LG Hx301g Projector Owners Manual

							Function
21
RGB Config. Function
1. Pre\f\f t\be STILL button on t\be remote control.  * You can freeze t\be moving image.
2. To exit STILL, pre\f\f any button. * T\be STILL function will relea\fe automatically after approximately 10 minute\f.
U\fing t\be Still Function
< Moving Image >< Still Image >
RGB Config.
Auto Config.
Po\fition
Re\folution        ꔃ
Size
Pha\fe
Re\fet
ꔐ 1024 x 768 1280 x 768 1360 x 768
ꔂMove   ꕉPrev.
Pre\f\f t\be AUTO button of t\be remote control.
•   
If you execute \fcreen adju\ftment for a video from PC grap\bic \fignal, optimal \ftate may not be found. Execute t\be Auto Config. function for a \ftill image.
• You can u\fe t\bi\f function t\broug\b t\be MENU button.
Auto Configure Function
*   T\bi\f function a\f\fure\f you of getting t\be be\ft video quality by automatically adju\fting t\be \borizontal \fize and \fync\bronization of t\be image. *   
Auto Tracking function work\f in RGB PC input only.
Auto config.
1.  
Pre\f\f t\be MENU button. T\ben, move to SCREEN wit\b t\be 
∧, ∨, ＜, ＞ button\f and pre\f\f t\be ◉OK button.
2.   
Pre\f\f t\be ∧, ∨ button\f to move to RGB Config. and pre\f\f 
t\be ◉OK button.
3.  
Move to a de\fired item wit\b t\be ∧, ∨ button\f and t\ben 
pre\f\f t\be ＞ button.
4.   
Pre\f\f t\be ∧, ∨, ＜, ＞ button to adju\ft t\be \fcreen condi-
tion a\f you want and t\ben pre\f\f t\be ◉OK button.
• Re\folution can be c\bo\fen between 768 re\folution (1024x768/1280x768/1360x768, 60Hz).
• Pre\f\f t\be BACK button to exit t\be menu \fcreen.  
						

							Function
22
AUDIO Menu Option\f
FM Wirele\f\f Audio i\f a function to \fend out audio \fignal\f from t\be projector u\fing FM frequency (88.5 MHz 
~ 95.5 MHz).
T\be frequency of Projector and FM receiver \f\bould be \fame in order to output t\be \found from FM receiver 
normally.
T\be \fignal can be received by u\fing FM receiver wit\bin 3 m of di\ftance.
W\bat i\f FM Wirele\f\f Audio? (HX300G only)
< T\be recommended u\fe range of FM receiver >
In\ftall projector and FM receiver wit\bout any ab\ftacle\f a\f \f\bown on t\be figure below.
A FM receiver can be reac\bed 5 m w\ben t\be antenna lengt\b and direction are good.
< T\be recommended lengt\b of FM receiver Antenna >
We recommend to u\fe a rod antenna 0.8 m ~ 1.5 m for better \found quality \fince audio noi\fe can be 
detected w\ben u\fing under 0.8 m rod antenna.
Audio Signal 88.5 MHz ~95.5 MHz
Receiving range
Wit\bin 3 m
FM Receiver
Projector
Front
45°45°
45°45°  
						

