LG Hs200 Projector User Manual

							Function22
1.  
Press the  MENU button. Then, move to  SCREEN with the ∧, ∨ , ＜ , ＞   
buttons and press the  ◉OK  button.
2.   
Press the  ∧, ∨  buttons to move to  RGB Config. and press the  ◉OK   
button.
3.  Move to a desired item with the  ∧, ∨  buttons and then press the  ＞ button.
4.   
Press the  ∧, ∨ , ＜ , ＞  button to adjust the screen condition as you want 
and then press the  ◉OK  button.
•   
Resolution  can be chosen between 768 resolution 
(1024x768/1280x768/1360x768, 60Hz) and 1050 resolution 
(1400x1050/1680x1050, 60Hz).
•   To exit the menu display, press the  RETURN button.
RGB Config. Function
1. Press the  STILL button on the remote control. * You can freeze the moving image.
2. To exit STILL, press any button. * The STILL function will release automatically after approximately 10 minutes.
Using the Still Function
 
RGB Config.
Auto Configure
Position
Resolution        
ꔃ
Size
Phase
Reset
ꔓ 1024 x 768
  1280 x 768
  1360 x 768
     Press the  AUTO button of the remote control.
•    If you execute screen adjustment for a video from PC graphic signal, optimal state 
may not be found. Execute the  Auto Configure function for a still image.
•  You can use this function through the  MENU button.
Auto Configure Function
*    This function assures you of getting the best video quality by automatically adjusting the horizontal size and synchronization 
of the image. 
*   Auto Tracking function works in RGB PC input only.
Auto configure
ꔂMove    ꘀ Prev.  
						

							Function
23
AUDIO Menu Options
FM Wireless Audio is a function to send out audio signals from the projector using FM frequency (88.5 ~95.5 MHz).
The frequency of Projector and FM receiver should be same in order to output the sound from FM receiver normally.
The signal can be received by using FM receiver within 3m of distance.
What is FM Wireless Audio? (HS200/HS200G only)
< The recommended use range of FM receiver >
Install projector and FM receiver without any abstacles as shown on the figure below.
A FM receiver can be reached 5 m when the antenna length and direction are good.
< The recommended length of FM receiver Antenna >
We recommend to use a rod antenna 0.8 ~ 1.5 m for better sound quality since audio noise can be detected when 
using under 0.8m rod antenna.Audio Signal 88.5 ~95.5 MHz
Receiving range
Within 3mFM Receiver
Projector Front
45°
45°
45° 45°  
						

							Function24
• This product is for domestic use.
•   
If used in a medical institution, it may cause an error for medical equipments.Please do not use in a medical 
establishment.
•    Please maintain the distance between the projector and FM receiver within 3m.
•   
The sound from FM receiver may not come out in the desired quality if the distance is more than 3m.
•   
Please adjust the location of FM receiver and its antenna and install them to where it shows a good condition 
of receiving reception.
•    According to the installed location and environment, the receiving distance may become shorter and the 
sound may be interrupted due to:
    - If an obstacle is located near the projector and FM receiver.
    - If an obstacle passes near by the projector and FM receiver.
    - If the FM receiver is installed Left, Right, or diagonal line of projector
    - If the Projector or the FM receiver is located inside of a rack made of metal.
    - If other FM transmitter equipment is working near at the same frequency.
    - If there is a radio broadcast on air at the same frequency.
    - If working in the dusty, humid, or high temperature environment.
Installing Instructions (HS200/HS200G Only)
• Please adjust the antenna of FM receiver or move the location of FM receiver.
•    If there is no Audio signal or low reception, within 55 seconds the FM Wireless Audio function will shut down 
automatically.
•    Please check the incoming audio signal.
•  Please check if the power of projector or FM receiver is on.
•  Please check if there is any obstacle between the projector and FM receiver.
•  Please check if there is any metallic hardware or electronic product near by.
•  Please check if there is any radio broadcasting channel using the same frequency.
•    
If there is a radio broadcasting channel using the same frequency, please change to a different frequency on 
the projector.
What do I do if the FM receiving signal is not good? (HS200/HS200G Only)  
						

