LG Hs102g Projector User Manual

Installing and Composition
11
Installing and Composition
Provide proper ventilation for this projector.
The projector is equipped with ventilationholes(intake)
on the bottom and ventilation holes(exhaust) on the front.
Do not block or place anything near these holes, or inter-
nal heat build-up may occur, causing picture degradation
or damage to the projector.
Place this projector in adequate temperature and humidity conditions.
Install this projector only in a location where adequate temperature and...

Installing and Composition
12
* You can install this projector using a tripod for the camera. You can assemble the projector  instead of the camera
on camera tripod.
How to install the projector using the tripod
Camera Tripod Part connected to the tripod
- If you have a camera tripod, assemble the projector to the part connecting to the camera tripod
Finished condition when projector is install on the tripodPart connected to the projector
Bottom side of Projector 

Installing and Composition
13
1. Place the projector on a sturdy and horizontal surface with the PC or AV source.
2. Place the projector with the desired distance from the screen. The distance between the projector and the screen
determines the actual size of the image. 
3. Position the projector so that the lens is set at a right angle to the screen. If the projector is not set at a right angle, the
screen image will be crooked. If this is so then the keystone adjustment may correct this (Refer to page...

Installing and Composition
14
The projector has a ‘Kensington’Security System Connector on the side panel. Connect the ‘Kensington’
Security System cable as below.
For the detailed installation and use of the Kensington Security System, refer to the user’s guide attached
to the Kensington Security System set. 
And for further information, contact http://www.kensington.com, the internet homepage of the
Kensington company that deals with expensive electronic equipment such as notebook PCs or projec-...

Installing and Composition
15
Turning on the Projector
1. Connect power cord correctly.
2. Press the  button on the top cover or the POWER button on the remote control.(The light on the control
panel will be turned on.)
Press the SOURCE button on the remote control or the SOURCE button on the control panel to select the input signal you want.When you press the POWER button on the remote control or the       button on the control panel when you turn on the projector, the
lights for all buttons on the...

Installing and Composition
16
RGBSelect                   OK
When an image appears on the screen, check if it is in focus and fits well to the screen.
To adjust the focus of the image, rotate the focus ring which is the outer ring on the lens.
Focus ring
Focus and Position of the Screen Image
Selecting source mode
1. Press the SOURCEbutton on the top cover or remote control.
RGBVideo
2. Each press of the,button changes the display as below.
When you connect the RGB to Component cable to the RGB IN...

Connection
17
Connection
Connecting to a Desktop PC
* You can connect the projector to a computer of VGA, SVGA, XGA and SXGA output. 
* Refer to page 39 for the supported monitor displays of the projector.
< How to connect >
Connect computer cable to RGB IN (PC/DTV)of the projector.
Connecting to a Notebook PC
< How to connect >
Connect computer cable to RGB IN (PC/DTV)of the 
projector.
* If you set your computer to output the signal to both the
display of your computer and the external projector, the...

Connection
18
Connecting to a DVD
< How to connect >
a. After connecting the Component cable of DVD to the RGB
to Component cable, connect it to the RGB IN(PC/DTV)
terminal of the projector.  
* When connecting the component cable, match the jack colors
with the component cable.(Y=green, PB=blue, PR=red)PRPBY(R) AUDIO (L) 
* The output jacks (Y, PB, PR) of the DVD might be labelled as Y, Pb, Pr / Y, B-Y, R-Y / Y, Cb, Cr according to the equipment.

Component cable
Connecting to a D-TV Set-Top Box
< How...

Function
19
Function
Video Menu Options
* In this manual, the OSD(On Screen Display) may be different from your Projector’s because it is just an example to
help with the Projector operation.
* This operating guide explains operation of RGB(PC) mode mainly.
1. Press the MENUbutton and then use ,button to select the  menu.
2. Press the 
,button to select a video item you want to adjust.
3. Press the 
,button to adjust the screen condition as you want.
< RGB mode >
< Video mode >
Each adjustment of...

Function
20
Picture mode
* Use Picture mode function to set the projector for the best picture appearance.
* This function does not work in RGB or DivX mode.
Picture mode
Contrast               80
Brightness            50
Color                    50
Sharpness            50
Tint                                0Clear
1. Press the MENUbutton and then use ,button to select the         menu.
2. Press the  
,button to selectPicture modeitem.
3. Press the 
,button to adjust the screen condition as you want....