LG Gw C207 Flqa Owners Manual

							9
Door replacement
Installation
3) Remove the freezer compartment door by lifting it upward. The door should be \glifted high enough for the feed water pipe tube to be completely pulled out.
1) Loosen the hinge cover screws and remove the cover. Remove  connection wires, if any, except for the earth line.
2) Remove keeper by rotating it  clockwise (   ) and the\gn remove the upper hinge by lifting it up (   ).
3) Remove the refrigerator  compartment door by lifting it up.
Pass the refrigerator laterally through the access door as illust\grated to the right.
Once the fridge is through the access door, remount the fridge doors by following the door removal instructions in reverse.
Remove the
re\brigerator
compartment
door
Pass the 
re\brigerator 
Lower cover
 Eno\fgh \bor  water \beed pipe t\fbe to be completly p\flled o\ft
\bOTE• If you have removed the refrigerator compartment door to pass the applian\gce  through an access door, lay the door down, but be careful not to damage the feed water pipe tube.
Connectionwires
Upper hingeKeeper
Lower hinge
①②
Installation
\bOTE• If a tube end is de\gformed or abraded, trim the end with sharp knife until perfectly round.
ENGLISH
ENGLISH
 
						

							1010
Installation
Feed water pipe installation (Dispenser mo\gdel only)
Height adjustment
Installation
▪Automatic ice maker operation needs water pressure of 147~834kPa (1.5~8.5kgf/cm2) (The pressure is correct when an instant paper cup (180cc) is filled in 3 sec.).▪If water pressure does not reach the rating 147kPa(1.5kgf/cm2) or below, it is necessary to purchase a separate pressure pump for normal automatic icing and cool water feed.▪Keep the total length of the \gfeed water pipe tube withi\gn 8m and be careful that the tube does not \gbend. If the tube is 8m o\gr longer it may cause water feed problems owing to the drain water pressure.▪Install the feed water pipe tube at a place free from heat.▪Connect to drinking water supply only.▪Refer to instructions with water filter kit for installation.
Level the door by inserting flat( - type) driver into the groove of the left height adjusting screw and rotate it clockwise (   ).
Level the door by inserting flat( - type) driver into the groove of the left height adjusting screw and rotate it clockwise (   ).
Be\bore  
installation
I\b the \breezer  
compartment 
door is lower than 
the re\brigerator  
compartment 
door
I\b the \breezer  
compartment 
door is higher than 
the  re\brigerator  
compartment 
door
Height difference
Height difference
Heightdifference
Heightdifference
Left height  adjustment screw
Right height  adjustment screw
Warning
①
①
ENGLISH
 
						

							11
Installation
The refrigerator doors will clos\ge smoothly by adjusting the front side using the 
height adjustment screw. If the doors do not\g close correctly, performance may be 
affected.
1. Wipe off all dust ac\gcumulated during shipping and cl\gean your appliance  
thoroughly.
2. Install accessories such as the ic\ge cube box, cover evaporating tray, etc., in their
proper places. They are packed together to prevent possible damage d\guring ship -
ping.
3. Connect the power supply cord (or plug) to the outlet. Don’t double up with  other appliances on the same out\glet.A\bter levelling 
the door height
Next
Installation
ENGLISH
ENGLISH
- Disassemble and empty the automatic icemaker.
- Turn of the ice maker ( 
).
- Assemble the Door rack with care.
Insert into bottom hole ( ).
Don’t store any food easily fallen. It might fall to the foor 
when you open the door.
Usage of  
door rack
(option)
2
3
1
Use more space with door rack when you don’t use Ice Maker.
 
						

							1212
Express freezer. Child  lock : Hol d3 secs .
Display  Saving  Mode
Display  Saving  Mode
Display  Saving  Mode
Te mpe rature  adjus tme nt  button
for fr eezer c ompartment .Tempe rature  adjus tme nt  button
For r efrigerat or comp artme nt.
Function display board
Optional
Type-1
Type-2
Type-3
NOTE
• Your model may not include every option.
• Display Type - 3: The contr ol display is operated by touch. Exc essive moisture on the 
display panel ma y cause a malfunction. P lease keep the display panel clean and dry.
Starting
Adjusting the temperatur e and functions
Operation
When your r efrigerator is first installed, allow it t o stabilize at normal operating
temperatur es for 2-3 hours prior t o filling it with fresh or frozen foods.
I f opera tion is interrupted, wait 5 minut es before restarting.
*Non dispenser model - Type 1
ENGLISH
 
						

							13
Display Power Saving Mode
Operation
*Non dispenser model - Type 2
Operation
Refreshment Centre 
Button
Refreshment Centre 
(Applicable to some 
models only)
Function display board
Optional
Type-1
Type-2
NOTE
• Your model may not include every option.
ENGLISH
ENGLISH
 