							Function
25
To listen through the FM receiver speaker (HS200/HS200G Only)
Adjusting Volume
   Press the VOLUME +, - button on the remote control.
• If FM Wireless Audio is  on, it does not function. Adjust with FM receiver.
•  You can use this function through the  MENU button.
AUDIO
FM Wireless Audio : Off
  • Frequency   88.5 MHz
Volume       50
Balance       0
Treble       0
LR
1.   Press the  MENU button. Then, move to  AUDIO with the  ∧, ∨ , ＜ , ＞ 
buttons and press the  ◉OK  button.
2.   
Press the  ∧, ∨  buttons to move to  FM Wireless Audio  and press the 
◉ OK  button.
3.   
Press the  ∧, ∨  buttons to move to  On and press the  ◉OK  button.
4.   
Press the  ∧, ∨  buttons to move to  Frequency and press the  ◉OK 
button.
5.   
Press the  ＜, ＞  buttons to adjusting frequency  and press the  ◉OK  button.
6.  Set the frequency of FM receiver to the frequency of the set projector.
•   
Setting  FM Wireless Audio as  on disables mute/volume/balance/ treble functions.
•   
There may be differences in the reception distance and the audio quality according to the type of FM receiver and 
installation locations.
•  FM frequency can be set between 88.5 ~95.5 MHz.
•    If you don’t use the FM receiver or audio signals from the projector,  off should be selected.
•   
When power is back on, it is changed to  off status.
•  Press the  MENU or RETURN button to exit the menu screen.
ꔂMove    ꔉOK  
						

							Function26
Adjusting Speaker Balance
Adjusting Treble
AUDIO
FM Wireless Audio  : Off
  • Frequency   88.5 MHz
Volume       50
Balance       0
Treble       0
LR
AUDIO
FM Wireless Audio  : Off
  • Frequency   88.5 MHz
Volume       50
Balance       0
Treble       0
LR
1.  
Press the  MENU button. Then, move to  AUDIO with the  ∧, ∨ , ＜ , ＞ 
buttons and press the  ◉OK  button.
2.   
Press the  ∧, ∨  buttons to move to  Treble and press the  ◉OK  button.
3.   
Press the  ＜, ＞  buttons to adjusting audio treble  and press the  ◉OK 
button.
•   If FM Wireless Audio is  on, it does not function. Adjust with FM receiver.
•   Press the  MENU or RETURN button to exit the menu screen.
* Adjust the treble your taste and room situations.  * Adjust the left/right sound of speaker to suit your taste and room situations.
1.
   Press the  MENU button. Then, move to  AUDIO with the  ∧, ∨ , ＜ , ＞ 
buttons and press the  ◉OK  button.
2.   
Press the  ∧, ∨  buttons to move to  Balance and press the  ◉OK 
button.
3.   
Press the  ＜, ＞  buttons to adjusting audio balance  and press the 
◉ OK  button.
• If FM Wireless Audio is  on, it does not function. Adjust with FM receiver.
•  Press the  MENU or RETURN button to exit the menu screen.
ꔂMove    ꔉOK
ꔂMove    ꔉOK  
						

							Function
27 * The sleep timer turns the projector off at the preset time.
1. Press the  Q.MENU button on the remote control.
2.    Press the  ∧, ∨  buttons to move to  Sleep Timer.
3.  Press the  ＜, ＞  buttons to select a desired preset time.
•  You can use this function through the  MENU button.
•  To exit the menu display, press the  RETURN button.
Sleep time Function
Auto Off Function
TIME Menu Options
1.  
Press the  MENU button. Then, move to  TIME with the  ∧, ∨ , ＜ , ＞ 
buttons and press the  ◉OK  button.
2.   
Press the  ∧, ∨  buttons to move to  Auto Off and press the  ◉OK 
button.
3.   
Move to  On with the  ∧, ∨  buttons and then press the  ◉OK  button.
• Press the  MENU or RETURN button to exit the menu screen.
* 
 
This function turns the projector off automatically after 10 minutes is passed when there is no signal.
◄ Off  ►◄ 10 Min.  ►◄ 20 Min. ►◄ 30 Min. ►
◄ 240 Min.  ►◄ 180 Min. ►◄ 120 Min. ►◄ 90 Min. ►
◄ 60 Min. ►
Q-Menu
Close
16:9
Vivid
◄ Off ►
Eject
Aspect Ratio
Picture Mode
Sleep Timer
Eject USB
TIME
Sleep Timer  : Off
Auto Off  : Off
OPTION Menu Options
1.   Press the  MENU button. Then, move to  OPTION with the  ∧, ∨ , ＜ , ＞ 
buttons and press the  ◉OK  button.
2.   
Press the  ∧, ∨  buttons to move to  Menu Language and press the 
◉ OK  button.
3.   
Move to a desired item with the  ∧, ∨ , ＜ , ＞  buttons and then press the 
◉ OK  button.
• On-Screen-Display (OSD) is displayed in the selected language.
•  Press the  MENU or RETURN button to exit the menu screen.
Selecting Language
OPTION
Menu Language  : English
Blank Image  : Black
Screen Capture
LED Mode  : Normal
Auto Power  : Off
Keypad LED  : On
Demo Mode  : Off
Initial Setting  : Home Use
ꔂMove    ꔉOK
ꔂMove    ꔉOK  
						