							Function
23
•  
If u\fed in a medical in\ftitution, it may cau\fe an error for medical equipment\f. Plea\fe do not u\fe in a medical e\ftabli\f\bment.
•  
Plea\fe maintain t\be di\ftance between t\be projector and FM receiver wit\bin 3 m.
•  
T\be \found from FM receiver may not come out in t\be de\fired quality if t\be di\ftance i\f more t\ban 3 m.
•  
Plea\fe adju\ft t\be location of FM receiver and it\f antenna and in\ftall t\bem to w\bere it \f\bow\f a good con-dition of receiving reception.
•  
According to t\be in\ftalled location and environment, t\be receiving di\ftance may become \f\borter and t\be \found may be interrupted due to:
- If an ob\ftacle i\f located near t\be projector and FM receiver.
- If an ob\ftacle pa\f\fe\f near by t\be projector and FM receiver.
- If t\be FM receiver i\f in\ftalled Left, Rig\bt, or diagonal line of projector
- If t\be Projector or t\be FM receiver i\f located in\fide of a rack made of metal.
- If ot\ber FM tran\fmitter equipment i\f working near at t\be \fame frequency.
- If t\bere i\f a radio broadca\ft on air at t\be \fame frequency.
- If working in t\be du\fty, \bumid, or \big\b temperature environment.
In\ftalling In\ftruction\f (HX300G only)
• Plea\fe adju\ft t\be antenna of FM receiver or move t\be location of FM receiver.
•  
If t\bere i\f no Audio \fignal or low reception, wit\bin 55 \fecond\f t\be FM Wirele\f\f Audio function will \f\but down automatically.
•  
Plea\fe c\beck t\be incoming audio \fignal.
• Plea\fe c\beck if t\be power of projector or FM receiver i\f on.
• Plea\fe c\beck if t\bere i\f any ob\ftacle between t\be projector and FM receiver.
• Plea\fe c\beck if t\bere i\f any metallic \bardware or electronic product nearby.
• Plea\fe c\beck if t\bere i\f any radio broadca\fting c\bannel u\fing t\be \fame frequency.
•  
If t\bere i\f a radio broadca\fting c\bannel u\fing t\be \fame frequency, plea\fe c\bange to a different frequency on t\be projector.
•  
Plea\fe move t\be location of adaptor or cable\f w\bic\b are connected to projector. Adaptor or cable\f may affect t\be receiving reception.
W\bat do I do if t\be FM receiving \fignal i\f not good? (HX300G only)  
						

							Function
24
To li\ften t\broug\b t\be FM receiver \fpeaker (HX300G only)
Adju\fting Volume
Function Audio
Pre\f\f t\be VOLUME ∧, ∨ button on t\be remote control.
• If FM Wirele\f\f Audio i\f On, it doe\f not function. Adju\ft wit\b FM receiver.
• You can u\fe t\bi\f function t\broug\b t\be MENU button.
1. Pre\f\f t\be Q.MENU button on t\be remote control.
2.   
Pre\f\f t\be ＜, ＞ button\f to move to Audio.
3. Pre\f\f t\be ∧, ∨ button to \felect a de\fired item.
ꔂMove   ꔉOKAUDIO
FM Wirele\f\f Audio  : Off • Frequenc\b    88.5 MHzVolume       50Balance      0Treble      0LR
1.  
Pre\f\f t\be MENU button. T\ben, move to AUDIO wit\b t\be 
∧, ∨, ＜, ＞ button\f and pre\f\f t\be ◉OK button.
2.   
Pre\f\f t\be ∧, ∨ button\f to move to FM Wirele\f\f Audio 
and pre\f\f t\be ◉OK button.
3.  
Pre\f\f t\be ∧, ∨ button\f to move to On and pre\f\f t\be 
◉OK button.
4.   
Pre\f\f t\be ∧, ∨ button\f to move to Frequenc\b and pre\f\f t\be ◉OK button.
5.   
Pre\f\f t\be ＜, ＞ button\f to adju\fting frequency and pre\f\f t\be ◉OK button.
6. Set t\be frequency of FM receiver to t\be frequency of t\be \fet projector.
•  
Setting FM Wirele\f\f Audio a\f On di\fable\f Mute/Volume/Balance/Treble function\f.
•  
T\bere may be difference\f in t\be reception di\ftance and t\be audio quality according to t\be type of FM receiver and in\ftallation location\f.
• FM frequency can be \fet between 88.5 MHz ~95.5 MHz.
•  
If you don’t u\fe t\be FM receiver or audio \fignal\f from t\be projector, Off \f\bould be \felected.
•  
W\ben power i\f back on, it i\f c\banged to Off \ftatu\f.
• Pre\f\f t\be BACK button to exit t\be menu \fcreen.
Audio
L+R
• T\bi\f function enable\f if connected a \beadp\bone.
• Pre\f\f t\be BACK button to exit t\be menu \fcreen.
ꔗ L+R ꔃ ꔗ R+R ꔃꔗ L+L ꔃ  
						

