LG Projector PH300S User Manual

21REMOTE	CONTROL
REMOTE	CONTROL
Open the lid at the back of the remote control and insert the batteries as described in the  instructions. Use new batteries.

POWERMUTEINPUT
VOLUMEPA G E
PICTUREBLANK
EXIT
ꕣ
SETTINGS Q.MENU
STILL OK
RATIO USB
HELP KEY.S KEY.S
	POWER
Turns the projector on or off.
MUTE	
Mutes the sound of the projector.
INPUT	
Changes the input source.
VOLUME	+,	-
Adjusts the volume level.
PAGE	
,Moves to the previous/next page.
PICTURE
Changes the picture mode.
BLANK
Turns the projector...

22REMOTE	CONTROL
POWERMUTEINPUT
VOLUMEPA G E
PICTUREBLANK
EXIT
ꕣ
SETTINGS Q.MENU
STILL OK
RATIO USB
HELP KEY.S KEY.S
STILL
Freezes the moving image.
(Available in any mode other than USB 
mode.)
RATIO
Resizes an image.
USB
Accesses USB mode.
HELP
Enables the self-diagnosis.
KEY.S	
,
Adjusts Keystone.
Playback	Control	Buttons
Controls playback of MY	MEDIA.
Color	buttons
Sets detailed settings or gesture for each 
menu. 
•	When using the remote control, the 
optimal operation range is 3 meters or 
less...

23USING	THE	PROJECTOR
USING	THE	PROJECTOR
Using	the	battery

002F0052005A000300450044005700030057
•	It is displayed when the battery is running out.
•	As your battery is low, the projector will be turned off in a minute.
•	If the screen shows a low battery message, be sure to charge the battery.
Battery	using	time	information
StatusTime and Display
ChargingAbout 3 hours
Usage	Hours
About 2 hour
(Available battery using time about 2 hour when Energy Saving mode set to Max.
Changing the Energy Saving mode...

24USING	THE	PROJECTOR
•	If you do not intend to use the projector for a long time, leave the bat\
tery charged at 40 - 50 %.
•	The battery is automatically recharged when the projector is connected to a power supply.
•	Charge the battery fully when you first use the projector.
•	The battery standard usage time given in the manual is based on measurements taken by LG; the actual time may vary depending upon usage.
•	Battery usage time may vary depending on broadcast type, operating temperature, period of...

25USING	THE	PROJECTOR
Watching	Projector
Turning	the	Projector	On
The menu screen display in this owner's manual is an example to help users understand how to operate the product and may look different from the actual screen.
1 Connect the power cord correctly to turn the projector on.
2 Place the OFF/ON switch on the rear port area to ON and press the POWER button on the control panel or on the remote control. (If the switch is placed to OFF, the projector will not turn on.)
3 On the Language...

26USING	THE	PROJECTOR
Using	the	projector
1 When in standby mode, press the POWER button to turn the projector on.
2 Press the INPUT button and select the input signal you want.
3 Control the projector using the following buttons while watching the screen.
ButtonDescription
VOLUME	+,	-Adjusts the volume level.
MUTE	Mutes the sound of the projector.
Q.MENUEnters the quick menu. (See page 30.)
RATIOResizes an image.
KEY.S	,Adjusts Keystone. (See page 28.)
4 To turn the projector off, press the POWER button.  

27USING	THE	PROJECTOR
Additional	Options
Adjusting	Aspect	Ratio
1 Press the Q.MENU button.
2 Use the  ,  buttons to select Aspect	Ratio and press the OK button.
MenuDescription
16:9Resizes images to the 16:9 ratio.
Just	Scan
Displays the picture in the original size without cutting off the edges.
•	If you select Just	Scan, you may see image noise at the edge or edges of the screen.
Set	By	ProgramDisplays the picture in the same aspect ratio as the original image.
4:3Displays the screen with a 4:3 aspect...

28USING	THE	PROJECTOR
Using	the	Keystone	Function
To prevent the screen image from becoming trapezoidal, Keystone adjusts the top and bottom width of the image if the projector is not se\
t up at a right angle to the screen.
Because the Keystone function may cause inferior screen image quality, use this function only when it is not possible to set up the projector a\
t an optimal angle.

0003000306120003002E0048005C00560057000300130701002F0003003506FD
0026004F005200560048
1 Press the SETTINGS button.
2...

29USING	THE	PROJECTOR
Selecting	an	Input	Label
Displays which devices are connected to which input ports.

002C00510053005800570003002F004400450048004F
002B00270030002C
0026004F005200560048
1 Press the INPUT button on the remote control to display the input selection screen.
2 Press the Red button.
3 Use the  or  button to select one of the input labels.
Blank	Function
Using	the	Blank	Function
This function may be effective when you need to draw attention during a meeting or training.
1 Press the BLANK...

30USING	THE	PROJECTOR
Selecting	the	background	color	of	the	blank	image
1 Press the SETTINGS button.
2 Press the  ,  ,  , or  buttons to select OPTION	2 and press the OK button.
3 Press the  ,  buttons to select Blank	Image and press the OK button.
4 Press the  or  button to move to the setting or option you want and press the OK button.
Using	the	Quick	Menu
You can easily customize your frequently used menus.
1 Press the Q.MENU button.
2 Press the  or  button to select a menu and press OK button....