							Function28
1. Press the  BLANK button on the remote control.
• The screen turns off to a background color.
•  You can choose the background color.
    (Refer to ‘Selecting Blank image’)
2. Press any button to cancel the blank function.
•   
To temporarily turn off the lamp, press  BLANK on the remote control. Do not block the projection lens with any objects 
when the projector is under operation as this could cause the objects to become heated and deformed or even cause a fire. 
Using Blank Function
* This function may be effective if you need to get the attention of the audience during presentations, meetings or briefings.
1.   
Press the  MENU button. Then, move to  OPTION with the  ∧, ∨ , ＜ , ＞ 
buttons and press the  ◉OK  button.
2.   
Press the  ∧, ∨  buttons to move to  Blank Image and press the  ◉OK 
button.
3.   
Move to a desired item with the  ＜, ＞  buttons and then press the  ◉OK 
button.
•  Background image will be altered to the selected Blank function image.
•  Press the  MENU or RETURN button to exit the menu screen.
Selecting Blank image
OPTION
Menu Language  : English
Blank Image  : Black
Screen Capture
LED Mode  : Normal
Auto Power  : Off
Keypad LED  : On
Demo Mode  : Off
Initial Setting  : Home Use
1.   Press the  MENU button. Then, move to  OPTION with the  ∧, ∨ , ＜ , ＞ 
buttons and press the  ◉OK  button.
2.   
Press the  ∧, ∨  buttons to move to  Screen Capture and press the 
◉ OK  button.
• It can only be elected when there is an input signal.
•  It takes up to 2 minutes when capturing screen.
•  Press the  MENU or RETURN button to exit the menu screen.
Screen Capture Function
OPTION
Menu Language  : English
Blank Image  : Black
Screen Capture
LED Mode  : Normal
Auto Power  : Off
Keypad LED  : On
Demo Mode  : Off
Initial Setting  : Home Use
ꔂMove    ꔉOK
ꔂMove    ꔉOK  
						

							Function
29
1.   Press the  MENU button. Then, move to  OPTION with the  ∧, ∨ , ＜ , ＞  
buttons and press the  ◉OK  button.
2.   
Press the  ∧, ∨  buttons to move to  Auto Power and press the  ◉OK 
button.
3.   
Press the  ∧, ∨  buttons to move to  On and press the  ◉OK  button.
• On: Connecting DC cable to the projector turns on the projector.
•  Off:   
Connecting DC cable to the projector makes the projector in standby 
state.
•  Press the  MENU or RETURN button to exit the menu screen.
To make the power of the projector turn on automatically when power is in
OPTION
Menu Language  : English
Blank Image  : Black
Screen Capture
LED Mode  : Normal
Auto Power  : Off
Keypad LED  : On
Demo Mode  : Off
Initial Setting  : Home Use
1.   Press the  MENU button. Then, move to  OPTION with the  ∧, ∨ , ＜ , ＞ 
buttons and press the  ◉OK  button.
2.   
Press the  ∧, ∨  buttons to move to  LED Mode and press the  ◉OK 
button.
3.   
Move to a desired item with the  ∧, ∨  buttons and then press the  ◉OK 
button.
•   
LED Mode changes into Dimming mode automatically at specific tempera-
tures (95°F (35°C) or higher). 
•  Dimming mode gets about 90% brightness of original led mode.
•  Press the  MENU or RETURN button to exit the menu screen.
To adjust the brightness of the screen
OPTION
Menu Language  : English
Blank Image  : Black
Screen Capture
LED Mode  : Normal
Auto Power  : Off
Keypad LED  : On
Demo Mode  : Off
Initial Setting  : Home Use
To set the button light
1.   Press the  MENU button. Then, move to  OPTION with the  ∧, ∨ , ＜ , ＞  
buttons and press the  ◉OK  button.
2.   
Press the  ∧, ∨  buttons to move to  Keypad LED and press the  ◉OK 
button.
3.   
Press the  ∧, ∨  buttons to move to  On and press the  ◉OK  button.
• On: When button is pressed, it lights for 5 seconds before turning off.
•  Off:   
The lights on the buttons do not turn on.
•  Press the  MENU or RETURN button to exit the menu screen.
OPTION
Menu Language  : English
Blank Image  : Black
Screen Capture
LED Mode  : Normal
Auto Power  : Off
Keypad LED  : On
Demo Mode  : Off
Initial Setting  : Home Use
ꔂMove    ꔉOK
ꔂMove   
ꔉOK
ꔂMove    ꔉOK  
						