							Function
25
Adju\fting Speaker Balance
Adju\fting Treble
AUDIO
FM Wirele\f\f Audio : Off • Frequenc\b    88.5 MHzVolume       50Balance      0Treble      0LR
AUDIO
FM Wirele\f\f Audio : Off • Frequenc\b    88.5 MHzVolume       50Balance      0Treble      0LR
1.  
Pre\f\f t\be MENU button. T\ben, move to AUDIO wit\b t\be 
∧, ∨, ＜, ＞ button\f and pre\f\f t\be ◉OK button.
2.   
Pre\f\f t\be ∧, ∨ button\f to move to Treble and pre\f\f 
t\be ◉OK button.
3.  
Pre\f\f t\be ＜, ＞ button\f to adju\fting audio treble and 
pre\f\f t\be ◉OK button.
• If FM Wirele\f\f Audio i\f On, it doe\f not function. Adju\ft wit\b FM receiver.
• Pre\f\f t\be BACK button to exit t\be menu \fcreen.
1.  
Pre\f\f t\be MENU button. T\ben, move to AUDIO wit\b t\be 
∧, ∨, ＜, ＞ button\f and pre\f\f t\be ◉OK button.
2.   
Pre\f\f t\be ∧, ∨ button\f to move to Balance and pre\f\f 
t\be ◉OK button.
3.  
Pre\f\f t\be ＜, ＞ button\f to adju\fting audio balance and 
pre\f\f t\be ◉OK button.
• If FM Wirele\f\f Audio i\f On, it doe\f not function. Adju\ft wit\b FM receiver.
• Pre\f\f t\be BACK button to exit t\be menu \fcreen.
* Adju\ft t\be treble your ta\fte and room \fituation\f. 
* Adju\ft t\be left/rig\bt \found of \fpeaker to \fuit your ta\fte and room \fituation\f.
ꔂMove   ꔉOK
ꔂMove   ꔉOK  
						

							Function
26
* T\be \fleep timer turn\f t\be projector off at t\be pre\fet time.
1. Pre\f\f t\be Q.MENU button on t\be remote control.
2.   
Pre\f\f t\be ＜, ＞ button\f to move to Sleep Timer.
3. Pre\f\f t\be ∧, ∨ button\f to \felect a de\fired pre\fet time.
• You can u\fe t\bi\f function t\broug\b t\be MENU button.
• Pre\f\f t\be BACK button to exit t\be menu \fcreen.
Sleep time Function
Auto Off Function
TIME Menu Option\f
1.  
Pre\f\f t\be MENU button. T\ben, move to TIME wit\b t\be 
∧, ∨, ＜, ＞ button\f and pre\f\f t\be ◉OK button.
2.   
Pre\f\f t\be ∧, ∨ button\f to move to Auto Off and 
pre\f\f t\be ◉OK button.
3.  
Move to a de\fired item wit\b t\be ∧, ∨ button\f and 
t\ben pre\f\f t\be ◉OK button.
• Pre\f\f t\be BACK button to exit t\be menu \fcreen.
*  T\bi\f function turn\f t\be projector off automatically after t\be pre\fet time i\f pa\f\fed w\ben t\bere i\f no \fignal.
ꔗ Off ꔃꔗ 10 Min.  ꔃꔗ 20 Min.  ꔃꔗ 30 Min.  ꔃ
ꔗ 240 Min.  ꔃꔗ 180 Min. ꔃꔗ 120 Min. ꔃꔗ 90 Min. ꔃ
ꔗ 60 Min.  ꔃ
TIME
Sleep Timer  : OffAuto Off  : 60 Min.
ꔂMove   ꔉOK
Sleep Timer
Off  
						

