*
25 0*
0* 50
-50
0* 10
-10
Position HPosition VOverscan
0* 50
-50
0* 50
-50
0* 50
-50
0* 50
-50
0* 10
-10
P.25Config. (Configuration)Auto Power OFF
Remote ControlTrigger 2 FullTrigger 2 NormalTrigger 2 ThroughTrigger 2 ZoomReset Lamp Life
Enable / Disable*
On* / Off
On* / Off
On* / Off On* / Off
Trigger 2 V-Stretch
On* / Off
Yes / No
Yes / No Wireless* / Wired
Reset All
P.27DisplayKeystone
ScaleWidth
0* 25
-25
P.26
Menu Position
OSD/Blanking
Status Info. Enable* / DisableEnable* / DisablePower-OFF Confirm. Enable / Disable*Blanking Memory Off* / 1 / 2 / 3Blanking Top
0* 100Blanking BottomBlanking LeftBlanking Right0* 100
-100 0*-100 0*0* 1000* 100
Language
English*DeutschFrançaisEspañolTop-L*To pTop-RF + CeilingR + Ceiling
Installation
Front*RearF + Ceiling
R + Ceiling
Auto*Memory1Memory2
Memory3
P.26
P.25
Picture Mode
Theater
Main Menu
Item
Default* / 1 / 2 / 3
Default* / 1 / 2 / 3
Default* / 1 / 2 / 3
1* / 2 / 3 / 4 / 5 / 6 / 7 / 8 / 9
StandardDynamicUser
Picture Adjust
Aspect1 / 2 / 3 / 4 / 5 / HB
Iris F6.0* / F3.0
Full*NormalZoomV-StretchThrough
Gamma
ABCDE
TheaterStandardDynamic
Contrast
P.22Fine Menu 1
Sharpness
Noise ReductionR GainG Gain
P.24P.23
0* 50
-500* 500* 50
0* 50
-50
B Gain
0* 50
-50
R Bias
0* 50
-50
G Bias
0* 50
-50
B Bias
0* 50
-50
0* 50
-50
Fine Menu 2
Cinema
VCR ModeBlack Level
During HDMI input, “Expand” or “Normal” is shown.FRCCEC
P.24
Auto* / Off
On / Off*
On / Off* 0 IRE* / 7.5 IRE
Auto* / On
Luminance Gain
0* 50
-50
Picture Shift V
0* 50
-50
Chroma Delay
0* 5
-5
Brightness
0* 50
-50
Color
0* 50
-50
Tint
0* G50 R50
Color Temp.
Normal* / Economy
Lamp Mode
Center-RBottom-L
Center-L
Bottom
Center
Bottom-RPortuguêsItaliano
RGB Auto*
Auto* YC
BCR 4:2:2 YC
BCR 4:4:4
YC
BCR 4:4:4
YC
BCR 4:2:2
* Default setting
7146@@&/(
 
 
 
 
 1.
 
 
						

							20
ENGLISH
Functions by Signal
NO SIGNAL VALID SIGNAL
ANY INPUTVIDEO or S-VIDEO COMPONENT RGB HDMI
NTSC PAL/SECAM 480i/576i 480p/576p 480i/576i 480p/576p Other1080i/720p/
1080p/540p
Picture Mode Theater–
   
Standard–
   
Dynamic–
   
User–
   
Picture Adjust Gamma–*1 *1 *1 *1 *1 *1 *1 *1 *1
Contrast–*9 *9 *9 *9 *9 *9 *9 *9 *9
Brightness–*9 *9 *9 *9 *9 *9 *9 *9 *9
Color–*9 *9 *9 *9 *9 *9 *9 *9 *9
Tint–*9––– –– –– –
Color Temp.–*9 *9 *9 *9 *9 *9 *9 *9 *9
Lamp Mode–*9 *9 *9 *9 *9 *9 *9 *9 *9
Iris–*9 *9 *9 *9 *9 *9 *9 *9 *9
Aspect–
   
Fine Menu 1 Sharpness–*9 *9 *9 *9 *9 *9 *9 *9 *9
Noise Reduction–*9 *9 *9 *9 *9 *9 *9 *9 *9
R Gain–*9 *9 *9 *9 *9 *9 *9 *9 *9
G Gain–*9 *9 *9 *9 *9 *9 *9 *9 *9
B Gain–*9 *9 *9 *9 *9 *9 *9 *9 *9
R Bias–*9 *9 *9 *9 *9 *9 *9 *9 *9
G Bias–*9 *9 *9 *9 *9 *9 *9 *9 *9
B Bias–*9 *9 *9 *9 *9 *9 *9 *9 *9
Fine Menu 2 Cinema–

–*2

–*2 *2
VCR Mode
 
––––––
Black Level
  
–

*10

FRC
    
CEC– ––––*3––*3 *3
Picture Shift V–*4 *4 *4––––––
Luminance Gain–

––––––
Chroma Delay–

––––––
RGB/HD Adjust Mode– ––––

––

Readjust– ––––*5––*5 *5
Resolution H– ––––*6––*6 *6
Resolution V– ––––*6––*6 *6
Position H– ––––*5––*5 *5
Position V– ––––*5––*5 *5
Phase– ––––*5––*5–
Clamp Position– ––––*5––*5–
Clamp Width– ––––*5––*5–
7146@@&/(
 
 
 
 
 1.
 
