Liesegang Projector Dv 410 User Manual

							ENGLISH-10ENGLISH-10
O O O O
P P P P
E E E E
R R R R
A A A A
T T T T
I I I I
O O O O
N N N N
S S S S
       
( ( ( (
c c c c
o o o o
n n n n
t t t t
i i i i
n n n n
u u u u
e e e e
d d d d
) ) ) )
Basic Operation
The basic operations shown in Table 3 is performed from the supplied remote control transmitter or
the projector control panel. Items indicated by (*) may be used from the control panel.
Table 3 . Basic Operation
ItemDescription
INPUT
SELECT
Select Input Signal (*):Press the INPUT button.RGB IN 1→RGB IN 2→DVI→VIDEO IN →S-VIDEO IN →COMPONENT VIDEO (→RGB IN 1)Select RGB Input : Press the RGB button.VIDEO IN / S-VIDEO IN / COMPONENT VIDEO →RGB IN 1 / RGB IN 2 / DVI
RGB IN 1 →RGB IN 2 → DVI (→RGB IN 1)
Select Video Input :Press the VIDEO button.RGB IN 1 / RGB IN 2 / DVI →VIDEO IN / S-VIDEO IN / COMPONENT VIDEO
VIDEO IN →S-VIDEO IN →COMPONENT VIDEO (→VIDEO IN)
• The selected signal name is displayed for approximately 3 seconds when the input
signal is changed.
POSITION
Set/Clear Position Adjustment Mode :Press the POSITION button.The [ ] icon is displayed in the POSITION mode.
Image Position Adjustment:Press the  , , and  buttons in the
POSITION mode.
• Valid only in the MAGNIFY mode with a video signal is input.
• After approximately 10 seconds of inactivity the [ ] icon is extinguished and the
POSITION mode is cleared automatically.
• , , and 
buttons may operate as the mouse control button. Refer to page 4.
RESET (*)
Initialise Each Item :Select an item and press the RESET button.
Initialise Position Adjustment :Press the RESET button and the
POSITION mode. This function is valid only when RGB signal is input.
• Valid except for the VOLUME, LANGUAGE and H PHASE.
• The RESET button may operate as the mouse control button. Refer to page 4.
MAGNIFY
Set MAGNIFY Mode : Press the MAGNIFY  button.
Move Magnified Area :Run the POSITION in the MAGNIFY mode.
Adjust Magnification :Press the MAGNIFY  /  button in MAGNIFY
mode.
Clear MAGNIFY Mode :Press the MAGNIFY  button.
• The MAGNIFY mode is cleared by running or setting the AUTO, ASPECT, INPUT
SELECT or VIDEO, or by changing the input signal.
OFF
FREEZE
Set/Clear FREEZE Mode :Press the FREEZE button. The [II] icon is
displayed, and the image frozen, in the FREEZE mode.
• The FREEZE mode is cleared by running or setting POSITION, VOLUME, MUTE,
Automatic Adjustment, BLANK ON/OFF, or MENU ON/OFF, or by changing the
input signal.
• Do not forget to clear frozen static images.
•  Strong light and obstacles will interfere with operation of the remote control transmitter.NOTE
EW
 
 
 
 1.
 
 
						

