Marantz Projector Mount20 User Manual

							Model  MOUNT20 User Guide
VP-12 Series Projector Ceiling Mount 
						

							 
 
CEILING MOUNT
INSTALLATION INSTRUCTIONS
I
READ BEFORE INSTALLING EQUIPMENT
This product was designed and manufactured to meet strict
quality and safety standards.   There are, however, some
installation and operation precautions which you should be
particularly aware of. 
1.         should be read before the product is operate
2.         should be retained for future reference.
3.         operating instructions should be adhered to.
4.        be followed.
5.         
6.   
7.         contact your dealer .
8.   
9.         the projector.
11.       on a regular basis.
10.       the projector with this mount.  Contact your dealer to install the\
      projector for you.
W arning
Hardware List
Adjustment Ranges and Load  Allowances
The ceiling should be capable of supporting a weight
of at least five (5) times the projector(s) weight.
If it cannot, the ceiling must be reinforced. Proper
installation procedure by qualified personnel as outlined 
in the installation instructions must be adhered to.
Failure to do so could result in serious personal injury . 
Step 1
Step 2
Figure 2
Figure 1
1
233
4
3
33
3
2
Wire Access
14
8 5/8
Base Plate Connectors #1Projector Mount Ceiling Plate 1
Plate 1
Plate 2
Base Plate Connectors 
Plate 1 with
Horizontal Adjustment Plate 2 (Base Plate Connector 
Holes 
2
Ceiling WireAccess
7 5/8
10 5/8
Insert Base Plate connectors #
slots will give you 2 1/4 inches of lateral adjustment for projector alignment.
4
Base plate connector holes rotation adjustment.Attach horizontal adjustment Plate 2 to projector mount ceilingPlate 1 using the four (4) 3/8 (inch) nuts and washers provided.
1.  Four (4) 3/8 (inch) nuts2.  Four (4) 3/8 (inch) flat washers3.  Two (2) 8 (mm) screws4.  Eleven (1 1) 6 (mm) screws5.  Eight (8) 6 (mm) rubber washers
  6.  One (1) Ceiling Mount #1  7.  Two (2) Base Plate Connectors  8.  One (1) Horizontal  Tilt Plate #2  9.  One (1) Horizontal  Tilt Plate #310.  One (1) Projector Plate #4	 											
Horizontal Tilt (yaw)	 	 	                     +/-  10 degreesVertical  Tilt (tilt)	 			     +/-  20 degreesRotation					     +/-  15 degreesLateral Shift	 			     +/-   2Maximum Load  Allowance			               450 Lbs.
VP-12 SERIES PROJECTOR          
						

							 
Step 3
Step 2 B
Step 3 B
Figure 3
Figure 4Figure 6
Figure 5
Step 4
Wire Access
Wire Access1
3
1
2
222
22
2
2
2
3
1
3
Plate 3Plate 4
Plates 1 & 2Plate 3
Horizontal Adjustment Plate 2 (Figure 2) attached to 
Projector Mount Ceiling Plate 1.
Horizontal T ilting Plate 3 Projector Mounting Plate 4 
Install the combined plates (above) securely to the ceiling
structure in accordance with local commercial building 
standards.
Use suitable hardware in adequate quantity and size depending
on the installation requirements. (Please note that Projector
VP-12SX weighs 28.6 lbs. (13 kgs).
Attach Horizontal  Tilting Plate 3 to the previously combined
plates (already installed on ceiling) using the two (2) 8 (mm)
screws and four (4)
in Figure 
spacers and
(indicated 
Holes for 6mm screws 
Holes for 8mm screws 
Holes for 6mm screws with rubber washer and steel washer
Indicates ForwardPositioning of Mount
Indicates ForwardPositioning of Mount
T ilting CapabilityTilting Capability
Horizontal T ilting Plate 3  Attached to Plates 1 and 2.
The newly combined Plate 3 provides 10
horizontal tilt. When positioned, tighten with screws
provided.
12 1/4
17
continued over
Invert the projector and place it on a soft and flat 
surface. Align the three (3) rubber spacers provided 
with the three (3) 6(mm) mounting holes on the 
projector and secure with three (3) 6(mm) screws 
provided.
mounting holes              
						

							 
Step 4 
Figure 7Figure 8
1100 Maplewood DriveItasca, IL  60143Phone: 630 741-0300   Fax: 630 741-0301You can find your nearest authorized distributor or dealeron our website at: www .marantz.com
Printed in Canada2004
Work in a group of 2 or more to carry the projector and followmanufacturers guidelines for relocating as stated in the VP-12SXowners manual.
Lift and slide the projector onto the 6 (mm) screws previouslyinstalled in the metal studs of the plate on the ceiling (see arrowin Figure 7).  Tighten the 6 (mm) screws on both sides of the mount and install four (4) 6 (mm) screws and washers into the side of the projector Mounting Plate 4.
Projector Mounting Plate 4 Projector Mounting Plate 4 connected to Mounting Plate 3
Sequence of  Assembly of Projector Mounting Plates
Plate 3
Plate 2
Plate 1
Plate 4
20Tilt20Tilt
Projector Side
Mount Side
Step 2
Step 3
Step 4
Mounts Fully  Assembled 
Ceiling Side
Projector Side
Plate 4
CEILING         
						

							8.5
1.7
3.15
5.5
7.0
10.0
2.75
14.00
Dimensions
1100 Maplewood DriveItasca, IL  60143Phone: 630 741-0300   Fax: 630 741-0301You can find your nearest authorized distributor or dealeron our website at: www .marantz.comPrinted in Canada2004
CEILING SIDE
PLATE #1
6.50
5.00
1.375
Base Plate Connectors
2.5
3.8
5.5
2.5
3.8
1.0
1.7
0.9