 
						

							21
ENGLISH
NO SIGNAL VALID SIGNAL
ANY INPUTVIDEO or S-VIDEO COMPONENT
3(# )%.*
NTSC PAL/SECAM 480i/576i 480p/576p 480i/576i 480p/576p Other1080i/720p/
1080p/540p
Display Keystone–
   
Scale–
   
Width–
   
Position H–
   
Position V–
   
Overscan–

–

–*7
Installation
    
OSD/Blanking Menu Position
    
Language
    
Status Info.
    
Power-OFF Confirm.
    
Blanking Memory–
   
Blanking Top–*8 *8 *8 *8 *8 *8 *8 *8 *8
Blanking Bottom–*8 *8 *8 *8 *8 *8 *8 *8 *8
Blanking Left–*8 *8 *8 *8 *8 *8 *8 *8 *8
Blanking Right–*8 *8 *8 *8 *8 *8 *8 *8 *8
Configuration Auto Power Off
    
Trigger 2 Full
    
Trigger 2 Normal
    
Trigger 2 Zoom
    
Trigger 2 V-Strech
    
Trigger 2 Through
    
Remote Control
    
Reset Lamp Life
    
Reset All
    
*1 Can be selected only when User is selected for the Picture Mode.
*2 On only when interlaced signals are input. (Off for progressive signals.)
*3 On only when 1080i signals are input.
*4 On only when Aspect is set to Zoom or V-Stretch.
*5 On when the RGB/HD Adjust mode is set to Memory.
*6 On when the RGB/HD Adjust mode is set to Memory. However, as an exception, it is off when Aspect is set to Through.
*7 On when 480i/p or 576i/p signals are input.
*8 On when Blanking Memory is selected for OSD/Blanking.
*9 Cannot be selected when the default is selected for Picture Mode.
*10 Off when PC signals (1024 x 768, etc.) are input.
7146@@&/(
 
 
 
 
 1.
 
 
						

							22
ENGLISH
This projector has menus that make setting and adjustment easy.1.
Press the MENUbutton. The MENU screen appears on the screen.
2.
Use the 3and 4buttons to select a menu (Picture Adjust, Fine Menu 1, Fine Menu 2, Input Signal,
RGB/HD Adjust, Display, OSD/Blanking, Config) and press the 2button.
For image mode selection, see “Picture Mode”.  (

P.22)
3.
Use the 3and 4buttons to select a menu item and press the 2button.
4.
Use the 3, 4, 1and 2buttons to make the setting or adjustment of the selected item.
•The current setting or adjustment level is displayed to the right of each menu item.
5.
Press the MENUbutton again to close the menu.
– Adjustment bar
When there is a “” right of a menu item, this 2acts as a button for engaging an adjustment mode. In
the adjustment mode, the menu disappears and only an adjustment bar, like that shown below,
appears along the bottom of the display. Use the 1and 2buttons to adjust the item to the desired
level. Press the 3button to return to the menu.Contrast 0
INPUT V-MUTE
ENTERMENU
ASPECT
CINEMA
VCR MODE
BLACK LEVEL
PATTERN
BLACKINFO.I M
A
BLANKING
B1
OFF
B3
B2
1, 5
2, 3, 4
1, 5 2, 3, 4User 1
Gamma
Contrast
Brightness
Color
Tint
0
0
03 0
Lamp Mode Color Temp.
Normal AIris
F6.0
Full
C
D
E BA
Picture Adjust
Fine Menu 1
Fine Menu 2
Input Signal
RGB/HD Adjust
Display
OSD/Blanking
Config.
Theater
Standard
Dynamic
Aspect
How to Operate Menus
Main menu Menu item  Setting or adjustment level This unit has four picture modes: Theater, Standard, Dynamic and User. The picture quality recommended
by Marantz is already set for each mode. The User mode has eight gamma curves that can be chosen and
saved by users. Also, the Theater, Standard and Dynamic modes three indexes for memorizing picture
quality adjustments. Similarly, the User mode has nine, making a total of 18 indexes available for use. 
–Theater: Reproduces the black suited for movie software.
–Standard: Suited for normal movie software.
–Dynamic: Suited for visually dynamic image software.
–User 1-9: Enable the user to adjust the gamma curve as preferred.(

P.23).
Picture mode selection
There are two ways to select the Picture mode: selecting a mode from the MENU screen or pressing
the picture mode buttons (THTR, STD, DYN) on the remote controller. To use the remote controller
buttons to select a picture mode, make sure the MENU screen does not appear on the screen and
press the desired picture mode button any number of times. (

P.6)
To select an picture mode from the menu, do as follows.
1.Press the MENUbutton. The MENU screen appears on the screen.
2.Use the 3/4buttons to select the Picture Mode displayed at the top of the menu.
3.Press the ENTERbutton to display the picture mode selection screen. Use the 3, 4, 2and 1
buttons to select an picture mode.
4.Press the ENTERbutton to decide the selected picture mode. Once the mode has been
entered, the screen returns to the previous menu.
Memorizing settings in an index
The settings made in “Picture Adjust” and “Fine Menu 1” of the main menu are automatically
memorized in the currently selected picture mode. Therefore, first select an picture mode and index,
and then make settings.
Note: 
When default is selected, “Picture Adjust” and “Fine Menu 1” cannot be selected from the menu.
Theater
Standard
Dynamic
UserDefault
1
Default
1
Standard 1Picture Adjust
Fine Menu 1
Fine Menu 2
Input Signal
RGB/HD Adjust
Display
OSD/Blanking
Config.
2
3 1 Default
Picture Mode
Picture mode  IndexTheater Default, 1, 2, 3Standard Default, 1, 2, 3Dynamic Default, 1, 2, 3
User 1, 2, 3, 4, 5, 6, 7, 8, 9
7146@@&/(
 
 
 
 
 1.