							ItemDescription
VOLUMEVolume Adjustment :Press the VOLUME / button.
MUTESet/Clear Mute Mode :Press the MUTE button. No sound is heard in the
MUTE mode.
AUTO
Automatic Adjustment at RGB Input :Press the AUTO button. Horizontal
position(H.POSIT), vertical position (V.POSIT),clock phase (H.PHASE),
and horizontal size(H.SIZE) are automatically adjusted. Use with the
window at maximum size in the application display.
Automatic Adjustment at Video Input :Press the AUTO button. A signal
type appropriate for the input signal is selected automatically. Valid only
when AUTO is set for VIDEO on the menu.
• This operation requires approximately 10 seconds. It may not function correctly
with some input signals.
BLANK
ON/OFFSet/Clear Blank Mode:Press the BLANK button. No image is displayed in
the Blank mode. The screen color is as set in BLANK on the Image menu.
MENU
ON/OFF (
*)
Menu Display Start/Stop:Press the MENU button.• The menu display is terminated automatically after approximately 10 seconds of
inactivity.
MENU
SELECT
Select Menu Type:Press the MENU SELECT button. Allows the user to
select the normal menu or the single menu. Only the selected item is
displayed on the single menu, and other items are displayed with the 
and  buttons as with the normal menu.
• Valid only when the Setup menu is used. Push the MENU SELECT button after
selecting items such as BRIGHTNESS.
• The MENU SELECT button may operate as the mouse control button. Refer to
page 4.
Normal menu Single menu
P.IN P.
MODESelect Mode of P.IN P. Display :Press the PinP button.
Small
→Large→P.IN P.off (→Small)
• Valid only at RGB IN 1, RGB IN 2 or DVI input.
KEYSTONE
Set / Clear KEYSTONE Mode(*):Press the KEYSTONE  button.
Select KEYSTONE Mode :Press the  /  button in the KEYSTONE
mode.  Vertical 
↔Horizontal
Adjust KEYSTONE :Press the / button.
• The image may not be appeared properly when this function is activated on same
input signals.
• The adjustable range of distortion correction will be different among input signals.
ENGLISH-11
ENGLISH
ENGLISH-11
O O O O
P P P P
E E E E
R R R R
A A A A
T T T T
I I I I
O O O O
N N N N
S S S S
       
( ( ( (
c c c c
o o o o
n n n n
t t t t
i i i i
n n n n
u u u u
e e e e
d d d d
) ) ) )
Items indicated by (*) may be used from the control panel.
Table 3. Basic Operation (continued)
CONTRAST-2
BRIGHT
CONTRAST
V POSIT
H POSIT
H PHASE
H SIZE
COLOR BAL R
COLOR BAL B
ASPECT0
-2
+1 
0
0 100
100
800SETUP INPUT OPT.IMAGE(MENU SELECT)
EW
 
 
 
 1.
 
 
						

							ENGLISH-12ENGLISH-12
O O O O
P P P P
E E E E
R R R R
A A A A
T T T T
I I I I
O O O O
N N N N
S S S S
       
( ( ( (
c c c c
o o o o
n n n n
t t t t
i i i i
n n n n
u u u u
e e e e
d d d d
) ) ) )
Setup MenuThe following adjustments and settings are possible
when SETUP is selected at the top of the menu. Part
of the Setup menu differs between RGB input and
video input. Select an item with the  and
buttons, and start operation. Use the Single menu to
reduce menu size (see Table 3, MENU SELECT).
Table 4. Setup Menu
VIDEO
S-VIDEO
COMPONENT VIDEO RGB IN 1
RGB IN 2
DVI
BRIGHT
CONTRAST
V POSIT
H POSIT
H PHASE
H SIZE
COLOR BAL R
COLOR BAL B
ASPECT0
-2
+1 
0
0 100
100
800SETUP INPUT OPT.IMAGEBRIGHT
CONTRAST
SHARPNESS
COLOR
TINT
H PHASE
COLOR BAL  R
COLOR BAL  B
ASPECT0
+1
+1
0
0
0
0
0SETUP INPUT OPT.IMAGE
ItemDescriptionRGB IN 1
RGB IN 2DVIVIDEOS-VIDEOCOMPONENT
BRIGHTAdjustment: Dark ↔Light ✔✔✔
CONTRASTAdjustment:Weak ↔Strong ✔✔✔
V POSITAdjustment:Down ↔Up ✔--
H POSITAdjustment:Left ↔Right ✔--
H PHASEAdjustment:Left ↔Right 
• Adjust to eliminate flicker.✔-✔
H SIZE
Adjustment:Small ↔Large • The image may not be displayed correctly if the horizontal
size is excessive. In such cases, press the RESET button,
and initialize the horizontal size.✔--
SHARPNESSAdjustment:Soft ↔Clear --✔
COLORAdjustment:Light ↔Dark --✔
TINTAdjustment:Red ↔Green • Valid only when NTSC or NTSC 4.43 signal is received.--✔
COLOR BAL RAdjustment:Light ↔Dark ✔✔✔
COLOR BAL BAdjustment:Light ↔Dark ✔✔✔
ASPECT
Select Image Aspect Ratio :
Full [ ] 
↔16:9[ ]  
Select Position of Image:
Press the  button while 16:9[ ] is selected.
Center
→Down →Up (→Center )
✔✔-
Select Image Aspect Ratio:
4:3[ ] 
↔16:9[ ] ↔4:3 small[ ]
Select Position of Image :
Press the  button while 16:9[ ] / 4:3 small[ ]
is selected.
Center
→Down→Up (→Center )• 4:3 small cannot be selected with the input of 720p or
1080i component.
• 4:3 small may not be displayed correctly with some input
signals.
--✔
EW
 