							Function30
Demo Mode Function
Initial Setting Function
INFORMATION Menu Options
1.  
Press the  MENU button. Then, move to  INFORMATION with 
the  ∧, ∨ , ＜ , ＞  buttons and press the  ◉OK  button.
2.  You can see the current information of the projector.
•  Press the  MENU or RETURN button to exit the menu screen.
To See The Projector Information
1.  
Press the  MENU button. Then, move to  OPTION with the  ∧, ∨ , ＜ , ＞ 
buttons and press the  ◉OK  button.
2.   
Press the  ∧, ∨  buttons to move to  Demo Mode and press the  ◉OK 
button.
3.   
Press the  ∧, ∨  buttons to move to  On and press the  ◉OK button.
• It can be selected when  Initial Setting is set as Store Demo.
•  Press the  MENU or RETURN button to exit the menu screen.
1.  
Press the  MENU button. Then, move to  OPTION with the  ∧, ∨ , ＜ , ＞  
buttons and press the  ◉OK  button.
2.   
Press the  ∧, ∨  buttons to move to  Initial Setting and press the ◉OK 
button.
3.   
Move to a desired item with the  ∧, ∨  buttons and then press the  ◉OK 
button.
•  Set as  Home Use when used in homes.
•  Press the  MENU or RETURN button to exit the menu screen.
OPTION
Menu Language  : English
Blank Image  : Black
Screen Capture
LED Mode  : Normal
Auto Power  : Off
Keypad LED  : On
Demo Mode  : Off
Initial Setting  : Store Demo
OPTION
Menu Language  : English
Blank Image  : Black
Screen Capture
LED Mode  : Normal
Auto Power  : Off
Keypad LED  : On
Demo Mode  : Off
Initial Setting  : Home Use
INFORMATION
Model Name  : HS200-JE
Input   : Video
Resolution  : NTSC M
Fh/Fv   : 15.7KHz/60.0Hz
ꔂMove   ꔉOK
ꔂMove    ꔉOK  
						

							Q-Menu
Close
16:9
Off
Aspect Ratio
Picture Mode
Sleep Timer
Eject USB
USB
31 *   When you connect a USB device, this screen is displayed, automatically.
  In USB device, you can not add a new folder or delete the existing folder.
 
►   
Only a USB storage device is recognizable. Digital camera and mobile phone are not supported.
 
►  
If the USB storage device is connected through a USB hub, the device is not recognizable.
 
►   
A USB storage device using an automatic recognition programmed may not be recognized.
 
►   
A USB storage device which uses its own driver may not be recognized.
 
►   
The recognition speed of a USB storage device may depend on each device.
 
►   
Please do not turn off the projector or unplug the USB device when the connected USB storage device is working.  When 
such device is suddenly separated or unplugged, the stored files or the USB storage device may be damaged.
 
►   Please do not connect the USB storage device which was artificially maneuvered on the PC. The device may cause the 
product to malfunction or fail to be played.  Never forget to use only a USB storage device which has normal music files or 
image files.
 
►   Please use only a USB storage device which was formatted as a FAT16, FAT32 and NTFS file system provided with the 
Windows operating system. In case of a storage device formatted as a different utility programmed which is not supported 
by Windows, it may not be recognized.
 
►   Please connect power to a USB storage device which requires an external power supply.  If not, the device may not be 
recognized.
 
►   Please connect a USB storage device with cable is offered by USB maker.  If connected with cable is not offered by USB 
maker or an excessively long cable, the device may not be recognized.
 
►   Some USB storage devices may not be supported or operated smoothly.
 
► If the name of a folder or file is too long, it will not be displayed or recognized.
 
►  
File alignment method is based on storage order in USB storage device.
 
►  
Please backup the important file because a data of USB device may be damaged. Data management is consumer's 
responsibility and in consequence the manufactures does not cover the product bearing data damage. 
 
►   If the quantity of folders and files is over 1,000, it will not be displayed or recognized about exceeded files and folders.
 
►  
It is supported for only primary partition. If there is an extended partition, it is not displayed or recognized.
 
►  
The recommended capacity is 1TB or less for a USB external hard disk and 32GB or less for USB memory. Any device 
with more than the recommended capacity may not work properly.
 
► Data in a USB storage device cannot be deleted in the NTFS file system.
 
► If the USB memory device does not work properly, disconnect and reconnect it.
 
►   If a USB external hard disk with a "Energy Saving"function does not work, turn the hard disk off and on again to make it 
work properly.
 
► USB storage devices below USB 2.0 are supported as well.But they may not work properly in the movie list.
USB
To use the USB device
*   Image shown may differ from your projector.
Connecting the USB device
1.   
Connect the USB device to the USB jack on the back of the set. 
2.  It turns automatically to DivX Home Menu.
* Select “Eject” in order to eject a USB device.
Eject USB
Precautions when using the USB device
USB memory stickPHOTO LISTMUSIC LIST MOVIE LIST
Vivid
Eject
1.
 Press the  Q.MENU button on the remote control.
2.   
Press the  ∧, ∨  buttons to move to  Eject USB.
3.  Press the  ◉OK  button on the remote control.
•  
After  Eject USB, USB memory cannot be read. Remove USB memory, 
and connect again.
•  To exit the menu display, press the  RETURN button.