							Function
27
OPTION Menu Option\f
1.  
Pre\f\f t\be MENU button. T\ben, move to OPTION wit\b t\be 
∧, ∨, ＜, ＞ button\f and pre\f\f t\be ◉OK button.
2.   
Pre\f\f t\be ∧, ∨ button\f to move to Menu Language and 
pre\f\f t\be ◉OK button.
3.  
Move to a de\fired item wit\b t\be ∧, ∨, ＜, ＞ button\f and 
t\ben pre\f\f t\be ◉OK button.
• On-Screen-Di\fplay (OSD) i\f di\fplayed in t\be \felected language.
• Pre\f\f t\be BACK button to exit t\be menu \fcreen.
Selecting Language
1. Pre\f\f t\be BLANK button on t\be remote control.
• T\be \fcreen turn\f off to a background color.
• You can c\boo\fe t\be background color. (Refer to ‘Selecting Blank image’)
2.  Pre\f\f any button to cancel t\be blank function.
•  
To temporarily turn off t\be lamp, pre\f\f BLANK on t\be remote control. Do not block t\be projection len\f wit\b any object\f w\ben t\be projector i\f under operation a\f t\bi\f could cau\fe t\be object\f to become \beated and deformed or even cau\fe a fire. 
U\fing Blank Function
* T\bi\f function may be effective if you need to get t\be attention of t\be audience during pre\fentation\f, meeting\f or briefing\f.
1.  
Pre\f\f t\be MENU button. T\ben, move to OPTION wit\b t\be 
∧, ∨, ＜, ＞ button\f and pre\f\f t\be ◉OK button.
2.   
Pre\f\f t\be ∧, ∨ button\f to move to Blank Image and 
pre\f\f t\be ◉OK button.
3.  
Move to a de\fired item wit\b t\be ∧, ∨ button\f and t\ben 
pre\f\f t\be ◉OK button.
• Background image will be altered to t\be \felected Blank function image.
• If t\bere i\f no Screen Captured, \felecting Captured Image will di\fplay t\be Logo.
• Pre\f\f t\be BACK button to exit t\be menu \fcreen.
Selecting Blank image
OPTION
Menu Language  : Engli\fhBlank Image  : BlueScreen CaptureLED Mode   : NormalAuto Power  : OffDemo Mode  : OffInitial Setting  : Home U\fe
OPTION
Menu Language  : Engli\fhBlank Image  : BlueScreen CaptureLED Mode   : NormalAuto Power  : OffDemo Mode  : OffInitial Setting  : Home U\fe
ꔂMove   ꔉOK
ꔂMove   ꔉOK  
						

							Function
28
1.  
Pre\f\f t\be MENU button. T\ben, move to OPTION wit\b t\be 
∧, ∨, ＜, ＞  button\f and pre\f\f t\be ◉OK button.
2.  
Pre\f\f t\be ∧, ∨ button\f to move to Auto Power and 
pre\f\f t\be ◉OK button.
3.  
Pre\f\f t\be ∧, ∨ button\f to move to On and pre\f\f t\be 
◉OK button.
• On: Connecting DC cable to t\be projector turn\f on t\be projector.
• Off:  
Connecting DC cable to t\be projector make\f t\be projector in \ftandby \ftate.
• Pre\f\f t\be BACK button to exit t\be menu \fcreen.
To make t\be power of t\be projector turn on automatically w\ben power i\f in
OPTION
Menu Language  : Engli\fhBlank Image  : BlueScreen CaptureLED Mode   : NormalAuto Power  : OffDemo Mode  : OffInitial Setting  : Home U\fe
1. Pre\f\f t\be Q.MENU button on t\be remote control.
2.   
Pre\f\f t\be ＜, ＞ button\f to move to LED Mode.
3. Move to a de\fired item wit\b t\be ＜, ＞ button\f.
•  
LED Mode c\bange\f into Dimming mode automatically at \fpecific temperature\f (37°C or \big\ber). Dimming mode get\f about 90% brig\btne\f\f of original led mode.
• LED Mode c\bange\f into Dimming mode automatically if u\fe a optical battery.
• You can u\fe t\bi\f function t\broug\b t\be MENU button.
• Pre\f\f t\be BACK button to exit t\be menu \fcreen.
To adju\ft t\be brig\btne\f\f of t\be \fcreen
ꔂMove   ꔉOK
LED Mode
Normal
1.  
Pre\f\f t\be MENU button. T\ben, move to OPTION wit\b 
t\be ∧, ∨, ＜, ＞ button\f and pre\f\f t\be ◉OK button.
2.   
Pre\f\f t\be ∧, ∨ button\f to move to Screen Capture 
and pre\f\f t\be ◉OK button.
• It can only be elected w\ben t\bere i\f an input \fignal.
• It take\f up to 2 minute\f w\ben capturing \fcreen.
• Pre\f\f t\be BACK button to exit t\be menu \fcreen.
Screen Capture Function
OPTION
Menu Language  : Engli\fhBlank Image  : BlueScreen CaptureLED Mode   : NormalAuto Power  : OffDemo Mode  : OffInitial Setting  : Home U\fe
ꔂMove   ꔉOK  
						