 
 
 1.
 
 
						

							ENGLISH-13
ENGLISH
ENGLISH-13
O O O O
P P P P
E E E E
R R R R
A A A A
T T T T
I I I I
O O O O
N N N N
S S S S
       
( ( ( (
c c c c
o o o o
n n n n
t t t t
i i i i
n n n n
u u u u
e e e e
d d d d
) ) ) )
Input MenuThe following functions are available when INPUT is selected on the
menu. Select an item with the and buttons, and start or stop
operation with the and buttons. The function indicated (**) are
effective on video input mode only, not on RGB input mode, except in
the P.IN P. window on RGB input mode.
Table 5. Input Menu
EXECUTE
CANCELAUTO
RGB
VIDEO
HDTV SETUP INPUT OPT.IMAGE
ItemDescription
AUTO
Automatic Adjustment at RGB Input: Select the EXECUTE with the
button.Horizontal position (H.POSIT), vertical position (V.POSIT), clock
phase (H.PHASE), and horizontal size (H.SIZE) are automatically adjusted.
Use with the window at maximum size in the application display.
Automatic Adjustment at Video Input: Select the 
EXECUTEwith the 
button. A signal type appropriate for the input signal is selected
automatically when 
EXECUTEis selected automatically. Valid only when
AUTO is set for VIDEO on the menu.
• This operation requires approximately 10 seconds. It may not function correctly with
some input signals. Pressing the AUTO button in this case may correct this problem.
• This function is the same as for the AUTO function in Basic operation.
RGB
Displays RGB Input Frequency:Displays the horizontal and vertical sync
signal frequencies for RGB input.
• Valid only at RGB input.
VIDEO (**)
Select Video Signal Type:Select the signal type with the  and 
buttons. Select NTSC, PAL, SECAM, NTSC4.43, M-PAL, or N-PAL as
appropriate for the input signal. The selection of AUTO enables and
executes the function AUTO (Automatic Adjustment at Video Input), except
for the N-PAL input.
• Use this function when the image becomes unstable (eg. the image becomes
irregular, or lacks color) at VIDEO/S-VIDEO input.
• Automatic Adjustment requires approximately 10 seconds. It may not function
correctly with some input signals. Pressing the AUTO button in this case may correct
this problem except for the N-PAL input.
• For the COMPONENT VIDEO input, this function is not effective and the signal
type is distinguished automatically. Refer to the item HDTV of the OPT. Menu for the
signal of HDTV.
HDTVSelect HDTV mode:Select the 1035i mode or 1080i mode suitable for the
input signal with the  /  button.
EW
 
 
 
 1.
 