						

							1414
Express freezer.
Child  lock  : \fold  3 sec. Filter 
reset \button .
Temperature  adjustment \button
for  freezer  compartment.Temperature  adjustment  \button
for  refrigerator  compartment .Display Saving Mode
Display  Saving Mode
Display  Saving Mode
LIGHT/
Filter reset  \futton .
Lig\bt  ON/OFF  \futton - Optio n
Dispenser  selection \futton
Display Saving Mode
LIGHT/
Filter reset  \futton .
Lig\bt  ON/OFF  \futton - Optio n
OperationOperation
*Dispenser model -\g Type 1
\bOTE• Your model may not include every option.• Display Type - 3 and Type - 4\f The control display is operated by touch. Excessive moisture on the display panel may cause a malfunction. Please keep display clean and dry.
Refreshment Center
Water/Ice output
Dispenser push swi\gtch
Function display boardOptional
Type-1
Type-2
Type-3
Type-4
ENGLISH
 
						

							15
Display Power Saving Mode
Display Power Saving Mode
Display Power Saving Mode
Operation
*Dispenser model -\g Type 2
\bOTE• Your model may not include every option.
Refreshment Center Button
Refreshment Center(Applicable to some models only)
Water/Ice output
Dispenser push swi\gtch
Dispenser Lamp (hi\gdden)
Operation
Function display boardOptional
Type-1
Type-2
Type-3
ENGLISH
ENGLISH
 
						

							1616
Start
Start
OperationOperation
This function save the display power
You can adjust temperature of the fridge and\s freezer compartments
Display panel will automatically turn off in 20 seconds and turn on again when you open the door or p\gress the button again.
Press the FREEZER and E\gXPRESS FRZ. buttons simultaneously\g and hold them for 5 seconds until the Ding sounds\g. All LED/LCDs will then turn O\b, then OFF. When the power saving mode is activated, the display will remain off until the next time the door is opened\g. Then, it will come on whenever a door is opene\gd or a button is pressed and remain on for 20 seconds after the last door o\gpening or button selec-tion. To deactivate the power saving mode, press the FREEZER and E\gXPRESS FRZ. buttons simultaneously\g and hold them for 5 seconds until the Ding sounds\g.
• The actual inner temperature varies depending on th\ge food status.  The indicated temperature is a target temperature, not the actual temperature within the refrigerator.• Until your refrigerator has settled from transit, it will not perform at its optimum.  It takes 2 or 3 days for the fridge to stabilise.  During this period, please adjust th\ge temperature as above.
Display power-
saving (on some 
model)
Display  
POWER-SAVE 
mode (on some 
model)
Re\brigerator 
control
Freezer  
control
ENGLISH
 
						

							17
Display Power Saving Mode
Operation
*Dispenser model -\g Type 3
Water/Ice output
Type 1
Type 2
Type 3
Dispenser push swi\gtch
Dispenser Lamp (hi\gdden)
Refreshment Center Button
Refreshment Center (Applicable to some models only)
\bOTE• Your model may not include every option.• The control display panel is operated by touch. Excessive moisture on the display panel may cause a malfunction. Please keep display panel clean and \gdry.
Operation
ENGLISH
ENGLISH
 
						

							1818
Operation
A\ftomatic ice maker
Operation
Display Power Saving Mode
You can adjust temperature of the fridge and\s freezer compartments
Freezer Compartment temperature adjustment
Refrigerator Compartment temperature adjustment
Press the FREEZER and E\gXPRESS FRZ. buttons simultaneously\g and hold them for 5 seconds until the Ding sounds\g. All LED/LCDs will then turn O\b, then OFF. When the power saving mode is activated, the display will remain off until the next time the door is opened\g. Then, it will come on whenever a door is opene\gd or a button is pressed and remain on for 20 seconds after the last door o\gpening or button selec-tion. To deactivate the power saving mode, press the FREEZER and E\gXPRESS FRZ. buttons simultaneously\g and hold them for 5 seconds until the Ding sounds\g.
*Whenever pressing button, setting is repeated in the order of (Middle )→(Middle Strong )→(Strong)→(Weak)→(Middle Weak).
▪ The actual inner temperature varies depending on th\ge food status.  The indicated temperature is a target temperature, not the actual temperature within the refrig-erator
▪ Until your refrigerator has settled from transit, it will not perform at its optimum.  It takes 2 or 3 days for the fridge to stabilise.  During this period, please adjust th\ge temperature as above.
How to adj\fst the 
temperat\fre in the 
\breezer compart-
mentSetting temperat\fre
Setting temperat\fre
How to adj\fst the 
temperat\fre in 
the re\brigerator 
compartment
ENGLISH