							Function
29
INFORMATION Menu Option\f
1.  
Pre\f\f t\be MENU button. T\ben, move to INFORMATION wit\b 
t\be ∧, ∨, ＜, ＞ button\f and pre\f\f t\be ◉OK button.
2.  You can \fee t\be current information of t\be projector.
• Pre\f\f t\be BACK button to exit t\be menu \fcreen.
To See T\be Projector Information
1.  
Pre\f\f t\be MENU button. T\ben, move to OPTION wit\b t\be 
∧, ∨, ＜, ＞ button\f and pre\f\f t\be ◉OK button.
2.   
Pre\f\f t\be ∧, ∨ button\f to move to Demo Mode and pre\f\f 
t\be ◉OK button.
3.  
Pre\f\f t\be ∧, ∨ button\f to move to On and pre\f\f t\be 
◉OK button.
• It can be \felected w\ben Initial Setting i\f \fet a\f Store Demo.
• Pre\f\f t\be BACK button to exit t\be menu \fcreen.
1.  
Pre\f\f t\be MENU button. T\ben, move to OPTION wit\b t\be 
∧, ∨, ＜, ＞  button\f and pre\f\f t\be ◉OK button.
2.  
Pre\f\f t\be ∧, ∨ button\f to move to Initial Setting and 
pre\f\f t\be ◉OK button.
3.  
Move to a de\fired item wit\b t\be ∧, ∨ button\f and t\ben 
pre\f\f t\be ◉OK button.
• Set a\f Home U\fe w\ben u\fed in \bome\f.
• Pre\f\f t\be BACK button to exit t\be menu \fcreen.
OPTION
Menu Language  : Engli\fhBlank Image  : BlueScreen CaptureLED Mode   : NormalAuto Power  : OffDemo Mode  : OffInitial Setting  : Store Demo
OPTION
Menu Language  : Engli\fhBlank Image  : BlueScreen CaptureLED Mode   : NormalAuto Power  : OffDemo Mode  : OffInitial Setting  : Home U\fe
INFORMATION
Model Name  : HX300Input  : RGBRe\folution  : 1024 x 768Fh/Fv  : 48.36 Khz/60 Hz
ꔂMove   ꔉOK
ꔂMove   ꔉOK
Initial Setting Function
Demo Mode Function  
						

							USB
30
*  
W\ben you connect a USB device, t\bi\f \fcreen i\f di\fplayed, automatically.In USB device, you can not add a new folder or delete t\be exi\fting folder.
USB
To u\fe the USB device
*   
Image \f\bown may differ from your projector.
Connecting t\be USB device
1.  
Connect t\be USB device to t\be USB jack on t\be back of t\be \fet. 
2.  It turn\f automatically to DivX Home Menu.
* Select “Eject” in order to eject a USB device.
Eject USB
USB memory \ftickPHOTO LISTMUSIC LISTMOVIE LISTFILE VIEWER
1. Pre\f\f t\be Q.MENU button on t\be remote control.
2.   
Pre\f\f t\be ＜, ＞ button\f to move to USB Device.
3. Pre\f\f t\be ◉OK button on t\be remote control.
•  
After Eject USB, USB memory cannot be read. Remove USB memory, and connect again.
• Pre\f\f t\be BACK button to exit t\be menu \fcreen.
USB Device
Eject ꔉ