 
						

							ENGLISH-14ENGLISH-14
O O O O
P P P P
E E E E
R R R R
A A A A
T T T T
I I I I
O O O O
N N N N
S S S S
       
( ( ( (
c c c c
o o o o
n n n n
t t t t
i i i i
n n n n
u u u u
e e e e
d d d d
) ) ) )
Image Menu
The following adjustments and settings are available when IMAGE is
selected on the menu. Select an item with the and buttons, and 
start or stop operation with the and buttons.
Table 6. Image Menu
BLANK
START UP
Desk Top
MIRROR
P. IN P. POSIT
P. IN P. INPUT
GAMMA
Desk TopORIGINAL
SETUP INPUT OPT.IMAGE
ItemDescription
BLANK
Select Blank Screen: Select the screen in case of the BLANK mode with the  /
button. The selected one (Desk Top, ORIGINAL or one colors) is displayed when the
BLANK mode is ON.
Desk Topis a mode that the customer-customized screen is displayed. This is the
blue screen at the factory setting. Refer to the description of Desk Top below.
ORIGINALis a mode that the factory fixed screen is displayed.
• When Desk Top or ORIGINAL is selected, the screen is going to the black after several minutes.
START UP
Select Start Up Screen:Select the screen in case of no signal input with the  /
button. The selected one (Desk Top, ORIGINAL or TURN OFF) is displayed when no
signal is input.
Desk Topis a mode that the customer-customized screen is displayed. This is the
blue screen at the factory setting. Refer to the description of Desk Top below.
ORIGINALis a mode that the factory fixed screen is displayed.
TURN OFFdisplays the blue screen.
• When Desk Top or ORIGINAL is selected, the screen is going to the black after several minutes.
Desk Top
Set Desk Top Mode:Select the EXECUTE with the  button to display the Desk
Top menu and set the Desk Top mode for BLANK and START UP functions.
ESCclears and closes the menu box.
NORM.is default of the Desk Top menu.
FREEZEfreezes the image and displays the frame to capture.
Press the  button after freeze to go to the Desk Top Capture Position mode.
In the Desk Top Capture Position mode,
the buttons  , , and  allow to
move the frame to capture.
After adjusting the position, press the KEYSTONE button to go to the Desk Top
Display Size mode.
To cancel freezing and return to the NORM. of the Desk Top menu, press the
RESET button.
In the Desk Top Display Size mode
, select the magnification x1, x2 or FULL with the
button  / . After selecting the magnification, press the KEYSTONE button to go
to the CAPT. mode and start capturing.
To return to the Desk Top Capture Position mode, press the RESET button.
CAPT.executes a capturing the image. It requires about 20 seconds. After capturing,
the captured image will be displayed for about 10 seconds.
MIRRORSelect Mirror Status:Select mirror status with  /  button.
P. IN P.
POSITSelect Position of P. in P. Display :Press the or button.
↔↔↔
• Valid only at RGB IN 1, RGB IN 2 or DVI input.
P. IN P.
INPUTSelect signal of P. in P. Display :Press the  or  button.
VIDEO ↔S-VIDEO 
GAMMASelect Gamma Mode:Select the gamma mode with the  /  button.
NORMAL ↔CINEMA ↔DYNAMIC
EW
 
 
 
 1.
 
 
						

							ENGLISH-15
ENGLISH
ENGLISH-15
O O O O
P P P P
E E E E
R R R R
A A A A
T T T T
I I I I
O O O O
N N N N
S S S S
       
( ( ( (
c c c c
o o o o
n n n n
t t t t
i i i i
n n n n
u u u u
e e e e
d d d d
) ) ) )
Options Menu
The following adjustments and settings are available when OPT. is
selected on the menu. Select an item with the and buttons, and
start or stop operation with the  and buttons. 
Table 7. Options Menu
VOLUMEMENU COLORLANGUAGE
AUTO OFF
SYNC ON G
WHISPER
IR REMOTE
16 SETUP INPUT OPT.IMAGE
ItemDescription
VOLUMEReduce ↔Increase 
MENU COLORSelect Menu Background Color:Select with the  /  button.
LANGUAGESelect Menu Display Language:Select with the  /  button.
AUTO OFF
Set AUTO OFF:Set 1~99 minutes with the  /  button. The system
automatically enters the standby mode when a signal is not received for
the set time.
Clear AUTO OFF:Select STOP (0 min.) with the  button. When
STOP is selected the system does not enter the standby mode even if
no signal is received.
SYNC ON G
SYNC ON G Valid:Select TURN ON with the  button.
SYNC ON G Invalid:Select TURN OFF with the  button.
• May not be displayed correctly with some input signals when SYNC ON G is
valid. In such cases, remove the signal connector so that no signal is received,
set SYNC ON G to invalid, and reconnect the signal.
WHISPER
Set / Crear WHISPER Mode: Press the  /  button.  When the
WHISPER is selected, the WHISPER mode is active. In the WHISPER
mode, acoustic noise level from the unit is reduced, and brightness level
on screen is a little lower.
IR REMOTE
Select Remote Control Sensor: Select the sensors to activate along
the menu with the  /  button. Use this function if the remote does
not work stably. The ambient light may affect the remote.
VOLUMEMENU COLORLANGUAGE
AUTO OFF
SYNC ON G
WHISPER
IR REMOTE SETUP INPUT OPT.
IMAGE
1 1
2 2
3
3
: active
: inactive
EW
 
