Life Fitness T5 5 Manual
Have a look at the manual Life Fitness T5 5 Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 1 Life Fitness manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
![](/img/blank.gif)
9 2 LIfe fItneSS t5 treaDmILL DeSIgn ILLuStratIon Running Belt / Running Deck Motor Cove r Right Upright Left Upright Water Bottle Holder Console iP od Dock ing Station Headphone Jack Contac t Hear t Rate Sensors Side R ail Base Fr ame Assembly Handlebar Ac tivity Z one On / Of Switch Po wer Cord Reading Rack Emergenc y Stop USB Port Rear Roller Adjustment Bolts FlexDeck® T5 with Track Console
![](/img/blank.gif)
10 3 aSSembLy 3.1 unpackIng For safety, and to save time and effort, read this Owner’s Manual completely before installing your Life Fitness Treadmill. Place the treadmill near where it will be used before beginning the unpa\ cking procedure. These unpacking instructions assume you have already done the following:\ Removed the top of the shipping carton. Removed the corrugate packing material. Removed these assembly instructions from the bridge assembly carton. The best method for unpacking the rest of the treadmill proceeds as foll\ ows: Remove the bridge assembly carton from the base unit. Break down the sides of the inner shipping carton. Remove the treadmill uprights from the shipping carton. Assemble the treadmill. Once assembly is complete: - Roll the treadmill off the shipping carton and to the location where it will be used. The treadmill is bolted to a wooden pallet. Before moving the treadmill \ base off the pallet you must remove two bolts inside the motor pan. FAILURE TO REMOVE THE TWO BOLTS CAN CAUSE PERSONAL INJURY OR DAMAGE TO YOUR TREADMILL. Remove the motor cover. Unscrew the two bolts with a 1/2 inch socket wrench. Discard the bolts and washers. Continue with the assembly instructions a\ s normal. 1/2” 1/2”
![](/img/blank.gif)
11 3.2 component LISt anD HarDware Identify the following components after unpacking your treadmill: 1Left UprightQty: 1 2M10 X 25MM Bolt Qty: 12 3M10 Star WasherQty: 12 4Right UprightQty: 1 5Bridge AssemblyQty: 1 6ConsoleQty: 1 7M10 X 25MM Socket Head Cap ScrewQty: 4 8Bridge CoverQty: 1 9#10 X 1/2 Phillips ScrewQty: 2 10#6 X 3/8 Phillips ScrewQty: 4 11CupQty: 2 12Accessory TrayQty: 1 M10 X 25MM BOLT (#2) M10 STAR WASHER (#3) #10 X 1/2” PHILLIPS SCREW (#9) #6 x 3/8” PHILLIPS SCREW (#10) M10 X 25MM SOCKET HEAD CAP SCREW (#7)
![](/img/blank.gif)
13 3 4 1 L2 3 1 2 3 8x8x 4 R L Finger ziehen Sie die Schrauben fest.
![](/img/blank.gif)
14 5 6 1 4 52 3 S ich erst elle n , d ass alle B efe stig un g st eile f e stg ezo gen si nd Nicht einklemmen keine Kabel.
![](/img/blank.gif)
16 9 1089 10 4x 2x Tuck any excess cable inside console. DO NOT PINCH ANY WIRES!
![](/img/blank.gif)
18 3.3 caLIbratIon Before using your treadmill please follow the calibration instructions b\ elow. Please stand to the side of your treadmill during calibration. 1. Turn treadmill on, or if on press the RESET key. 2. The console will display “PLEASE WAIT” or “WAIT”. 3. When “PLEASE WAIT” or “WAIT” disappears and the screen is blank press and hold the PAUSE key until “DIAGNOSTICS” appears. Once ”DIAGNOSTICS” appears, press ENTER. 4. Use the arrow keys to scroll through the diagnostics menu to “CALIBRA TION” or “CALIB”. 5. Press enter to select “CALIBRATION” or “CALIB”. 6. Press the START key located on the activity zone to begin calibration. 7. Your treadmill will now automatically cycle through a series of tests inc\ luding speed and incline adjustments in order to complete calibration. 8. When successfully completed the console will display “PASS”. ***If there was an error during calibration the console will display “F AIL”. ***If a failure occurred press STOP twice and restart the process at Step 1. ***If failure occurs again take note of the error number display and con\ tact Life Fitness Customer Support Services at 1-800-351-3737 (U.S.A. and Canada). 9. Upon successful completion press the RESET key three times to exit calibration mode.