LG Gw B207 Flqa Owners Manual

							
1. Place your appliance where it is easy touse.
2. Avoid placing the unit near heat sources, direct sunlight or moisture.
3. To ensure proper air circulation around the fridge -freezer, please maintain sufficient
space on both the sides as well as top and
maintain at least 2 inches (5 cm) from the
rear wall.
4. To avoid vibrations, the appliance must be leveled.
5. Dont install the appliance below 5 °C. It may cause affect the performance. 

6
Installation
Select a good
location

Where to Install
Disposal of theold applianceThis appliance contains fluid (refrigerant, lubricant)and is made of p\
arts and materials
which are reusable and/or recyclable.
All the important materials should be sent to the collection center of w\
aste material
and can be reused after rework (recycling). For take back, please cont\
act with the
local agency.
 
						

							
7
Installation
Door removal
Failure to do so could result in death or serious injury.
If your access door is too narrow for the
refrigerator to pass through, remove the
refrigerator door and pass the refrigerator laterally. 
Electric Shock Hazard 
Disconnect electrical supply to refrigerator before installing. 
Remove the lower cover by lifting upward, and
remove clip, and then pull up the feed water tube
while pressing area 
shown in the figure to the
right.
Remove lower cover and
then feed water tube
Warning
Remove the freezer
compartment door
Remove the refrigerator door

1) Removing the hinge cover by loosening the
screws. Separate all connection wires except
for the earth line after.
2) Remove the keeper by rotating it counter clockwise (
) and then lifting the upper
hinge up (
 ).
3) Remove the freezer compartment door by
lifting it upward. This time, the door should
be lifted enough for the feed water pipe tube
to be completely pulled out.
1) Loosen the hinge cover screws and remove the cover. Remove connection wire, if any,
except for the earth line.
2) Remove keeper by rotating it clockwise (
)
and then remove the upper hinge by lifting
it up (
).
3) Remove the refrigerator compartment door by lifting it up.
•If a tube end is deformed or abraded, cut the part away.
NOTE
•When removing the upper hinge, be careful that the door does not fall fo\
rwards .
NOTE
•Move the refrigerator compartment door passing through the access door a\
nd lay
it down, but be careful not to damage the feed water pipe tube.
NOTE

Lower cover
Lower hinge Lower hinge Keeper
Feed water tube

Connection
wires
Hinge
cover
Upper hinge Keeper
Upper hinge
Earth line

Upper hinge
Connectionwires
 
						

							
8
Installation
Door replacement
Feed water pipe installation
(*Dispenser model only)
Pass the refrigerator laterally through the access
door as shown in the right figure.

Automatic ice maker operation needs water pressure of 147~834 kPa (1.5~8.5
kgf/cm2) (That is, an instant paper cup (180 cc) will be fully filled within 3 sec.).

If water pressure does not reach the rating 147 kPa (1.5 kgf/cm2) or below, it is
necessary to purchase a separate pressure pump for normal automatic icin\
g and
cool water feed.

Keep the total length of the feed water pipe tube within 8 m and be careful for the
tube not be bent. If the tube is 8 m or longer it may cause trouble in water feed
owing to the drain water pressure.

Install the feed water pipe tube at a place free from heat.

Connect to potable water supply only.

Refer to instructions with water filter kit for installation.
Mount them in the reverse sequence of removal after they pass through th\
e access
door.
Pass the
refrigerator 
Before
installation
Warning

1
2
3
4
5
M
a
x
FR Z
TE MP RE
F
TE MP
Mi
n
5
4
3
2
1
Max
 
						

							
9

Installation
Height adjustment
Level the door by inserting flat (-type) driver into the groove of the left height adjusting
screw and rotate it clockwise ( 
).
Level the door by  inserting flat (
-type) driver into the groove of the right height
adjusting screw and rotate it  clockwise (
).
The refrigerator doors will close smoothly by heightening the front side\
 by adjusting
the height adjusting screw. If the doors do not close correctly, perform\
ance may be
affected.
If the freezer
compartment door is lower than the refrigerator
compartment door
If the freezer
compartment door is higher than the refrigerator
compartment door
After leveling the door height





Next1. Wipe off all dust accumulated during shipping and clean your appliance t\
horoughly.
2. Install accessories such as the ice cube box, cover evaporating tray, et\
c., in their
proper places. They are packed together to prevent possible damage durin\
g shipping.
3. Connect the power supply cord (or plug) to the outlet. Dont double up\
 with other appliances on the same outlet.
 