 
 
 1.
 
 
						

							ENGLISH-16
O O O O
P P P P
E E E E
R R R R
A A A A
T T T T
I I I I
O O O O
N N N N
S S S S
       
( ( ( (
c c c c
o o o o
n n n n
t t t t
i i i i
n n n n
u u u u
e e e e
d d d d
) ) ) )
No Signal MenuThe same adjustments and settings are available as with the Image and
Options menus when the MENU button is pressed during display of the
“NO INPUT IS DETECTED ON ***” or “SYNC IS OUT OF RANGE
ON ***” message while no signal is received.Select an item with the
and buttons, and start or stop operation with the and buttons.
Table 8. No Signal Menu
VOLUME
BLANK
START UP
MIRROR
MENU COLORLANGUAGE
AUTO OFF
SYNC ON G
WHISPER
IR REMOTE
16
ItemDescription
VOLUME
Reduce ↔Increase • When this function is used, audio input is automatically switched to video. The audio input can
be switched by moving the DISK PAD left and right during the display of the volume adjustment
bar. The volume adjustment bar is displayed by pressing VOLUME  /  button.
BLANK
Select Blank Screen: Select the screen in case of the BLANK mode with the  /
button. The selected one (Desk Top, ORIGINAL or one colors) is displayed when the
BLANK mode is ON.
Desk Topis a mode that the customer-customized screen is displayed. This is the
blue screen at the factory setting. Refer to the description of Desk Top below.
ORIGINALis a mode that the factory fixed screen is displayed.
• When Desk Top or ORIGINAL is selected, the screen is going to the black after several minutes.
START UP
Select Start Up Screen:Select the screen in case of no signal input with the  / button.
The selected one (Desk Top, ORIGINAL or TURN OFF) is displayed when no signal is input.
Desk Topis a mode that the customer-customized screen is displayed. This is the
blue screen at the factory setting. Refer to the description of Desk Top below.
ORIGINALis a mode that the factory fixed screen is displayed.
TURN OFFdisplays the blue screen.
• When Desk Top or ORIGINAL is selected, the screen is going to the black after several minutes.
MIRRORSelect Mirror Status:Select the mirror status with the  /  button.
MENU COLORSelect Menu Background Color:Select the color with the  /  button.
LANGUAGESelect Menu Display Language:Select the language with the  /  button.
AUTO OFF
Set AUTO OFF:Set 1~99 minutes with the  /  button. The system
automatically enters the standby mode when a signal is not received for the set time.
Clear AUTO OFF:Select the STOP (0 min.) with the  button. When the STOP is
selected the system does not enter the standby mode even if no signal is received.
SYNC ON G
SYNC ON G Valid:Select the TURN ON with the  button.
SYNC ON G Invalid:Select the TURN OFF with the  button.
• May not be displayed correctly with some input signals when the SYNC ON G is valid. In such
cases, remove the signal connector so that no signal is received, set the SYNC ON G to invalid,
and reconnect the signal.
WHISPERSet / Crear WHISPER Mode: Press the  /  button.  When the WHISPER is
selected, the WHISPER mode is active. In the WHISPER mode, acoustic moise level
from the unit is reduced, and brightness level on screen is a little lower.
IR REMOTE
Select Remote Control Sensor: Select the sensors to activate along the menu with
the  /  button. Use this function if the remote does not work stably. The ambient
light may affect the remote.
VOLUME
BLANK
START UP
MIRROR
MENU COLORLANGUAGE
AUTO OFF
SYNC ON G
WHISPER
IR REMOTE1 1
2 2
3
3
: active
: inactive
EW
 
 
 
 1.
 
