Marantz Projector Vp 11s1 User Manual

23
ENGLISH
–Gamma setting
To change the type of Gamma curve, set the Picture Mode (

p.22) to User (1 – 9). Select “Gamma”
from the displayed menu followed by the desired gamma curve (A, B, C, D, E, Theater, Standard or
Dynamic).
–Color Temp. (Color Temperature)
1 : Red comes out strong. Color temperature is about 5250 K.
2 : Red is mildly strong. Color temperature is about 5800 K.
3 : Normal. Color temperature is about 6500 K.
4 : Blue is mildly strong. Color temperature is about 7500 K.
5 : Blue comes...

24
ENGLISH
–Cinema
Auto : Automatically selects the cinema mode when a video signal is input. 
NTSC: 3-2 pull down, PAL: 2-2 pull down
Off : Pull-down processing is not performed.
–VCR Mode
On : A projector is forced into the intra-field only deinterlacing mode.
Off : A projector is used with external field memories and operates in the full set of deinterlacing
modes, i.e., motion adaptive video deinterlacing and full frame film source deinterlacing
using 3:2 pulldown detection (2:2 pulldown for 625/50...

25
ENGLISH
Standard 1
Component 1
Component 2
S-Video
VideoAuto
Auto
Auto
Auto
RGB Auto
HDMI2
CSC HDMI1
CSC HDMI2 HDMI1 Auto
Auto
Auto
AutoPicture Adjust
Fine Menu 1
Fine Menu 2
Input Signal
RGB/HD Adjust
Display
OSD/Blanking
Config.
Input Signal
NTSC(NTSC-3.58)
: Conventional analog broadcasting used
mainly in USA, Canada, Taiwan, Korea, and
Japan.
PAL(PAL-4.43)
: Conventional analog broadcasting used
mainly in United Kingdom and Germany.
SECAM
: Conventional analog broadcasting used
mainly in France...

26
ENGLISH
–Keystone
Adjust trapezoid image to rectangle image.
–Scale
Reduces the image without changing the aspect ratio. The image can be reduced to about 70% the
original size.
–Width
Reduces the image width without changing the image height. The width can be reduced to about 75%
the original size.
–Position H, V
Adjust the position of the input signal. H adjusts the horizontal position of the input signal. V adjusts the
vertical position of the input signal. 
–Overscan
Selects whether to show or...

27
ENGLISH
–Auto Power Off
When the auto power off feature is set to Enable, power
to the projector automatically shuts off if no signals are
received and no operations are performed for about 10
consecutive minutes. If 9 minutes pass without the
projector receiving any signals or being operated in
anyway, the below message appears on the screen.
About 1 minute after the message appears on the screen, power to the projector shuts off.
Note:
After the above message appears on the screen, pressing any...

28
ENGLISH
CAUTION:
•Do not touch the lamp and the lamp unit
carelessly. It is extremely hot. Wait at least
one hour for the lamp to cool down before
handling.
•Do not loosen any screws except for those
mentioned below.
•The lamp may break if handled improperly.
•Do not use other than a Marantz
replacement lamp unit.❖
How to replace the Lamp Unit
PREPARATION:
When replacing the lamp, turn off the power for
the projector. After the cooling fan stops,
disconnect the power cord and wait for one
hour until...

29
ENGLISH
3.
Wait at the least one hour for the lamp and
lamp unit to cool down.
4.
Read the caution and warning labels on the
unit.
Lamp cover
WARNINGTHIS COVER IS PROVIDED WITH
INTERLOCK TO REDUCE THE RISK OF
EXCESSIVE ULTRAVIOLET RADIATION.
DO NOT DEFEAT ITS PORPOSE OR
ATTEMPT TO SERVICE WITHOUT
REMOVING COVER COMPLETELY.
MODEL NO. VP-16S1
 / U1M
AC 120V   60HZ   2.0ASERIAL NO.
CAUTION : HIGH PRESSURE LAMP 
MAY EXPLODED IF IMPROPERLY HANDLED. 
REFER SERVICING TO QUALIFIED SERVICE 
PERSONNEL.ATTENTION...

30
ENGLISH
If the lens becomes dirty or smudged, clean it with
a soft dry cloth only. Use optical lens cleaners that
are approved for eyeglasses or cameras. Do not
use a dampen cloth, detergent solution, or thinner.
It may damage the lens and remain as stains.
When replacement parts are required, be sure to
inform a Marantz authorized service center. Use
only replacement parts specified by Marantz.
Unauthorized substitutions may result in fire,
electric shock, or other hazards. And, the warranty
may not...

31
ENGLISH
Try the following troubleshooting before calling for service.1.
Are the connections made properly ?
2.
Are you operating the unit properly, following the instructions ?
If the unit does not operate properly, check the items shown in the following table.
If any trouble cannot be solved by the instructions below, malfunction of the internal circuitry is suspected; immediately unplug the AC power cord and contact
Marantz dealer or service center.TROUBLESHOOTINGNo power
Image is not
displayed....

32
ENGLISH
WARNING/LAMP indicator, ON indicator, and STANDBY indicator diagnose error mode of the projector as follows.
The lamp cover is not 
closed properly.
The lamp has failed, or 
the lamp is completely 
worn out.
Projector internal 
temperature is higher 
than the allowed level. 
Trouble has occurred 
with the fan.
Internal program error
Close the cover correctly.
Replace the lamp and 
reset lamp life.Check if anything is 
blocking the exhaust vent.
Shut power OFF and 
ON again.
OtherFan...