						

							
10

Operation
Starting
When your refr ige ra tor  is frst in stalled, allo w it to stab ilize at normal ope rating
t e mpera tures f or 2-3 hour s prior  to flling it with  f r e sh  or frozen foods. 
If  op era tion  is in terrup ted, wait  5 min utes be fo re  rest artin g .

Optional
T ype-1
T ype-2 Function display board
Display 
Power Saving  Mode 

Refreshment Center
Refreshment Center 
Button

Adjusting the temperatures and functions
*Non dispenser model - Type 1
 
						

							
Operation
OptionalT ype-1
T ype-2
T ype-3 Function display board
Exp
re ss freez er. Child  lock  :  H old3  secs.
D is p lay  Savin g  M od e
D is p lay  Savin g  M od e
D is p lay  Savin g  M od e
Temp erature a d just ment  b utt o n
for  freeze r comp artme nt.Temp erature a d just ment  b utt o n
For  re fri gerat or comp artmen t.
12
•Your model may not include every option.•Display Type-3: The control display is operated by touch. Excessive mois\
ture on the
display may cause a malfunction. Please keep display clean and dry.
NOTE
* N on D ispens er m odel - Type 2 
 
						

							
11


\b	

\f \f	


\b	

\f
\b	


  
	 

	 
  

\b	

\f \f	
\f\f

Operation
•Your model may not include every option.
NOTE

*Dispenser model -  Type 22 1
 
						

							
13
Operation
OptionalT ype-1
T ype-2
T ype-3 Function display board
E
xpr ess fre ezer .
C hil d  l ock  : H old  3  sec . F
il t e r reset  but to n .
Tempe ra tu re  adj ustment  button
f or  fr eezer  compartm ent .Tempe ra tu re  adj ustment  butto n
f or  re friger ato r com partm ent .
Displ ay Savin g  M od e
D ispl ay Savin g  M od e
D ispl ay Savin g  M od e
LIGH T/
Filte r res et b utton.
L ight  ON/OF F but ton  - O ptio n
D isp enser  select ion  butto n
•Your model may not include every option.•Display Type-3: The control display is operated by touch. Excessive mois\
ture on the
display may cause a malfunction. Please keep display clean and dry.
NOTE
*D isp en se r m odel - Type 2
 
						

							
Optio nal Typ e-1 Typ e-2 Type- 3
FR Z
T EM P
  S etti ng
Tem peratur e
  S etti ng
Tem peratur e
Optio nal Typ e-1 Typ e-2 Type- 3
REF
T EM P

You can adjust temperatur e of and freezer room and refrigerator room.
Whenever pre ssing  b utt on,  settin g is  repeated in t he order.
The actual in ner tempe ra tu re varies  dep ending  on the food statu s, as the
indicat ed  set ting  t empe rature  is a tar get temper ature, no t actual temp erature
w ithin re fr iger ator .
Refrigeration funct ion is w eak in the initial time .  Please  adjust  temp erature as
above af ter using re frige rator for min imum 2~3 days.
-190C -210C -220C -230C -150C -160C -170C
30C 20C 10C 00C 60C 50C 40C
How to adjust the
temperature in  the freezer
compartment
How to adjust the temperature in 
the refrigerator compartment
Operation
14
This function save the display power 
Press t he FRE EZER and  EXPRE SS FRZ. butto ns simultan eously and  hold t hem for 5
seconds u ntil  th e Din g s o u nds. All L ED/LCDs will t hen turn O N, then O FF. When  the
powe r savin g m od e is act ivated, the  display will  remain  of until the n ext time the door
is o pen ed . T hen, it will co me on whene ver a door  is o pene d or a bu tton is  pressed and
r e main o n for  20 seco nds af ter the  last  door op ening or butt on s election . To deactivate
t h e pow er saving  mode, pr ess t he FRE EZ ER an d EXPRESS  FRZ. buttons
simultaneously and hold them for 5 seconds until the Ding sounds.
Display power saving 
(on some model)
Start
Start
 
						

							
Operation

•Your model may not include every option.•The control display is operated by touch. Excessive moisture on the disp\
lay may
cause a malfunction. Please keep display clean and dry.
NOTE
13
3