LG Projector Laser TV User Manual

21PREPARATION
Status Indicator
Operation/Status Indicator
Operation/
Status Indicator
OffPower standby state (Power is off.)
RedPower standby state
WhiteWarm stand-by (Power standby state)
White (Brightness 
changes slowly.)
The Laser TV is in the process of turning 
on or off.
OffIn operation
Red (blinking)High temperature warning
Red (blinking) + 
Purple once (blinking)
The Laser TV has turned off due to the 
high temperature.
Red (blinking) + 
Purple twice (blinking)
There may be a problem inside the...

22PREPARATION
Installation
Installation Precautions
• Place the product in a well-ventilated 
environment.
 -To prevent the internal heat from 
building up, install the Laser TV in a 
well-ventilated place.  
Do not place anything near the 
Laser TV. That may block its air 
vents. If the air vents are blocked, 
the internal temperature will 
increase.
 -Do not place the Laser TV on a 
carpet or rug. If a product has its 
inlet vent on its bottom, do not block 
the vent and use the product on a 
leveled...

23PREPARATION
Projection Distance per Screen Size
1 Place the Laser TV on a sturdy level surface, together with the computer or audio/
video source.
2 Place the Laser TV at an appropriate distance away from the screen. The distance 
between the Laser TV and the screen determines the actual size of the image.
3 Position the Laser TV so that the lens is perpendicular to the screen. If the lens 
is not perpendicular to the screen, the image displayed on the screen may be 
distorted. To correct the...

24PREPARATION
Kensington Security System
• This the Laser TV has a Kensington Security Standard connector to prevent theft. 
Connect a Kensington Security System cable as shown below.
• For more information on installation and use of the Kensington Security System, 
refer to the user guide provided with the Kensington Security System.
• The Kensington Security System is an optional accessory.
• What is Kensington? 
Kensington is a company that provides safety systems for laptops and other 
electronic...

25REMOTE CONTROL
REMOTE CONTROL
Open the battery cover on the back of the remote control 
and insert the batteries which is specified in the battery 
room with   poles pointing in the correct direction. 
The new and same type of batteries (1.5 V AAA) must 
be used.
• Do not mix new batteries with old ones.
CAUTION
HQHUJ\
VHWWLQJV
HGJH#DGMDXWR EODQN
UDWLR
LQSXW
VDYLQJ
IODVKENOLVW
YRO FKS
D
J
HIDY
LQIR Rl
PXWH T1PHQX
P\#DSSV
KRPH
RN
EDFNDY#PRGHH[LW
VWLOO
POWER
Turns the Laser TV on or off.
ENERGY SAVING...

26REMOTE CONTROL
HQHUJ\
VHWWLQJV
HGJH#DGMDXWREODQN
UDWLR
LQSXW
VDYLQJ
IODVKENOLVW
YRO FKS
D
J
H
IDY
LQIR Rl
PXWH T1PHQX
P\#DSSV
KRPH
RN
EDFNDY#PRGHH[LW
VWLOO
SETTINGS
Displays or closes the Settings menu.
HOME
Displays the Home menu.
HOME
,6³
1.ú
,^,î
²,^*[/î8¢&,ÿ
? MY APPS/Q.MENU
MY APPS: Displays the list of my apps.
Q.MENU: Changes the settings easily.
Up/Down/Left/Right buttons
Switches between menu functions.
OK 
Shows the current mode and saves changes to the 
settings.
 BACK
Returns to the...

27MAGIC REMOTE CONTROL
MAGIC REMOTE CONTROL
If the battery low message appears while using the Laser 
TV, replace the batteries.
As shown in the figure, press the top of the battery cover 
and slide it down the cover. Insert two new and identical 
alkaline batteries (1.5V, AA type) with + and - poles 
pointing in the correct direction in the remote control.
• Do not mix new batteries with old ones.
CAUTION
PUSH
YRO FK
P\#DSSV/T1PHQX
?
HOME
BACK
Pointer Signal Transmitter
HOME
,6³
1.ú
,^,î...

28MAGIC REMOTE CONTROL
Pairing the Magic Remote Control
You must pair the Magic remote control with the Laser TV to use it.
Pair the Magic remote control prior to use as follows:
1 Turn on the Laser TV and press the  Wheel (OK) button towards the Laser TV. 
When the pairing is complete, the pairing completion message is displayed on the 
Laser TV screen.
2 If the remote failed to pair, turn the Laser TV off and on and try pairing again by 
pressing the  Wheel (OK) button.
Re-pairing the Magic Remote...

29Setting Up the TV
Setting Up the TV
Connecting the Antenna 
or Cable
To watch TV using an indoor/outdoor 
antenna, connect a wall terminal and the 
antenna port of the Laser TV using an  
RF cable (75 Ω). 
You can watch public TV or cable (analog, 
digital) TV.
ANTENNA/CABLE IN
• Be careful not to bend the copper 
wire when connecting the coaxial 
cable (75Ω). 
 Fasten the cable connection 
terminal by turning it clockwise.
Copper Wire
• Ensure you use a standard coaxial 
cable (75Ω) when connecting to...

30Setting Up the TV
Setting Up the TV
Initial Setup
1 Connect the antenna and power cord correctly.
2 After waiting for a moment, press the POWER button on the remote control or the 
control panel. 
3 When you turn on the Laser TV for the first time, a setting screen appears as shown 
below. 
Here, you can specify the items required for watching the Laser TV more easily.