LG Hs102 Projector User Manual

							Installing and Composition
11
Installing and Composition
Provide proper ventilation for this projector.
The projector is equipped with ventilationholes(intake)
on the bottom and ventilation holes(exhaust) on the front.
Do not block or place anything near these holes, or inter-
nal heat build-up may occur, causing picture degradation
or damage to the projector.
Place this projector in adequate temperature and humidity conditions.
Install this projector only in a location where adequate temperature and humidity is available. (refer p.41)
Do not place the projector on a carpet, rug or other
similar surface. It may prevent a adequate ventilation
of the projector bottom. This product should be
mounted to a wall or ceiling only.
*Don’t place the projector in the following conditions. It may cause malfunction or product damage.

Never push projector or spill any kind of liquid into the
projector.Leave an adequate distance(30cm/12 inches or
more) around the projector.
Don’t place the projector where it can be covered with dust.
This may cause overheating of the projector.
Do not obstruct the slots and openings of the projector. This may cause overheating and create a fire
hazard.
The projector is manufactured using high-precision technology. You may, however, see tiny black points
and/or bright points (red, blue, or green) that continuously appear on the projector Screen. This is a nor-
mal result of the manufacturing process and does not indicate a malfunction.
To display DTV programs, it is necessary to purchase a DTV receiver (Set-top Box) and connect it to the
projector.
Installation Instructions
When the remote control does not work during operation.
The remote control may not work when a lamp equipped with electronic ballast or a three-wavelength lamp is installed.
Replace those lamps with international standard products to use the remote control normally. 
						

							Installing and Composition
12
* You can install this projector using a tripod for the camera. You can assemble the projector  instead of the camera
on camera tripod.
How to install the projector using the tripod
Camera Tripod Part connected to the tripod
- If you have a camera tripod, assemble the projector to the part connecting to the camera tripod
Finished condition when projector is install on the tripodPart connected to the projector
Bottom side of Projector 
						

							Installing and Composition
13
1. Place the projector on a sturdy and horizontal surface with the PC or AV source.
2. Place the projector with the desired distance from the screen. The distance between the projector and the screen
determines the actual size of the image. 
3. Position the projector so that the lens is set at a right angle to the screen. If the projector is not set at a right angle, the
screen image will be crooked. If this is so then the keystone adjustment may correct this (Refer to page 27.).
4. Connect the cables of the projector to a wall power socket and other connected sources.
projection distance based on the picture format
Projection distance (D)Projection off-set ratio:100%
43mm
Projection distance (D)
Basic Operation of the Projector
Screen
Screen height (X)
X/2
X/2
Y/2
Y/2
Screen
Screen Width (Y)
4 : 3 Scale
Projection Distance(D)
(mm)Diagonal Size
(inch)Diagonal Size
(mm)Horizontal Size
(mm)Vertical Size
(mm) 
						

							Installing and Composition
14
The projector has a ‘Kensington’Security System Connector on the side panel. Connect the ‘Kensington’
Security System cable as below.
For the detailed installation and use of the Kensington Security System, refer to the user’s guide attached
to the Kensington Security System set. 
And for further information, contact http://www.kensington.com, the internet homepage of the
Kensington company that deals with expensive electronic equipment such as notebook PCs or projec-
tors.
 Kensington Security System is an optional item.
Using Kensington Security System 
						

							Installing and Composition
15
Turning on the Projector
1. Connect power cord correctly.
2. Press the  button on the top cover or the POWER button on the remote control.(The light on the control
panel will be turned on.)
Press the SOURCE button on the remote control or the SOURCE button on the control panel to select the input signal you want.When you press the POWER button on the remote control or the       button on the control panel when you turn on the projector, the
lights for all buttons on the control panel will be turned on.
Turning off the Projector
1. Press the  button on the top cover or the POWER button on the remote control.
2. Press the  button on the top cover or the POWER button on the remote control again to turn off the
power.
When you press POWER button when you turn off the projector, the lights for all buttons on the control panel will be turned off. When
you press any button on the control panel when the projector is turned off, the light only on the POWER LED turned on. (When the
POWER cord is connected.)
Power off? 
Please press Power key again. 
						

							Installing and Composition
16
RGBSelect                   OK
When an image appears on the screen, check if it is in focus and fits well to the screen.
To adjust the focus of the image, rotate the focus ring which is the outer ring on the lens.
Focus ring
Focus and Position of the Screen Image
Selecting source mode
1. Press the SOURCEbutton on the top cover or remote control.
RGBVideo
2. Each press of the,button changes the display as below.
When you connect the RGB to Component cable to the RGB IN (PC/DTV) terminal and select RGB input, you can receive the Component input. DivX mode runs automatically when connects USB device. 
						