 
						

							ENGLISH-17
ENGLISH
MAINTENANCE MAINTENANCE
Lamp
HIGH VOLTAGE
HIGH TEMPERATURE
HIGH PRESSURE
Contact your dealer before replacing the lamp.
For the optional lamp, see the item “Optional Parts” of the Table 12.
Before replacing the lamp, switch power OFF, remove the power cord from the power outlet, and
wait approximately 45 minutes until the lamp has cooled. The lamp may explode if handled at high
temperatures.
Lamp Life
Projector lamps have a finite life. The image will become darker, and hues will become weaker,
after a lamp has been used for a long period of time. 
Replace the lamp if the LAMP indicator is red, or the CHANGE THE LAMP message appears
when the projector is switched ON. See Table 9 of P.20 and Table 10 of P.21.
•The LAMP indicator is also red when the lamp unit reaches high temperature. Before
replacing the lamp, switch power OFF, wait approximately 20 minutes, and switch power ON again.
If the LAMP indicator is still red, replace the lamp.NOTE
WARNINGAmercury lamp used in this LCD projector is made of glass and has high
internal pressure.  The mercury lamp can burst with a big noise due to deterioration
resulting from a shock, crack and passage of time, and can end its service life in unlit
condition.  Lamps also have a considerably different service life and can sometimes end up
in burst or turn to unlit condition soon after use.  Furthermore, when the lamp is blown up,
glass fragments can get scattered around the lamp house and some gas containing mercury
inside the lamp can leak out of the projector’s air vent.
• Handle the lamp with utmost care as it can burst during use if subjected to a shock or
impact or if scratched or cracked.
• Probability for the burst will increase if the lamp is used for extended period of time or
used exceeding the period of replacement.  You are advised to follow instructions for lamp
replacement as soon as they are given (Refer to Table 9 of Page 20, Table 10 of Page 21).
Avoid any reuse of an old lamp (used lamp) since such reuse can result in burst.
• In case the lamp gets blown up in a short period of time after use, some electrical failures
or troubles other than the lamp itself may be suspected as causes.  Under such
circumstances, consult the store where you purchased it or a service company.
• Should the lamp burst (accompanied by a big bursting noise), perform ventilation
sufficiently, and exercise maximum caution not to inhale any gas out of the projector’s air
vent or not to let it enter your eyes or mouth.
• Should the lamp burst (accompanied by a big bursting noise), make absolutely sure to
unplug the power cord from the outlet and ask the store where you bought the lamp for
immediate replacement.  You should not engage in cleanup or replacement of the lamp by
yourself since scattered glass fragments can damage the inside of projector or can result in
personal injury when you handle it. 
• When you dispose of any used lamps, be sure to observe and follow local ordinances and
regulations of the area or district where they are subjected to disposal.  Generally speaking,
the lamps are treated similarly as glasses and bottles in most cases, but there are areas or
districts where lamps are classified as a separate collection, and so be sure to use caution. 
• Never use the lamp in a state where the lamp cover is removed.
EW
 
 
 
 1.
 
 
						

