LG W2253tq Users Guide

Make sure to read the Important Precautionsbefore using the product. 
Keep the Users Guide(CD) in an accessible place for future reference.
See the label attached on the product and give the information to your
dealer when you ask for service.
W2053TQ
W2253TQ
User’s Guide
 

A1
This unit has been engineered and manufactured to ensure your personal safety,
however improper use may result in potential electrical  shock or fire hazards. In
order to allow the proper operation of all safeguards incorporated in this display,
observe the following basic rules for its installation, use, and servicing.
On Safety
Use only the power cord supplied with the unit. In case you use another power
cord, make sure that it is certified by the applicable national standards if not being
provided...

A2
Important Precautions
On Installation
Do not allow anything to rest upon or roll over the power cord, and do not place
the display where the power cord is subject to damage.
Do not use this display near water such as near a bathtub, washbowl, kitchen
sink, laundry tub, in a wet basement, or near a swimming pool.
Displays are provided with ventilation openings in the cabinet to allow the release
of heat generated during operation. If these openings are blocked, built-up heat
can cause failures which...

A3
Important Precautions
On Cleaning
Unplug the display before cleaning the face of the display screen.
Use a slightly damp (not wet) cloth. Do not use an aerosol directly on the display
screen because over-spraying may cause electrical shock.
When cleaning the product, unplug the power cord and scrub gently with a soft
cloth to prevent scratching. Do not clean with a wet cloth or spray water or
other liquids directly onto the product. An electric shock may occur. (Do not use
chemicals such as benzene,...

A4
Connecting the Display
Important
This illustration depicts the general model of connection. Your monitor may differ from
the items shown in the picture.
Do not carry the product upside down holding only the stand base. The product may
fall and get damaged or injure your foot.
Before setting up the monitor, ensure that the power to the monitor, the computer
system, and other attached devices is turned off.
Connecting the stand 
1.Place the monitor with its front facing downward on a soft cloth....

A5
Connecting the Display
Disassembling the stand
1.Put a cushion or soft cloth on a flat
surface.
3.Change your lock on the product as it follows and turn it in the arrow direction.
2.Place the monitor face down on
the cushion or soft cloth.
If you cant release the stand base even the locking rib is at a release position,
Please push the indicated rib down and retry it.
4.Pull out the stand to remove.
 

A6A6
Connecting the Display
Before setting up the monitor, ensure that the power to the monitor, the computer
system, and other attached devices is turned off. 
Positioning your display
1.Adjust the position of the panel in various ways for maximum comfort.
Tilt Range:-5˚~15˚ 
Ergonomic
It is recommended that in order to maintain an ergonomic and comfortable viewing
position, the forward tilt angle of the monitor should not exceed 5 degrees.
 

A7
Connecting the Display
Wall-outlet type
Power CordAnalog signal
D-subDigital signal
DVI
DVI-D (This feature is not available in all countries.)
Mac adapterFor Apple Macintosh use, a  separate plug
adapter is needed to change the 15 pin high
density (3 row) D-sub VGA connector on the
supplied cable to a 15 pin  2 row connector.
NOTEThis is a simplified representation of the rear view.
This rear view represents a general model; your display may differ from the view as shown.
User must use shielded...

A8
Connecting the Display
N E
P O
OPEN
12
3
E P
ON
4
Using the cable holder (This feature is not available in all models.)
Cable holder
 

A9
Control Function
Control Panel Functions
MENU ButtonUse this button to enter or exit from the On Screen Display.Use this button to enter EZ ZOOMING, 4:3 IN WIDE,
PHOTO EFFECTitems, for more information, refer to
page A18-A19.
OSD LOCKED/UNLOCKED
This function allows you to lock the current control settings, so
that these settings are not inadvertently changed. To lock the
OSD settings, press and hold the MENU buttonfor several
seconds. The message OSD LOCKED appears.
You can unlock the OSD settings at...