							Connection
17
Connection
Connecting to a Desktop PC
* You can connect the projector to a computer of VGA, SVGA, XGA and SXGA output. 
* Refer to page 39 for the supported monitor displays of the projector.
< How to connect >
Connect computer cable to RGB IN (PC/DTV)of the projector.
Connecting to a Notebook PC
< How to connect >
Connect computer cable to RGB IN (PC/DTV)of the 
projector.
* If you set your computer to output the signal to both the
display of your computer and the external projector, the
picture of the external projector may not appear properly.
In such cases, set the output mode of your computer to
output the signal only to the external projector. For
details, refer to the operating instructions supplied with
your computer.
Connecting to a Video Source
< How to connect  >
a. Connect the A/V INjack of the projector to the output jacks
of the A/V source with A/V cable. 
S VIDEO
(R) AUDIO (L)       V I D E O
OUT
IN
* You can connect a VTR, a camcorder or any other compatible video image source to the projector.
 
						

							Connection
18
Connecting to a DVD
< How to connect >
a. After connecting the Component cable of DVD to the RGB
to Component cable, connect it to the RGB IN(PC/DTV)
terminal of the projector.  
* When connecting the component cable, match the jack colors
with the component cable.(Y=green, PB=blue, PR=red)PRPBY(R) AUDIO (L) 
* The output jacks (Y, PB, PR) of the DVD might be labelled as Y, Pb, Pr / Y, B-Y, R-Y / Y, Cb, Cr according to the equipment.

Component cable
Connecting to a D-TV Set-Top Box
< How to connect an RGB source >
a. Connect RGB cable to RGB IN (PC/DTV)of the 
projector.
b. Use a DTV receiver with DTV 480p(576p)/720p/1080i mode.
(R) AUDIO (L) DTV OUTPUTDVI OUTPUTPRPBYHDMI OUTPUT
* To receive D-TV programmes, it is necessary to purchase a D-TV receiver (Set-Top Box) and connect it to the projector. 
* Please refer to the owners manual of the D-TV Set-Top Box for the connection between projector and D-TV Set-Top Box.

Component cable
< How to connect a Component source >
a. Connect the D-TV Set-Top Box Component cable with RGB
to Component cable and than connect it to RGB
IN(PC/DTV) of the projector.   
* When connecting the component cable, match the jack colors 
with the component cable.(Y=green, PB=blue, PR=red)
b. Use a DTV receiver with DTV 480p(576p)/720p/1080i mode.
(R) AUDIO (L) DTV OUTPUTDVI OUTPUTPRPBYHDMI OUTPUT
Signal
480i
480p
720p
1080i
576i
576pComponent
O
O
O
O
O
ORGB/DTV
X
O
O
O
X
O

RGB to Component Cable
RGB to Component Cable 
						

							Function
19
Function
Video Menu Options
* In this manual, the OSD(On Screen Display) may be different from your Projector’s because it is just an example to
help with the Projector operation.
* This operating guide explains operation of RGB(PC) mode mainly.
1. Press the MENUbutton and then use ,button to select the  menu.
2. Press the 
,button to select a video item you want to adjust.
3. Press the 
,button to adjust the screen condition as you want.
< RGB mode >
< Video mode >
Each adjustment of       menu options will not affect other inputs. 
As required, re-adjust        menu options for the input sources.
To restore the original image condition after changing it, press OKbutton 
after selecting [Reset] item.
When receiving an NTSC signal, the picture item Tintis displayed and can 
be adjusted.(60Hz only)
 You can use this function through the  button on the control panel.Press the MENUbutton twice or the RETURNbutton to exit the menu screen.
Adjusting Video 
Picture mode
Contrast               80
Brightness            50
Color                    50
Sharpness            50
Tint                                0Clear
Contrast 50
Brightness            50
Color R                50
Color G                50
Color B                50
Reset
MENU Exit              Move          OK
MENU Exit              Move          OK
< DivX mode >
Contrast               80
Brightness            50
Sharpness            50
Reset                               
MENU Exit              Move          OK 
						

							Function
20
Picture mode
* Use Picture mode function to set the projector for the best picture appearance.
* This function does not work in RGB or DivX mode.
Picture mode
Contrast               80
Brightness            50
Color                    50
Sharpness            50
Tint                                0Clear
1. Press the MENUbutton and then use ,button to select the         menu.
2. Press the  
,button to selectPicture modeitem.
3. Press the 
,button to adjust the screen condition as you want.
Each press of the,button changes the screen as shown below.
 You can use this function through the  button on the control panel. Press the MENUbutton twice or the RETURNbutton to exit the menu screen. Clear
SoftUser
MENU Prev.        Move            Select
1. Press the MENUbutton and then use ,button to select the         menu.
2. Press the  
,button to selectColor temp.item.
3. Press the 
,button to make desired adjustments.
Color Temperature Control
Each press of the , button changes the screen as shown below.
 You can use this function through the  button on the control panel. Press the MENUbutton twice or the RETURNbutton to exit the menu screen. Normal
WarmCool
Color temp.
Smart picture
Black level
Keypad Sound
Keypad LED
Screen CaptureNormal
Normal
High
MENU Prev.        Move            Select
On
On