							ENGLISH-18ENGLISH-18
M M M M
A A A A
I I I I
N N N N
T T T T
E E E E
N N N N
A A A A
N N N N
C C C C
E E E E
       
( ( ( (
c c c c
o o o o
n n n n
t t t t
i i i i
n n n n
u u u u
e e e e
d d d d
) ) ) )
Replacing the Lamp
1. Switch the projector OFF, remove the power cord from the
power outlet, and wait at least 45 minutes for the unit to cool.
2. Prepare a new lamp.
3. Check that the projector has cooled sufficiently, and gently
turn it upside down.
4. Loosen the two screws as shown in the diagram, and remove
the lamp cover.
5. Loosen the three screws, and gently remove the lamp while
holding the grips. Touching the inside of the lamp case may
result in uneven coloring.
6. Install the new lamp and tighten the three screws firmly.
Also steadily push the opposite side of the screwed lamp into
the unit.
7. Replace the lamp cover in position and tighten the  two
screws firmly.
8. Gently turn the projector right-side up.
Resetting the Lamp Timer
Reset the lamp timer after replacing the lamp. When the lamp has been replaced after the LAMP
indicator is red, or the CHANGE THE LAMP message is displayed, complete the following
operation within ten minutes of switching power ON. The power will be turned off automatically in
over 10 minutes.
1. Switch power ON, and press the RESET button, for approximately three seconds. The ‘LAMP
xxxx hr’ message will appear on the lamp timer on the bottom of the screen.
2. Press the MENU button on the remote control transmitter, or the RESET button on the control
panel, while the lamp timer is displayed. The ‘LAMP xxxx 
→0 CANCEL’ message will
then appear.
3. Press the  and select 0, and wait until the timer display is cleared.
•Do not reset the lamp timer without replacing the lamp. Reset the lamp timer always
when replacing the lamp. The message functions will not operate  properly if the lamp timer is not
reset correctly.NOTE
CAUTION• Ensure that screws are tightened
properly. Screws not tightened fully may result
in injury or accidents.
• Do not use the projector with the lamp cover
removed.
EW
 
 
 
 1.
 
 
						

							ENGLISH-19
ENGLISH
ENGLISH-19
M M M M
A A A A
I I I I
N N N N
T T T T
E E E E
N N N N
A A A A
N N N N
C C C C
E E E E
       
( ( ( (
c c c c
o o o o
n n n n
t t t t
i i i i
n n n n
u u u u
e e e e
d d d d
) ) ) )
Air Filter
Cleaning the air Filter
The air filter should be cleaned as described below at intervals of approximately 100 hours.
1. Switch the projector power supply OFF, and remove the power cord from the power outlet.
2. Clean the air filter with a vacuum cleaner.
Other Maintenance
Maintenance Inside the Equipment
For safety reasons, ensure that the equipment is cleaned and checked by the dealer once every two
years. Maintaining the equipment by yourself is dangerous.
Cleaning the Lens
Gently wipe the lens with lens cleaning paper. Do not touch the lens with your hands.
Cleaning the Cabinet and Remote control transmitter
Gently wipe with a soft cloth. If dirt and stains etc. are not easily removed, use a soft cloth
dampened with water, or water and a neutral detergent, and wipe dry with a soft, dry cloth.
CAUTION• Switch power OFF and remove the power cord from the power
outlet before beginning maintenance work. Please read the separate “Safety
Guide” thoroughly to ensure that maintenance is performed correctly.
• Do not use detergents or chemicals other than those noted above (e.g. benzene
or thinners).
• Do not use cleaning sprays.
• Do not rub with hard materials, or tap the equipment.
CAUTION• Switch power OFF and remove the power cord from the power
outlet before beginning maintenance work. Please read the separate “Safety
Guide” thoroughly to ensure that maintenance is performed correctly.
• Replace the air filter if contamination cannot be removed, or if it is damaged.
Contact your dealer in such case. For the optional air filter, see the item “Option
Parts” of the Table 12. 
• Do not use the equipment with the air filter removed.
• When the air filter is clogged with dust etc. the power supply is switched OFF
automatically to prevent the temperature rising inside the projector.
Replacing the Air Filter
Replace the air filter if contamination cannot be removed, or if it is damaged.
1. Remove the filter cover.
2. Remove the old filter.
3. Set the new filter and the filter cover.
•When this projector is brought into a warm room from a cold outdoor, condensation can
take place on the projection lens and mirror inside, blurring the screen and reducing your eyesight,
but do not worry.  The condensation will disappear and the screen will return to a normal condition
no sooner than the projector acclimates to the surrounding temperature.NOTE
EW
 
 
 
 1.