Home > Marantz > Projector > Marantz Projector Mount10 User Manual

Marantz Projector Mount10 User Manual

    Download as PDF Print this page Share this page

    Have a look at the manual Marantz Projector Mount10 User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 38 Marantz manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.

    							Model MOUNT10 User Guide
    VP-10S1 DLP Projector Mount 
    						
    							 
     
    PROJECTOR MOUNT
    INSTALLA TION INSTRUCTIONS
    I
    READ BEFORE INST ALLING EQUIPMENT
    This product was designed and manufactured to meet strict
    quality and safety standards.   There are, however, some
    installation and operation precautions which you should be
    particularly aware of. 
    1.         should be read before the product is operate
    2.         should be retained for future reference.
    3.         operating instructions should be adhered to.
    4.        be followed.
    5.         
    6.   
    7.         contact your dealer .
    8.   
    9.         the projector.
    11.       on a regular basis.
    10.       the projector with this mount.  Contact your dealer to install the      projector for you.
    W arning
    Hardware List
    Adjustment Ranges and Load  Allowances
    The ceiling should be capable of supporting a weight
    of at least five (5) times the projector(s) weight.
    If it cannot, the ceiling must be reinforced. Proper
    installation procedure by qualified personnel as outlined 
    in the installation instructions must be adhered to.
    Failure to do so could result in serious personal injury . 
    Step 1
    Step 2
    Figure 2
    Figure 1
    1
    233
    4
    3
    33
    3
    2
    Wire Access
    14
    8 5/8
    Base Plate Connectors #1Projector Mount Ceiling Plate 1
    Plate 1
    Plate 2
    Base Plate Connectors 
    Plate 1 with
    Horizontal Adjustment Plate 2 (Base Plate Connector 
    Holes 
    2
    Ceiling WireAccess
    7 5/8
    10 5/8
    Insert Base Plate connectors #
    slots will give you 4 1/2 inches of lateral adjustment for projector alignment.
    4
    Base plate connector holes adjustment.
    Attach horizontal adjustment Plate 2 to projector mount ceilingPlate 1 using the four (4) 3/8 (inch) nuts and washers provided.
    1.  Four (4) 3/8 (inch) nuts2.  Four (4) 3/8 (inch) flat washers3.  Two (2) 8 (mm) screws4.  Fourteen (14) 6 (mm) screws5.  Eight (8) 6 (mm) rubber washers6.   Two (2) 8 (mm) rubber washers
    7.  Eight  (8) 6 (mm) flat washers8.  One (1) Ceiling Mount #19.   Two (2) Base Plate Connectors10. One (1) Horizontal  Tilt Plate #211. One (1) Horizontal  Tilt Plate #312. One (1) Projector Plate #4	 											
    Horizontal Tilt (yaw)	 	 	                     +/-   4 degreesVertical  Tilt (tilt)	 			     +/-   8 degreesRotation					     +/- 15 degreesLateral Shift	 			     +/- 4Maximum Load  Allowance			               450 Lbs.                                        
    						
    							 
    Step 3
    Step 2 B
    Step 3 B
    Figure 3
    Figure 4Figure 6
    Figure 5
    Step 4
    Wire Access
    Wire Access1
    3
    1
    2
    222
    22
    2
    2
    2
    3
    1
    3
    Plate 3Plate 4
    Plates 1 & 2Plate 3
    Horizontal Adjustment Plate 2 (Figure 2) attached to 
    Projector Mount Ceiling Plate 1.
    Horizontal T ilting Plate 3 Projector Mounting Plate 4 
    Install the combined plates (above) securely to the ceiling
    structure in accordance with local commercial building 
    standards.
    Use suitable hardware in adequate quantity and size depending
    on the installation requirements. (Please note that Projector
    VP-10S1 weighs 90.3 lbs. (41kgs).
    Attach Horizontal  Tilting Plate 3 to the previously combined
    plates (already installed on ceiling) using the two (2) 8 (mm)
    screws with rubber washers, steel washers and four (4)
    6
     
    metal washers into the welded metal studs (indicated Tighten halfway .
    Holes for 6mm screws with washer
    1
    111
    111
    holes for 6mm screws with rubber washersHoles for 8mm screws with rubber washer and steel washer
    Holes for 6mm screws with rubber washer and steel washer
    Indicates ForwardPositioning of Mount
    Indicates ForwardPositioning of Mount
    Tilting CapabilityTilting Capability
    Horizontal T ilting Plate 3  Attached to Plates 1 and 2.
    The newly combined Plate 3 provides 8
    horizontal tilt. When positioned, tighten with screws
    and washers provided.
    12 1/4
    17
    Invert the projector and place it on a soft and flat surface.  Alignthe six (6) rubber spacers provided with the six (6) 6 (mm)mounting holes on the projector and secure with the six (6) 6 (mm)
    screws provided.
    continued over                                                  
    						
    							 
    Step 4 
    Figure 7Figure 8
    1100 Maplewood DriveItasca, IL  60143Phone: 630 741-0300   Fax: 630 741-0301You can find your nearest authorized distributor or dealeron our website at: www .marantz.com
    Printed in Canada2004
    Work in a group of 4 or more to carry the projector and followmanufacturers guidelines for relocating as stated in the VP-10S1owners manual.
    Lift and slide the projector onto the 6 (mm) screws previouslyinstalled in the metal studs of the plate on the ceiling (see arrowin Figure 7).  Tighten the six (mm) screws on both sides of the mount and install four (4) 6 (mm) screws and washers into the side of the projector Mounting Plate 4.
    Projector Mounting Plate 4 Projector Mounting Plate 4 connected to Mounting Plate 3
    Sequence of  Assembly of Projector Mounting Plates
    Plate 1
    Plate 2
    Plate 3
    Plate 4
    8Tilt8Tilt
    Projector Side
    Mount Side
    Step 2
    Step 3
    Step 4
    Mounts Fully  Assembled 
    Ceiling Side
    Projector Side
    Plate 4                                                  
    						
    All Marantz manuals Comments (0)

    Related Manuals for Marantz Projector Mount10 User Manual